Digital Projection Titan Reference 1080p 3d, Dual 3d, Titan 1080p 3d, Dual 3d Ultra Contrast, Titan Dual Fastframe User Manual

							Rev C  April 2011 Page 2.17
Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual 2. Installation
Adjusting the rigging frame
Coarse adjustment of projector level should be made by adjusting the length of 
the supporting wires or chains, or by adjusting the position of the truss or rigging. 
Once the initial coarse adjustment has been made, fine adjustment can be made by 
turning the frame adjusters on the rigging frame:
To tilt the projector forwards and backwards (pitch adjustment), 
turn either the front pair or the rear pair of vertical adjusters, 
taking care to turn both adjusters by the same amount.
To tilt the projector from side to side (roll adjustment), turn either 
the left pair or the right pair of vertical adjusters, taking care to 
turn both adjusters by the same amount.
To rotate the projector around its vertical axis (yaw adjustment), 
turn the single horizontal adjuster at the rear.
•
•
•
Vertical 
adjusters
Horizontal 
adjuster
Notes
  Before suspending the 
projector, make sure that all the 
frame adjusters are set midway.
 Always make adjustments in 
pairs - never make a single 
adjustment - otherwise 
the projector frame could 
become distorted.
 Do not tilt the projector more 
than  ±10° in either direction 
when in use, as this may 
cause serious lamp failure, 
damage the lamp module 
and cause extra cost on 
replacement.
  It may be possible to use 
the projector in other 
orientations, depending on 
lamp configuration. For more 
information, contact Digital 
Projection.
±10°
±10° 
						

							Page 2.18 Rev C  April 2011
2. Installation Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual
Notes
 When stacking projectors, 
the stack MUST be vertical, 
to ensure that the stresses 
are distributed to all frame 
couplings.
 Make sure that the surface, 
ceiling or rigging that is 
to support the projector is 
capable of supporting the 
combined weight of all the 
projectors and lenses (see 
specification for weights) .
 Do not place heavy objects 
on top of the projector 
chassis. Only the chassis 
corners and the rigging frame 
are capable of withstanding 
the weight of another 
projector.
 Do not try to stack more than 
3 projectors.
 Separate backup safety 
chains or wires should 
always be used for each 
projector.
Stacking projectors
The rigging frame is capable of supporting the weight of up to two other projectors, 
using the built-in frame couplings. The projectors can be stacked on top of each 
other, or suspended below each other.
Carefully lower each projector down onto the top of the others, making sure that 
all four frame couplings engage fully.
Fit a locking pin into each coupling. A ball in the end of the pin prevents the pin 
from falling out – to insert or remove a locking pin, press the button on the end of 
the pin to release the ball.
Align the images from the projectors, following the instructions on the previous 
page and those in 
section  3. Getting started, Adjusting the lens  and 
Adjusting the projected image .
•
•
•
Locking 
pin
Frame 
couplings 
						

							Rev C  April 2011 Page 2.19
Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual 2. Installation
Notes
 For more information on 
selecting an input source, see 
section 4. Overview, Using 
the control keys, and Using 
the menus.
 For more information about pin 
connections and control codes 
see section 7. Appendix.
 For more information on 
input modes see  section 
4.
 Overview.
  Input 8 and 3D may not be 
present on some models
Connecting the projector
Signal Inputs
The following inputs are available:
Rear Input   
connection panel Control 
connection panel
5. Composite Video6. S-Video
7. Component
1. RGB1
2. RGB2
3. DVI
4. SDI
8. DVI
MAIN
SUB
3D Sync
Front Input  
connection panel 
						

							Page 2.20 Rev C  April 2011
2. Installation Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual
Notes
 There is no scaler on input 8.
  Images up to and including the 
native resolution of the display 
will be displayed pixel for pixel 
and centred.
 This enables the projector to 
maximise the image bandwidth 
and greyscale resolution.
Input format, DVI input 3
Single DVI-D
Sources upto 1920x1080 resolution; 8 bits per colour; 24- 60Hz.
Input formats, DVI input 8
Single DVI-D
Sources upto 1920x1080 resolution; 8 bits per colour; 24- 60Hz.
(Use MAIN input only)
Dual DVI-D
An input with increased frame rate.
Sources upto 1920x1080 resolution; 8 bits per colour; 24-120Hz.
(Use MAIN input only)
Twin Link (Twin Single DVI-D)
One input with increased bit depth, using both input connections:
Sources up to 1920x1080 resolution; 10 or 12 bits per colour; 24-60Hz.
(Use MAIN and SUB inputs)
Dual Pipe 3D
Two single input connections:
Sources up to 1920x1080 resolution; 10 or 12 bits per colour, at frame rates 
consistent with up to 148.5 MegaPixels/sec/pipe (including blanking).
(Use MAIN for left eye video stream and SUB input for right eye video stream) 
						

							Rev C  April 2011 Page 2.21
Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual 2. Installation
DVI Input connection examples
Single DVI video source
Single or Dual DVI video source Input 3
Input 8 MAINProjector
Input 8 MAIN
Input 8 SUB
 Twin DVI video source Projector
Notes
 
Dual DVI:
  high bandwidth/frame rate
 Twin DVI:
  increased bit depth/extended 
greyscale
 For important information about 
how Input 8 is used, see INPUT 
8 in the Notes column, and also 
Section 4, Overview.
Input and processing architecture
EDID handshaking on the DVI and rGB2 inputs
If you are using a computer DVI card or other source that obeys the EDID 
handshaking protocol, then the card or source will automatically configure itself to 
suit the projector.
If not, then you should refer to the documentation supplied with the source to 
manually set the resolution to 1920 x 1080 or the nearest suitable setting. Switch off 
the source, connect to the projector, then switch the source back on again. 
						

							Page 2.22 Rev C  April 2011
2. Installation Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual
Projector
3D server
Z screen or  3D glasses
Inputs 1-7
Sync
Video
Sync out
3D connection examples
3D sources up to 60Hz, requiring frame doubling and left/right 
interleaving Notes
 
For important information about 
how Input 8 is used, see INPUT 
8 in the Notes column, and also 
Section 4, Overview.
Sync in
Projector
3D server
Z screen or  3D glasses
Input 8
Sync
Video
Sync out
Sync in
3D sources up to 120Hz, not requiring frame doubling 
						

							Rev C  April 2011 Page 2.23
Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual 2. Installation
Notes
 For more information about pin 
connections and control codes 
see section 7. Appendix.
 For more information about 
using a browser to control the 
projector see  section 4. Using 
the menus.
Computer Null-modem  
cable
Control connection examples
LAN connection
All of the projector’s features can be controlled via a LAN connection, using a 
standard internet browser package such as Internet Explorer.
rS232 connection
Computer Crossed  
LAN cable
Computer
Hub or  LAN Un-crossed 
 
LAN cables
Projector
Serial 
RS232
LAN
Wired 
remote
Projector
Projector Projector 
						

							Page 2.24 Rev C  April 2011
2. Installation Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual
Notes
  Use only the power cable 
provided.
 Ensure that the power 
outlet includes a Ground 
connection, as this 
equipment MUST be earthed.
 Handle the power cable 
carefully and avoid sharp 
bends. Do not use a damaged 
power cable.
Power connection
When mains power is first applied, the projector will perform a self-test, then go into 
Standby mode.
The Power indicator on the control panel will show amber until the   POWER 
 
on the remote control or the keypad, is pressed for 3 seconds.
Power connection 
						

							Rev C  April 2011 Page 3.1
3. Getting Started
Contents
Switching the projector on ........................................................................\
.......................................3.2
Selecting an input or test pattern ........................................................................\
...........................3.2
Input ........................................................................\
........................................................................3.2
Test pattern ........................................................................\
..............................................................3.2
Adjusting the lens........................................................................\
.......................................................3.3
Focus ........................................................................\
......................................................................3.3
Zoom ........................................................................\
.......................................................................3.3
Shift ........................................................................\
.........................................................................3.3
Adjusting the projected image ........................................................................\
................................3.4
Picture settings ........................................................................\
.........................................................3.4
Geometry settings ........................................................................\
.....................................................3.4
Switching the projector off ........................................................................\
.......................................3.4 
						

							Page 3.2 Rev C  April 2011
3. Getting Started Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual
Selecting an input or test pattern
Input
Press  or   to change to the next input up or down the following list:
1. RGB1
2. RGB2
3. DVI (Single)
4. SDI
5. Composite Video
6. S-Video
7. Component
8. DVI (Single/Dual/Twin pixel-mapped)
Or press the numbered keys 1–8 to change directly to the input:
Test pattern
 If you have no video source connected to the projector, then you can display a test 
pattern as follows:
Press 
 on the remote control, to select a test pattern.
•
•
•
Switching the projector on
Connect the power cable between the mains supply and the projector .
Wait until the self-test has completed and the power indicator on the control 
panel shows amber. The lamp will be off, the shutter closed, and the projector 
will be in STANDBY mode.
Press POWER 
 on the remote control or the keypad, and hold for about 3 
seconds to switch the projector ON. The power indicator on the control panel will 
show green, the lamp will light and the shutter will open.
•
•
Notes
 
For more information about 
connecting the power cable, 
see Power Connections, in 
section 2. Installation .
 For more detailed information 
about:
  - using the control keys on the 
remote control or keypad,
 - using the menus,
 see the next section: 
Controlling the projector .
 3D images will be displayed in 
3D, only if  3D Mode is set to on: 
see section 4.Controlling the 
projector, Setup Menu, 3D .
 3D WUXGA images are 
possible only on Input 8.
 For important information about 
how Input 8 is used, see INPUT 
8 in the Notes column, and also 
Section 4, Overview.
  Only the Corrected White test 
pattern on Input 8 will fill the 
full height of the DMD, using all 
1200 pixels. All other patterns 
will be 1080 pixels high.
Power 
connection