Dukane Imagepro 9100hc D-ila Multimedia Projector Users Manual

Users Manual
D-ILA Multimedia Pr ojector
Model 9100HC
Audio  Visual Pr oducts 

2
SAFETY PRECAUTIONS
About burning-in of the D-ILA device
Do not allow the same still picture to be projected for a long
time or an abnormally bright video picture to be projected.
Do not project video images with high-intensity or high contrast
on a screen. The video image could be burnt into the D-ILA
device.
Use special care when projecting video games or computer pro-
gram images. There is no problem with ordinary video-cassette
playback images.
About the installation place
Do not install the...

3
–Slots and openings in the cabinet are provided for ventilation.
These ensure reliable operation of the product and protect it
from overheating. These openings must not be blocked or
covered. (The openings should never be blocked by placing
the product on bed, sofa, rug, or similar surface. It should not
be placed in a built-in installation such as a bookcase or rack
unless proper ventilation is provided and the manufacturer’s
instructions have been adhered to.)
For proper ventilation, separate the...

4
Safety Precaution
The wire which is colored green-and-yellow must be connected
to the terminal which is marked with the letter E or the safety
earth or colored green or green-and-yellow.
The wire which is colored blue must be connected to the termi-
nal which is marked with the letter N or colored black.
The wire which is colored brown must be connected to the ter-
minal which is marked with the letter L or colored red.
When replacing the fuse, be sure to use only a correctly rated
approved type,...

5
Caution
About burning-in of the D-ILA device
●Do not allow the same still picture to be projected for a
long time or an abnormally bright video image to be pro-
jected.
Do not project video images with high-intensity or high con-
trast on a screen. The video image could be burnt into the
D-ILA device.
Use special care when projecting video games or computer
program images.
There is no problem with ordinary video cassette playback
images.
Viewing conditions
●Brightness of the room
Please avoid having...

6
Contents
Accessories
The following accessories are packed together with this projector.
Please confirm all items. If any item is missing, please contact your dealer.
Instructions   .................. ........................................................................\
.................................. .............x 1
Guarantee ........................................................................\
.............................................. ..................... x 1
Pow er Cord...

7
Controls and Features
Front Side/ Top Surface/ Left Side
7Air Inlets (on the front, right, and bottom side of
projector)
The air inlets absorb air to cool the internal components of
the projector. Do not block or allow warm air to blow into
them as it may cause damage.
•The air inlet filter on the right side cannot be removed.
Please clean the filter regularly with, for example, a
vacuum cleaner.
8Remote Sensor (Front)
When operating with the remote control, aim it towards this
sensor. (☞ page 18)
•A...

8
Rear Side/ Right Side/ Bottom Surface
Controls and Features
qConnector Panel
For details, refer to ‘Connector Panel’. (☞ page 9)
wSpeaker
Built-in speaker located here.
eLamp Cover
Remove this cover when replacing the lamp. (☞ page 47)
rExhaust Vent
Warm air is expelled through these vents to keep the sys-
tem cool. Please do not block the exhaust vents.
tRemote Sensor (Rear)
When operating with the remote control, aim it towards this
sensor. (☞ page 18)
•A remote sensor is also provided at the front...

9
Controls and Features
Connector Panel
1[PC2] Input terminal (BNC x 5)
This is an input terminal for component signals (Y, CB, CR)
or DTV-format (Y, P
B, PR) signals. Devices which have com-
ponent signal output terminals can be connected. This ter-
minal can also be used as multipurpose video input termi-
nals that allow input of the following signals: analog RGB
signals, vertical sync (V) signals, and horizontal sync (H)
signals/ composite signals (Cs). Devices which have ana-
log RGB signals output...

10
Control Panel on the Projector
Controls and Features
Indicator Display on the Control Panel
Stand-by, operate and cool down modes, together with other operational activities are indicated by differing combinations of Indica-
tors appearing on the Control Panel.
•Please refer to Page 47 for explanations on warning indication for *
1, and Page 55 for *2.
[STAND BY] light on
Projector is in stand by mode
[OPERATE] light on
Projector is in operate mode
(In operation/ during projection)
[STAND BY]...