Dukane Imagepro 9100hc D-ila Multimedia Projector Users Manual

21
Connecting to Various Devices
Connection
•When connecting a video device, please use a TBC along with it, or use one with a built-in TBC.
•Use of an extension cable to connect a video device and the projector could cause image deterioration or projection
failure.
•When a signal with much jitter is reproduced on a VCR, or special-effect playbacks are performed, the upper part of the
image or the screen may be interrupted, erased or distorted.
Connecting to Devices
RPR/CRGYBPB/CBVDVIH/CS
PC1PC3PC2
AUDIO...

22
Connecting to Various Devices

Connecting to Computers
•When the [PC2] input terminal is used, “PC2(BNC)” must be selected from the
“Options” menu. ( ☞ page 39)
• When connecting an audio output terminal such as a computer sound source to
the projector, connect to the [AUDIO IN] terminal using the separately available
audio cable.
• When connecting to PC-9800 Series computers, a separately available conver-
sion adapter is necessary. Please confirm the monitor connector type before use....

23
Connecting to Various Devices
RPR/CRGYBPB/CBVH/CS
PC1PC2
AUDIO INREMOTESCREEN
TRIGGER RS-232C OUT RS-232C INCONTROL
BPB/CBVH/CS
PC1PC2
NREMOTERS-232C OUT RS-232C INCONTROL
BPB/CBVH/CS
PC1PC2
INREMOTERS-232C OUT RS-232C INCONTROL
It is possible to control the projector with a computer by connecting the computer to the [CONTROL RS232C IN] terminal of the
projector. • Please request a connection cable from us if needed.
•F or more information, please contact your authorized dealer.

Control from external...

24
Connecting to Various Devices
1.Connect the supplied power cord to the power in-
put terminal of the projector
2.Insert the main plug of the supplied power cord into
the wall outlet
After all devices have been connected, connect the supplied power cord.
Connecting the Power Cord (supplied)
Cautions Against Fire and Electric Shock
● Since the power requirement of the projector is high, please insert the power plug directly into a wall outlet.
●When not using devices, remove the power plug from the wall...

25
Basic Operations
Note
•Messages are displayed in the language set
by the user in the “Language” menu. The pre-
set language upon purchase is “English”. The
user can choose from 8 national languages.
(☞ page 39)
However, the input mode ([PC1], [PC2],
[PC3], [Y/C], [VIDEO]) and button indications
([FREEZE], [D.ZOOM], [EXIT]) are only dis-
played in English irrespective of the display
language setting.
1.Power On
1Insert the power cord into the wall outlet
•The [STAND BY] indicator lights up when the...

26
Basic Operations

Display using the direct buttons
The direct buttons enable direct switching and op-
eration without having to go through the menu.
Input mode can be selected
by pressing the [PC] button or
the [VIDEO] button.
When the [DIGITAL ZOOM], [VOLUME], [V-KEY-
STONE] or [H-KEYSTONE] buttons are pressed,
the level bar of the function is displayed.
PC1
When “Line display” (☞ page 39) is set
to “5sec” : After changing an input , the
new selection will appear on the screen
for about 5 seconds....

27
Basic Operations
5.Adjusting the Sound Volume

To increase the volume :press [VOLUME]ª (0 ➞ 50)

To lower the volume :press [VOLUME]· (50 ➞0)
When “Menu display” (☞ page 39)
is set to “15sec”, after pressing the
[VOLUME] button, the sound vol-
ume display will appear on the
screen for about 15 seconds.
(Press [EXIT] button to immedi-
ately remove the “Audio-Vol” dis-
play.)
Note
•When the sound volume is displayed on the screen, pressing
the [PRESET] button will reset the set value to “0”.
Note
•The...

28
Frequently used Convenient Functions
When an image is projected onto the screen, the following operations
can be performed directly without going through the menu operation.
(☞ page 27 for VOLUME operation.)
 DIGITAL ZOOM
 HIDE
 FREEZE
 KEYSTONE
 QUICK ALIGN. (quick alignment)
Basic Operations
Note
•The quality of the zoomed image is reduced
in comparison with the original.

“Digital zoom” Display
1Magnifying power display
“x1.0”: 1 time (standard) “x2.0”: 2 times
“x1.2”: 1.2 times “x2.5”: 2.5 times...

29
Basic Operations
  Turning Off Image and Sound
Video images and audio output can be turned off temporarily.
Press the [HIDE] button once
•Images and audio output turned off.
Press the [HIDE] button again.
Images and audio output turn on again
Note
•When the projected image input is changed, the HIDE function is
cancelled and image and sound return.
  Displaying a Still Picture
The projected image can be paused temporarily.
•This operation cannot be operated by the projector buttons. Please
use the...

30
“Vert.keystone” Display
1Adjusted value
range:  -100 ~ 0 ~ 100
2Level displayed
level displayed is based on the adjustment value.

 “Horiz.Keystone” Display
1Adjusted value
range:  -40 ~ 0 ~ 40
2Level displayed
level displayed is based on the adjustment value.
Basic Operations
  Removing the Trapezoidal Distortion of the Image
Depending on the angle of projection onto the screen, the image may get
distorted in a trapezoid form sometimes.
When installing the projector or screen for the first time, or...