Dukane Imagepro 9100hc D-ila Multimedia Projector Users Manual

							21
Connecting to Various Devices
Connection
•When connecting a video device, please use a TBC along with it, or use one with a built-in TBC.
•Use of an extension cable to connect a video device and the projector could cause image deterioration or projection
failure.
•When a signal with much jitter is reproduced on a VCR, or special-effect playbacks are performed, the upper part of the
image or the screen may be interrupted, erased or distorted.
Connecting to Devices
RPR/CRGYBPB/CBVDVIH/CS
PC1PC3PC2
AUDIO INREMOTESCREEN
TRIGGERRS-232C OUT RS-232C IN Y/C VIDEOCONTROLVIDEO IN
•Thoroughly read the manual that comes with each video device.
•Use the supplied AV connection cable. S-video (Y/C) cable, BNC cable and PC Audio cables are not supplied.

Connecting to Video Devices
Before connection, be sure to turn off both the projector and the device.
Image input
•Connect to component signal output
device, DTV format signal output device,
etc.
•When the [PC2] input terminal is used, the
“PC2(BNC)” item in “Options” menu must
be correctly set. (☞ page 39)
Sound input
•Connect to [AUDIO IN] terminal. Image input
•Connect a composite image signal output
device or Y/C (S-video) image output device.
Sound input
•Connect to [AUDIO IN] terminal.
Right side of projector
VCR (Video cassette recorder)
Video Device 2 BNC Cable (sold separately)
AV connection cable
(supplied) PC Audio cable
(sold separately)S-video cable
(sold separately)
Video Device 1
CamcorderDVD player
D-VHS or DVD player etc.
HX-1E_p15-31_En.p6510/3/03, 6:08 PM 21 
						

							22
Connecting to Various Devices

Connecting to Computers
•When the [PC2] input terminal is used, “PC2(BNC)” must be selected from the
“Options” menu. ( ☞ page 39)
• When connecting an audio output terminal such as a computer sound source to
the projector, connect to the [AUDIO IN] terminal using the separately available
audio cable.
• When connecting to PC-9800 Series computers, a separately available conver-
sion adapter is necessary. Please confirm the monitor connector type before use.
RPR/CRGYBPB/CBVDVIH/CS
PC1PC3PC2
AUDIO INREMOTESCREEN
TRIGGER RS-232C OUT RS-232C IN Y/C VIDEOCONTROLVIDEO IN
•
Thoroughly read the manuals that come with the computer used.
• Prepare cables for connecting the devices.
❈ There are some notebook type computers that do  not
allow the computer’ s LCD to work if an external
display device is connected. With such computers, the
LCD display and external display output need to be
switched.
To [PC2]
To   [DVI]
To  [PC1]
P
ersonal Computer connector cable (sold separately)
Right side of projector
Conversion
adapter for MAC
(sold separately) To
 monitor
connector Separated cable (sold separately)
Desktop type (DOS/V, PC-9800 etc.)
Desktop type (DOS/V, etc.)
Desktop type
(Macintosh)
Notebook Type
Desktop type To
 monitor
connector
To  monitor
connector
HX-1E_p15-31_En.p65 10/3/03, 6:08 PM
22 
						

							23
Connecting to Various Devices
RPR/CRGYBPB/CBVH/CS
PC1PC2
AUDIO INREMOTESCREEN
TRIGGER RS-232C OUT RS-232C INCONTROL
BPB/CBVH/CS
PC1PC2
NREMOTERS-232C OUT RS-232C INCONTROL
BPB/CBVH/CS
PC1PC2
INREMOTERS-232C OUT RS-232C INCONTROL
It is possible to control the projector with a computer by connecting the computer to the [CONTROL RS232C IN] terminal of the
projector. • Please request a connection cable from us if needed.
•F or more information, please contact your authorized dealer.

Control from external device
Connect to Computer Connect to the [IN]
terminal of third projector
Connection for controlling more than one projector
By using the [CONTROL] terminal, more than one projector can be controlled simultaneously by one computer.
Connect these projectors in series by connecting the [OUT] terminal of the first projector to the [IN] terminal of the second
projector, then the [OUT] terminal of the second projector to the [IN] terminal of the third projector, etc.
RS-232C connection cable (sold separately)
(Cross cable) Second projector
Projector RS-232C connection cable
(sold separately)
(Cross cable)
Notebook type
HX-1E_p15-31_En.p65
10/3/03, 6:08 PM
23 
						

							24
Connecting to Various Devices
1.Connect the supplied power cord to the power in-
put terminal of the projector
2.Insert the main plug of the supplied power cord into
the wall outlet
After all devices have been connected, connect the supplied power cord.
Connecting the Power Cord (supplied)
Cautions Against Fire and Electric Shock
● Since the power requirement of the projector is high, please insert the power plug directly into a wall outlet.
●When not using devices, remove the power plug from the wall outlets.
●Do not use power cords other than those supplied.
● Do not use a power voltage different from that which is indicated.
● Do not cut, tear or modify the power cords. Also, do not put a heavy object on, heat, or stretch the power cords, otherwise they
may be damaged.
●Do not insert or pull out the plugs with a wet hand.

When using the projector, remove the Lens Cap
•Be sure to fit the lens cap on when the projector is not in use
to keep out dirt.
•Do not project with the lens cap attached.  The lens cap may
be deformed by heat or this may cause malfunction.
(e.g.)
2 1
Power cord (supplied)
Lens Cap
HX-1E_p15-31_En.p6510/3/03, 6:08 PM 24 
						

							25
Basic Operations
Note
•Messages are displayed in the language set
by the user in the “Language” menu. The pre-
set language upon purchase is “English”. The
user can choose from 8 national languages.
(☞ page 39)
However, the input mode ([PC1], [PC2],
[PC3], [Y/C], [VIDEO]) and button indications
([FREEZE], [D.ZOOM], [EXIT]) are only dis-
played in English irrespective of the display
language setting.
1.Power On
1Insert the power cord into the wall outlet
•The [STAND BY] indicator lights up when the main power is
inputted.
2Press the [OPERATE] button on the projector (or the [OP-
ERATE] button on the remote control unit) for one second
or more
•The [OPERATE] indicator lights up and the projected image
slowly appears.
2.Selecting the image to be projected

Press [VIDEO] to select which of the image devices of those
connected to the [VIDEO IN] ([VIDEO] or [Y/C]) terminals is
output
•Each time you press either button, the selected input changes
as follows.
Notes
•Upon projection, the image may flicker for a few seconds, but
this is not a malfunction.
•When the lamp is turned on, it will slowly become brighter. It
will take more than a minute for the brightness to stabilize.
[VIDEO] : Image from the input [VIDEO]
terminal on the right hand side
of projector will be projected.
[Y/C] : Image from the input [Y/C] ter-
minal on the right hand side of
the projector will be projected.
MENU
V-KEYSTONEPC LAMP
H-KEYSTONE VOL.
EXIT
ENTER
VIDEO
TEMPSTAND BYOPERATE
1-2
2
QUICK ALIGN. PC VIDEOVOLUME
PRESET HIDE
ENTER
MENU EXITFREEZE
OPERATE
V-KEYSTONEH-KEYSTONESCREENDIGITAL
ZOOM
FOCUS
W
S
1-2
2
LAMP TEMPSTAND BYOPERATE
LAMP TEMPSTAND BYOPERATE
OPERATEOPERATE
VIDEO
VIDEO
Basic Operation Procedures
Once the basic settings are done, follow the procedures below:
Light on
  Projector: Indicator
Light on
  Projector: Indicator Remote
control unit Projector:
Control panel
Remote
control unit Projector:
Control panel
Notes
•Sound is formed from sound signals connected to the [AU-
DIO IN] terminal.
•When no image is input to the selected input terminal, the
message “No Input” is displayed on the screen. (☞ page 53)
If projector set up is not yet complete, please read ‘Adjustments and Settings Using Menus’ on page 32 and perform the necessary
settings.
[VIDEO][Y/C]
HX-1E_p15-31_En.p6510/3/03, 6:08 PM 25 
						

							26
Basic Operations

Display using the direct buttons
The direct buttons enable direct switching and op-
eration without having to go through the menu.
Input mode can be selected
by pressing the [PC] button or
the [VIDEO] button.
When the [DIGITAL ZOOM], [VOLUME], [V-KEY-
STONE] or [H-KEYSTONE] buttons are pressed,
the level bar of the function is displayed.
PC1
When “Line display” (☞ page 39) is set
to “5sec” : After changing an input , the
new selection will appear on the screen
for about 5 seconds.

To select a computer or other devices connected to [PC1],
[PC2] or [PC3]: Press [PC]
•Upon pressing the button, the input mode changes as follows.
When “Line display” (☞ page 39) is set
to “5sec”: After changing an input, the
new selection will appear on the screen
for about 5 seconds.
Notes
•Sound is formed from sound signals connected to the [AUDIO IN]
terminal.
•When no image is input to the selected input terminal, the mes-
sage “No Input” is displayed on the screen. (☞ page 53)
•When the [PC2] input terminal is used, “PC2(BNC)” must be se-
lected from the “Options” item in the main menu. (☞ page 39)
3.Adjusting the Zoom Ring (the screen size)

To enlarge the screen size:Turn the zoom ring towards the
‘Wide side’

To reduce the screen size:Turn the zoom ring towards ‘Tele
side’
4.Adjusting the Focus Ring (Focus)

To focus on nearer points:Turn the focus ring towards the
‘Near side’

To focus on farther points:Turn the focus ring towards the
‘Far side’
PC 1
PC 2
PC 3
Y/C
VIDEO
Audio-Vol 12
Digital zoom x1.2
Vert.keystone
0
Horiz.Keystone
0
3.
4.
VIDEO
PC
PC
PC1 PC2 PC3
[PC1]: Projects image from [PC1] input terminal on
the right hand side of the projector.
[PC2]: Projects image from [PC2] input terminal on
the right hand side of the projector
[PC3]: Projects image from [PC3] input terminal on
the right hand side of the projector. Screen display
Screen display
‘Tele side’
‘Wide side’
‘Near side’
‘Far side’Remote
control unit Projector:
Control panel
HX-1E_p15-31_En.p6510/3/03, 6:08 PM 26 
						

							27
Basic Operations
5.Adjusting the Sound Volume

To increase the volume :press [VOLUME]ª (0 ➞ 50)

To lower the volume :press [VOLUME]· (50 ➞0)
When “Menu display” (☞ page 39)
is set to “15sec”, after pressing the
[VOLUME] button, the sound vol-
ume display will appear on the
screen for about 15 seconds.
(Press [EXIT] button to immedi-
ately remove the “Audio-Vol” dis-
play.)
Note
•When the sound volume is displayed on the screen, pressing
the [PRESET] button will reset the set value to “0”.
Note
•The [OPERATE] button will not work for approximately 1 minute
from when the light-source lamp is turned on. Wait approxi-
mately 1 minute before pressing.
Caution
•Please do not pull out the plug from the power source when
the [STAND BY] indicator is blinking. It will shorten the life of
the lamp and cause a malfunction.
MENU
V-KEYSTONEPC LAMP
H-KEYSTONE VOL.
EXIT
ENTER
VIDEO
TEMPSTAND BYOPERATE
5
QUICK ALIGN. PC VIDEOVOLUME
PRESET HIDE
ENTER
MENU EXITFREEZE
OPERATE
V-KEYSTONEH-KEYSTONESCREENDIGITAL
ZOOM
FOCUS
W
S
5
6-1
6-1
VOL.VOLUME
  
Audio-Vol      12
Audio-Vol 12
6.Power Off
1Press the [OPERATE] button on the projector (or the [OP-
ERATE] button on the remote control unit ) for  1 second or
more
•The [OPERATE] indicator will disappear, the [STAND BY] in-
dicator starts to blink, and the projector goes into the cool-
down mode. The [STAND BY] indicator will continue blinking
for approximately 90 seconds as the temperature of the light
source lamp cools (Cool Down Mode). Projector:
Control panelRemote
control unit
Screen display
Tu r n off
Projector: IndicatorBlink
Projector:
Control panelRemote
control unit
2Plug out the power cord from wall outlet
LAMP TEMP
OPERATEOPERATESTAND BY
OPERATE
HX-1E_p15-31_En.p6510/3/03, 6:08 PM 27 
						

							28
Frequently used Convenient Functions
When an image is projected onto the screen, the following operations
can be performed directly without going through the menu operation.
(☞ page 27 for VOLUME operation.)
 DIGITAL ZOOM
 HIDE
 FREEZE
 KEYSTONE
 QUICK ALIGN. (quick alignment)
Basic Operations
Note
•The quality of the zoomed image is reduced
in comparison with the original.

“Digital zoom” Display
1Magnifying power display
“x1.0”: 1 time (standard) “x2.0”: 2 times
“x1.2”: 1.2 times “x2.5”: 2.5 times
“x1.4”: 1.4 times “x3.2”: 3.2 times
“x1.6”: 1.6 times “x4.0”: 4 times
2Level Display
Level shown is based on selected magnification.
 Enlarging the Image
We can zoom in while not changing the size of the projected image.  After
zooming, the position of the image displayed can be moved.
•This cannot be done using the projector buttons. Please use the re-
mote control unit.
1.Press [DIGITAL ZOOM] ª
•The “Digital zoom” display appears on the screen and the projec-
tor changes to the Digital Zoom Mode.
•The image on the screen can be enlarged in 8 stages by pressing
this button (including the standard size).
To reduce the size of the image
2.While “Digital zoom” display appears on the screen, you
can move the zoomed image with the cursor buttons on
the remote control

To see the upper part of zoomed image:
Press 

To see the lower part of zoomed image:
Press 

To see the right part of zoomed image:
Press 

To see the left part of zoomed image:
Press 
QUICK ALIGN. PC VIDEOVOLUME
PRESET HIDE
ENTER
MENU EXITFREEZE
OPERATE
V-KEYSTONEH-KEYSTONESCREENDIGITAL
ZOOM
FOCUS
W
S
Digital zoom   X1.2
Direction buttons availableDIGITAL
ZOOM“x2.0”
Digital zoom   X1.2Direction buttons availableDigital zoom    X2.0Direction buttons available
Digital zoom   X2.0Direction buttons availableDigital zoom   X2.0Direction buttons available
ENTER
DIGITAL
ZOOM
PRESET
When the [DIGITAL ZOOM] · button is pressed, the pre-
viously enlarged image will be reduced progressively until
it returns to the original size.
To reduce the image to the original size
When the [PRESET] button is pressed, the image will re-
turn to its original size and position.
(Please operate while “Digital zoom” is displayed.)
Remote
control unit
Remote control unit
HX-1E_p15-31_En.p6510/3/03, 6:09 PM 28 
						

							29
Basic Operations
  Turning Off Image and Sound
Video images and audio output can be turned off temporarily.
Press the [HIDE] button once
•Images and audio output turned off.
Press the [HIDE] button again.
Images and audio output turn on again
Note
•When the projected image input is changed, the HIDE function is
cancelled and image and sound return.
  Displaying a Still Picture
The projected image can be paused temporarily.
•This operation cannot be operated by the projector buttons. Please
use the remote control unit.
Press the [FREEZE] button
•The image pauses after the [FREEZE] button is pressed for a few sec-
onds and a message “Frozen” is shown in the center of the screen. An
icon indicating [FREEZE] mode will be displayed on the top right cor-
ner of the screen.
To de-freeze the image
When you press the [FREEZE] button again, the image de-freezes and
resumes.
Notes
•After de-freezing a still image, note that the projector will not play
the image that comes immediately after. (Should you want to play
the image that comes immediately after that at which the [FREEZE]
button was pressed, please pause the image using the controls at
the input device.)
•[MENU], [QUICK ALIGN.], [H-KEYSTONE] and [V-KEYSTONE]
buttons do not function when the image is still.
•The “Frozen” message will disappear after 5 seconds. To forcibly
clear “Frozen”, please press the [EXIT] button.
PRESET
MENUEXIT
ENTER
HIDE
QUICK ALIGN. PC VIDEOVOLUME
PRESET HIDE
ENTER
MENU EXITFREEZE
OPERATE
V-KEYSTONEH-KEYSTONESCREENDIGITAL
ZOOM
FOCUS
W
S
Frozen
FREEZE
FREEZE
HIDE
HIDE
Projector:
Control panelRemote
control unit
Remote control unit
[FREEZE] icon
Digital zoom available
HX-1E_p15-31_En.p6510/3/03, 6:09 PM 29 
						

							30
“Vert.keystone” Display
1Adjusted value
range:  -100 ~ 0 ~ 100
2Level displayed
level displayed is based on the adjustment value.

 “Horiz.Keystone” Display
1Adjusted value
range:  -40 ~ 0 ~ 40
2Level displayed
level displayed is based on the adjustment value.
Basic Operations
  Removing the Trapezoidal Distortion of the Image
Depending on the angle of projection onto the screen, the image may get
distorted in a trapezoid form sometimes.
When installing the projector or screen for the first time, or when reinstall-
ing in other rooms, etc., Keystone adjustments need to be made to re-
move trapezoid distortions.
1.Press [V-KEYSTONE] /  to adjust the trapezoid form in
the vertical direction
•A “Vert.keystone” display appears on the screen, and the projec-
tor goes into the KEYSTONE MODE.
Press button (
/ ) in the direction that corrects the trapezoid
form.
Notes
•The range where the trapezoidal distortion can be rectified is 30˚
vertically and 10˚ horizontally with respect to the projector screen.
However, when both are rendered together, the range of effective
rectification will be narrower.
•The picture quality may deteriorate when performing KEYSTONE
compensation. It is recommended to place the projector perpen-
dicularly to the screen.
•Depending on the signal inputted, the keystone adjustment range
may narrow or parts of the image may disappear. This is not a
malfunction.
•Interference patterns may appear on the screen when adjusting
the keystone. This is not a malfunction.
•To restore the original set value, press the [PRESET] button when
adjusting the [V-KEYSTONE] and  [H-KEYSTONE]. (Adjusted value:
0)
•During startup of projector, the KEYSTONE adjustment is not re-
flected in the D-ILA logo, user-set logo (when user-set logo is se-
lected) display and the no signal blue back display.
2.Press [H-KEYSTONE] /  to adjust the trapezoid form in
the horizontal direction
•A “Horiz.Keystone” display appears on the screen, and the pro-
jector goes into the KEYSTONE MODE.
Press button (
/ ) in the direction that corrects the trapezoid
form.
MENU
V-KEYSTONEPC
H-KEYSTONE VOL.
EXIT
VIDEO
QUICK ALIGN. PC VIDEOVOLUME
PRESET HIDE
ENTER
MENU EXITFREEZE
OPERATE
V-KEYSTONEH-KEYSTONESCREENDIGITAL
ZOOM
FOCUS
W
S
V-KEYSTONEV-KEYSTONEV-KEYSTONEV-KEYSTONE
H-KEYSTONEH-KEYSTONEH-KEYSTONEH-KEYSTONE
Vert.keystone 1
2
–12
Horiz.Keystone1
2
12
Projector:
Control panelRemote
control unitProjector:
Control panelRemote
control unit
Projector:
Control panelRemote
control unitProjector:
Control panelRemote
control unit
HX-1E_p15-31_En.p6510/3/03, 6:09 PM 30