Digital Projection Titan Wuxga 3d , Dual 3d, Titan Wuxga 330, 660 User Manual

Rev A   April 2011 Page 3.1
3. Getting Started
Contents
Switching the projector on ........................................................................\
.......................................3.2
Selecting an input or test pattern ........................................................................\
...........................3.2
Input ........................................................................\
........................................................................3.2
Test pattern...

Page 3.2 Rev A   April 2011
3. Getting Started Digital Projection TITAN WUXGA 3D, Dual 3D, 330. 660 User Manual
Selecting an input or test pattern
Input
Press  or   to change to the next input up or down the following list:
1. RGB1
2. RGB2
3. DVI (Single)
4. SDI
5. Composite Video
6. S-Video
7. Component
8. DVI (Single/Dual/Twin pixel-mapped)
Or press the numbered keys 1–8 to change directly to the input:
Test pattern
If you have no video source connected to the projector, then you can display a test...

Rev A   April 2011 Page 3.3
Digital Projection TITAN WUXGA 3D, Dual 3D, 330. 660 User Manual 3. Getting Started
Notes
 Each time a new lens is 
fitted to the projector, 
the calibration procedure 
must be carried out. See 
Setup menu, in Section 4. 
Controlling the projector.
  For more detailed information 
about:
  - using the control keys on the 
remote control or keypad,
 - using the menus,
 see the next section: 
Controlling the projector .
 When any of the three Lens 
adjustment keys is pressed,...

Page 3.4 Rev A   April 2011
3. Getting Started Digital Projection TITAN WUXGA 3D, Dual 3D, 330. 660 User Manual
Adjusting the projected image
Picture settings
Press a  key, followed by  and   to adjust these picture settings:
 Brightness    BRI 
Contrast    CON 
Saturation    SAT 
Phase    PHASE 
Aspect ratio    ASPECT
Geometry settings
Press Keystone  KEYST
followed by  and  to adjust the keystone correction.
Press Position   POS  (for all inputs except DVI)
followed by , ,  and  to adjust the picture...

Rev A  April 2011 Page 4.1
4. Controlling the projector
Contents
Overview ........................................................................\
.......................................................................4.5
Controlling the projector........................................................................\
.............................................4.5
Input modes and settings ........................................................................\...

Page 4.2 Rev A  April 2011
4. Controlling the projector Digital Projection TITAN WUXGA 3D, Dual 3D, 330. 660 User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Picture settings ........................................................................\
.......................................................4.15
Geometry settings ........................................................................\...

Rev A  April 2011 Page 4.3
Digital Projection TITAN WUXGA 3D, Dual 3D, 330. 660 User Manual 4. Controlling the projector
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section 4, Overview .
Colour menu ........................................................................\
..............................................................4.31
Colour Mode........................................................................\...

Page 4.4 Rev A  April 2011
4. Controlling the projector Digital Projection TITAN WUXGA 3D, Dual 3D, 330. 660 User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
On Screen Display ........................................................................\
..................................................4.47
OSD Position ........................................................................\...

Rev A  April 2011 Page 4.5
Digital Projection TITAN WUXGA 3D, Dual 3D, 330. 660 User Manual 4. Controlling the projector
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section 4, Overview .
Overview
Controlling the projector
The projector can be controlled from:
the remote control
the keypad
the RS232 input
the Ethernet input
For more information about controlling the projector using the RS232 and 
Ethernet inputs, see Remote communications protocol in...

Page 4.6 Rev A  April 2011
4. Controlling the projector Digital Projection TITAN WUXGA 3D, Dual 3D, 330. 660 User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Input modes and settings
Input mode detection
The projector can automatically detect the following parameters from the incoming 
video signal:
line frequency
frame rate
interlace / progressive
From these parameters the projector can determine input mode, for example:...