Digital Projection Titan Reference 1080p 3d, Dual 3d, Titan 1080p 3d, Dual 3d Ultra Contrast, Titan Dual Fastframe User Manual

							Rev C  April 2011 Page 4.49
Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual 4. Controlling the projector
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section 4, Overview .
Notes
 
Setup Menu 
 Comunication
 When fresh batteries are 
inserted in the remote control, 
it will default to address  00. 
Remote control  00 is a master 
control,  able to control all 
projectors.
  If two or more projectors are set 
to the same address, they can 
be controlled from one remote 
control, provided they are 
connected by cable or in range 
of the infra red.
Communication Setup
Press  and   to select Comunication.
 Press  to open the Comunication submenu.
Serial port Baud rate
Press  and   to select Serial Port Baud Rate
 Press  and   to select from:
19200
9600
projector Address
The projector and the remote control need to be set to matching addresse\
s. Read 
the note to the right on this page, and follow the instructions in the o\
rder shown 
below:
1
  Set the projector address:
Press  to open the Projector Address control box.
Press  and   to select the address setting.
 Press   and    to adjust the address from:
00 to 99
 Use  and   to select from
Apply
 Press   to apply the new Projector Address.
or  Cancel
Press   or   to exit without making the change.
2 Set the remote control address as shown in Using the control keys, earlier in 
this section.
•
•
Setup menu continued 
						

							Page 4.50 Rev C  April 2011
4. Controlling the projector Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 
Setup Menu 
 Network
 Some items may be greyed out 
or not editable, due to the effect 
of other settings made in the 
Network submenu.
  For example, if a Wired 
Connection is selected:
  Wifi, Channel and SSID will be 
unavailable.
Setup menu continued
Network Setup
Press  and   to select Network.
 Press  to open the Network submenu.
LAN MAC Address
Projector’s unique ID  - for information only - cannot be changed.
Connection
Press  and   to select Connection
 Press  to open the Connection control box.
 Press  and   to select from:
Wired
Wireless
 Press   to apply the new Connection setting.
or  Cancel
Press   or   to exit without making the change.
•
•
• 
						

							Rev C  April 2011 Page 4.51
Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual 4. Controlling the projector
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section 4, Overview .
Notes
 IP Address cannot be changed 
if DHCP is set to ON.
 DHCP will set the the address, 
which will be displayed for 
information only.
Setup menu, Network continued
DHCp
Press  and   to select DHCP
 Press  to open the DHCP control box.
 Press  and   to select from:
On
Off
 Press   to apply the new DHCP setting.
or  Cancel
Press   or   to exit without making the change.
Ip Address
Press  and   to select IP Address
 Press  to open the IP Address control box.
 Use  and   to select each number in turn.
 Use  and   to adjust the number
 then move to the next number.
 Use  and   to select from
Apply
 Press   to apply the new IP Address.
or  Cancel
Press   or   to exit without making the change.
•
• 
						

							Page 4.52 Rev C  April 2011
4. Controlling the projector Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 IP Subnet cannot be changed if 
DHCP is set to ON.
  DHCP will set the the subnet 
mask, which will be displayed 
for information only.
Subnet Mask
Press  and   to select Subnet
 Press  to open the Subnet control box.
 Press  and   to select from:
Automatic
or one of the following:
Class C Masks
255.255.255.254  
255.255.255.252  
255.255.255.248  
255.255.255.240  
255.255.255.224  
255.255.255.192  
255.255.255.128  
255.255.255.0   (selected when setting is Automatic and IP class is C )
Class B Masks
255.255.254.0  
255.255.252.0  
255.255.248.0  
255.255.240.0  
255.255.224.0  
255.255.192.0  
255.255.128.0  
255.255.0.0  (selected when setting is Automatic and IP class is B)
Class A Masks
255.254.0.0  
255.252.0.0  
255.248.0.0  
255.240.0.0  
255.224.0.0  
255.192.0.0  
255.128.0.0  
255.0.0.0 (selected when setting is Automatic and IP class is A)
  Use  and   to select from
Apply
 Press   to apply the new Subnet Mask.
or  Cancel
Press   or   to exit without making the change.
•
Setup menu, Network continued 
						

							Rev C  April 2011 Page 4.53
Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual 4. Controlling the projector
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section 4, Overview .
Gateway Mask
Press  and   to select Gateway
Press 
 to open the IP Address control box.
Use 
 and   to select each number in turn.
Use  and   to adjust the number
then move to the next number.
Use 
 and   to select from
Apply
  Press   to apply the new IP Address.
or  Cancel
Press   or   to exit without making the change.
Wifi Channel
Press  and   to select Wifi Channel.
 Press  to open the Wifi Channel control box.
 Press  and   to select the channel number.
 Use  and   to adjust the channel number from:
0 to 14
 Use  and   to select from
 Apply
 Press   to apply the new Wifi Channel number.
or  Cancel
Press   or   to exit without making the change.
SSID
Projector’s ID  - for information only.
•
•
•
Setup menu, Network continued
Notes
 IP Gateway cannot be changed 
if DHCP is set to ON.
 DHCP will set the the gateway 
mask, which will be displayed 
for information only.
 The Wifi Channel  setting is not 
available if  Connection  is set to 
Wired. 
						

							Page 4.54 Rev C  April 2011
4. Controlling the projector Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 3D may not be present on some 
models
 
Setup Menu  
 3D
 If FastFrame  is turned on, then 
setting 3D Mode to Consumer 
or Professional will turn it off.
  When 3D Enable is on, it is not 
possible to turn on  FastFrame.
 It is important that 3D Input 
Assign is set correctly, so that 
the sync signal for the glasses 
or Z-screen is assigned to the 
correct input signal.
  WUXGA models only: 
3D images are possible only on 
Input 8.
3D Setup
Press  and   to select 3D.
  Press  to open the 3D submenu.
3D Mode
 Press  and   to select 3D Mode.
 Press  and   to select from:
Off
Professional
      all options will be available for adjustment
Consumer      3D Input Assign, 3D Format and Output Shuttering will 
be unavailable
In Consumer mode, the projector will automatically detect the following common 
3D standards:
Input 8
    Frame Packing:  1080p 24, 720p 50, 720p 60
Input 3     Frame Packing:  1080p 24
      Side by Side: 1080i 60
3D Input Assign
 Press  and   to select 3D Input Assign.
 Press  and   to select from:
1. RGB1
2. RGB2
3. DVI (Single)
4. SDI
5. Composite Video
6. S-Video
7. Component
8. DVI 3D
•
•
•
Setup menu, continued 
						

							Rev C  April 2011 Page 4.55
Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual 4. Controlling the projector
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section 4, Overview .
3D Format
Press  and   to select 3D Format.
 Press  and   to select from:
Sequential
Dual Pipe
Frame Packing
Top-And-Bottom
Side-By-Side (Half)
•
Notes
 
3D may not be present on some 
models
 None of the 3D options are 
avialable unless  3D Mode is set 
to Consumer or Professional.
Setup menu, 3D Setup continued
Sequential
Frame PackingTop and BottomSide by Side (Half)
Dual Pipe
Main Input
Sub Input 
						

							Page 4.56 Rev C  April 2011
4. Controlling the projector Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Dark time
Ghosting can be caused by the left and right images overlapping during t\
he time 
that the Z screen or 3D glasses are switching.
Press 
 and   to select Dark Time.
 Press  and   to adjust the slider (0 to 6000 µS).
Frame Dominance
The outgoing 3D frames are in pairs - the dominant frame being presented\
 first.
Press 
 and   to select Frame Dominance
 Press  and   to select from:
Left
Right
•
•
Notes
 
3D may not be present on some 
models
 None of the 3D options are 
avialable unless  3D Mode is set 
to Consumer or Professional.
  In order to achieve maximum 
light output and a smooth 
greyscale, whilst eliminating 
ghosting, the following 
procedure is recommended:
Set the Dark Time to a value 
appropriate to the glasses or 
Z-screen, say 1000 µS.
Adjust the Sync Delay time 
(see next page) to eliminate 
ghosting and achieve a smooth 
greyscale.
Repeat steps 1 and 2 until the 
best result is obtained.
 Set the frame dominance to 
match the incoming 3D video 
frame sequence.
1.
2.
3.
Setup menu, 3D Setup continued
Fully on
Fully off
Left
Right
Dark  time Dark 
time Dark 
time
Dominance Left
Dominance Right
LEFT 1RIGHT 1 LEFT 2RIGHT 2 LEFT 3RIGHT 3
LEFT 3RIGHT 1 LEFT 1RIGHT 2 LEFT 2RIGHT 3 
						

							Rev C  April 2011 Page 4.57
Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual 4. Controlling the projector
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also  Section 4, Overview .
Notes
 3D may not be present on some 
models
 None of the 3D options are 
avialable unless  3D Mode is set 
to Consumer or Professional.
  In order to achieve maximum 
light output and a smooth 
greyscale, whilst eliminating 
ghosting, the following 
procedure is recommended:
Set the Dark Time (see 
previous page) to a value 
appropriate to the glasses or 
Z-screen, say 1000 µS.
Adjust the Sync Delay time to 
eliminate ghosting and achieve 
a smooth greyscale.
Repeat steps 1 and 2 until the 
best result is obtained.
 Use this if the left and right 
images appear to be swapped.
1.
2.
3.
3D Sync Delay
The sync signal from the 3D server will be in phase with the frames gene\
rated by 
its graphics card. However, to compensate for processing delays in the projector, 
this control is provided to introduce a delay to the sync output signal \
sent to the 
Z screen or 3D glasses.
Press  and   to select Sync Delay.
 
Press  and   to adjust the slider (-1500 to +1500 µS).
3D Sync Source
Press  and   to select 3D Sync Source.
 Press  and   to select from:
External
Internal
3D Sync Output polarity
Press  and   to select 3D Sync Output Polarity.
 Press  and   to select from:
Positive
Negative
•
•
•
Setup menu, 3D Setup continued
Incoming 
video
Incoming 
sync signal
Video signal with 
processing delays (and   dark time adjustment)
Sync output signal after  delay adjustment 
						

							Page 4.58 Rev C  April 2011
4. Controlling the projector Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Output Shuttering (Frame rate Multiplication)
If the 3D video is available only at low frame rates, it will be necessa\
ry to multiply 
the frame rate to obtain a flicker-free image. For example, a 60Hz frame rate can be 
doubled to 120Hz, or a 48Hz frame rate could be tripled to 144Hz.
Press 
 and   to select Output Shuttering.
 Press  and   to select from:
x1
x2
x3
x2 Example
•
Setup menu, 3D Setup continued
Notes
 3D may not be present on some 
models
 None of the 3D options are 
avialable unless  3D Mode is set 
to Consumer or Professional.
  WUXGA models only: 
The maximum Frame Rate 
Multiplication available for 
WUXGA and UXGA images is 
x2.
L1
R1 L2
R2
L1
L1
R1R2
L2 L3
R2
R1
L3
L2
INOUt