Digital Projection Titan Reference 1080p 3d, Dual 3d, Titan 1080p 3d, Dual 3d Ultra Contrast, Titan Dual Fastframe User Manual

							Rev C  April 2011 Page 5.27
Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual 5. Userware
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview .
Notes
 The Connect page is available 
only on the Standalone version 
of the Userware.
  The Userware can be used to 
control only one projector at a 
time, and only one instance can 
be running at one time.
  The Connect page can be 
used to switch control between 
multiple projectors.
  More than one computer can be 
used to control more than one 
projector on the same network.
Connect page
To see the Connect page, click on Connect.
Refresh
Click on Refresh  to search the network for projectors.
 Any projectors previously connected, that are now no longer online, will be 
marked Unreachable.
Connect
To connect to a projector, click on one of the  LAN IP addresses in the list, then 
click on Connect.
or
  Double click on a LAN IP address.
Any projector previously connected will be disconnected, and the Userware will 
connect to the new projector.
  The LAN IP address of the projector that is connected will be highlighted.
 Projector Connected will be shown at the top left of all pages, together with the 
projector’s Serial No and Model.
Disconnect
To disconnect from the projector, click on Disconnect
 Projector Disconnected will be shown at the top left.
•
•
•
• 
						

							Page 5.28 Rev C  April 2011
5. Userware Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual
 For important information about how Input 8 is used, see INPUT 8 in the Notes column, and also Section 4, Overview . 
						

							Rev C  April 2011 Page 6.1
6. Maintenance
Contents
Changing the lamp module ........................................................................\
......................................6.2
Changing the air filters ........................................................................\
..............................................6.2
Cleaning ........................................................................\
........................................................................\
6.3
Projector ........................................................................\
..................................................................6.3
Lens ........................................................................\
........................................................................6.3 
						

							Page 6.2 Rev C  April 2011
6. Maintenance Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual
Changing the air filters
The air filters should be changed only by qualified and authorised service 
personnel.
Contact your Digital Projection Dealer.
•
•
Changing the lamp module
The lamp module should be changed only by qualified and authorised service 
personnel.
Contact your Digital Projection Dealer.
•
•
Notes
 
The lamp and filters in this 
projector should be changed 
ONLY by authorised and 
qualified service personnel.
 Always allow the lamp to cool 
for 5 minutes before: 
- disconnecting the power  
- moving the projector.
  At the end of life, the lamp 
will not strike, and the Lamp 
Indicator on the control panel 
will show red. (Typical lamp life 
is 2000 hours)
 Do not use the lamp for more 
than 2000 hours, as this may 
cause serious lamp failure, 
damage the lamp module 
and cause extra cost on 
replacement. 
 HID lamps produce high 
intensity light. Do not look 
directly at the light coming 
from the lamp housing or the 
lens.
  The filters should be changed 
at the same time as the lamp is 
changed.
 The air filters should be 
changed regularly:
  - In a clean environment such 
as an office, change after 2000 
hours, at the same time as the 
lamp is changed.
 - In a dusty or smoky 
environment such as a theatre 
or public area, more frequent 
changes may be necessary. 
						

							Rev C  April 2011 Page 6.3
Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual 6. Maintenance
Notes
 Always allow the lamp to cool 
for 5 minutes before:
 - disconnecting the power  
- moving the projector.
  Never use strong detergents 
or solvents such as alcohol 
or thinners to clean the 
projector and lens.
Cleaning
Turn the projector off before cleaning.
Projector
Clean the cabinet periodically with a damp cloth. If heavily soiled, use a mild 
detergent.
Lens
Use a blower or lens paper to clean the lens, taking care not to scratch the glass. 
						

							Page 6.4 Rev C  April 2011
6. Maintenance Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual 
						

							Rev C  April 2011 Page 7.1
7. Appendix
Contents
Troubleshooting ........................................................................\
..........................................................7.2
Specifications ........................................................................\
..............................................................7.4
Part numbers ........................................................................\
............................................................7.4
Optical ........................................................................\
.....................................................................7.4
Electrical ........................................................................\
..................................................................7.5
Physical ........................................................................\
...................................................................7.5
Lens Data ........................................................................\
................................................................7.6
Dimensions ........................................................................\
..................................................................7.8
Input modes supported by inputs 1-7 ........................................................................\
....................7.9
Input connections ........................................................................\
.....................................................7.10
1. RGB1 input ........................................................................\
.........................................................7.10
2. RGB2 input ........................................................................\
.........................................................7.10
3. DVI-D Single input ........................................................................\
................................................7.1 1
4. SDI input ........................................................................\
............................................................7.12
5. Composite video input ........................................................................\
.........................................7.12
6. S-Video input ........................................................................\
......................................................7.12
7. Component video input ........................................................................\
........................................7.12
8. DVI-D Single/Dual/Twin input ........................................................................\
...............................7.13
Control connections ........................................................................\
................................................7.14
Wired Remote control connection ........................................................................\
.............................7.14
LAN connection ........................................................................\
......................................................7.14
Crossed cable ........................................................................\
......................................................7.14
3D sync ........................................................................\
.................................................................7.15
Serial control input ........................................................................\
..................................................7.15
Null-modem cable ........................................................................\
.................................................7.15
Serial port settings ........................................................................\
................................................7.15
Remote communications protocol ........................................................................\
.......................7.16
Introduction ........................................................................\
............................................................7.16
Message Structure ........................................................................\
..................................................7.16
Operation Messages ........................................................................\
.............................................7.17
Enhanced Messages ........................................................................\
.............................................7.18
Operation Command examples ........................................................................\
................................7.19
Power  (0102) ........................................................................\
.....................................................7.19
Source  (3702) ........................................................................\
....................................................7.20
Brightness (E502) ........................................................................\
................................................7.21
Contrast (E602) ........................................................................\
...................................................7.22
Shutter  (CF02) ........................................................................\
...................................................7.23
Quick Reference chart ........................................................................\
.............................................7.24 
						

							Page 7.2 Rev C  April 2011
7. Appendix Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual
Troubleshooting
problempossible solutions
The projector will not power up. Check that the mains plug is plugged in and that the mains supply is switched on.
Check any external fuses or breakers.
The projector shuts down after it has 
been in use for some time. The projector may be overheating. Check that the air inlets and outlets are clear 
of any obstruction. Check that the air filter is clean, and if it is dirty
, fit a new one.
See section 1. Introduction, Getting to know the projector
No image is displayed. Check the lamp indicators on the control panel. If both indicators are red, then 
both lamps are faulty.
See section 5. Maintenance, Changing the lamp
Check that the input source is switched on and connected to the projector 
correctly.
Check that the correct image source is selected.
See section 4. Controlling the projector, Using the control keys and Input 
menu
Check that the brightness and contrast settings are set correctly .
See section 4. Controlling the projector, Picture menu
The projector may be overheating. Check that the air inlets and outlets are clear 
of any obstruction. Check that the air filter is clean, and if it is dirty, fit a new one.
The image does not fit the screen 
correctly. Check that the correct lens is being used for the combination of screen size and 
projection distance, and that the zoom is adjusted correctly.
See section 2. Installation, Choosing a lens
Check the image size settings.
See section 4. Controlling the projector, Picture or Geometry menus
Uneven image quality. Check that the projector is parallel to the screen.
Check that the screen is flat, and securely mounted.
Low image brightness. Check that the FastFrame Dark Time is not set too high.
See section 4. Controlling the projector, Setup menu
Poor colour depth reproduction. Colour depth is 8 bits using Single or Dual DVI inputs. If using Twin DVI inputs for 
greater colour depth, check that both source cables are connected correctly.
If using 3D mode, check the settings of the Dark Time and Sync Delay controls.
See section 4. Controlling the projector, Setup menu 
						

							Rev C  April 2011 Page 7.3
Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual 7. Appendix
problempossible solutions
Severe flicker or motion artifacts If not using a 3D signal, check that 3D Enable is turned Off,
See section 4. Controlling the projector, Setup menu
3D images swapped Check that Left/Right swap is selected correctly in the 3D server .
Check the Frame Dominance and Sync Delay settings in the 3D menu.
Check the Sync Source setting in the 3D menu.
See Section 4. Controlling the projector, Setup menu .
3D image ghosting Check the Dark Time and Sync Delay settings in the 3D menu.
See Section 4. Controlling the projector, Setup menu .
No OSD (on-screen-display) visible  Check the OSD On button on the remote control or keypad has been pressed.
The OSD does not work when Input 8 is selected.
See Section 4. Controlling the projector, Controlling the projector when 
Input 8 is being used.
Projector does not respond to control 
commands from a computer. Check that the LAN or serial cable is connected correctly.
See this section 7. Appendix, Connections
If using a LAN, check that the address setting is made correctly
.
See section 4. Controlling the projector, Network menu
If using a serial cable, check that the baud rate is set correctly .
See this section 7. Appendix, Connections
Check that the correct control codes are being used.
See Serial communications protocol  (available from Digital Projection)
Projector does not respond to control 
commands from the remote control. If you are using a cable, check that the cable is connected properly at both ends, 
that the cable is not damaged and that the cable is no longer than 50m (150ft).
If you are not using a cable, check that the infra red windows at the front and rear 
of the projector are not obstructed. Check that the cable is disconnected from 
the projector, as this disables the infra red. Check that the batteries are in good 
condition.
Check that the address setting on the remote control is set either to zero, or to the 
same as the projector.
See section 4. Controlling the projector, Communication menu
In the event that this troubleshooting guide has not solved the problem,\
 
then contact your Digital Projection dealer or service centre. 
						

							Page 7.4 Rev C  April 2011
7. Appendix Digital Projection TITAN 1080p 3D, Dual 3D. Ultra Contrast User Manual
Specifications
Part numbers
Projector
1080p 3D  109-583
1080p 3D Ultra Contrast 109-322
1080p Dual 3D 109-323
1080p Dual 3D Ultra Contrast 109-324
1080p Dual Fast Frame 109-362
Rigging frame 107-956
Power cable 10A, Europe 102-163
Power cable 13A, North America 102-165
Power cable 10A, United Kingdom 102-180
Remote control 105-023
4x AAA batteries 105-922
3D Sync cable 109-697
Lens clamp 111-256
User manual on CD 105-923
Important Information 108-467
Lenses High Brightness High Contrast
0.67 : 1 fixed lens  105-607 107-195
1.12 : 1 fixed lens (3 - 15m)  105-608 105-608
1.12 : 1 fixed lens (1.2 - 2m)  105-609 105-609
1.16 - 1.49 : 1 zoom lens  109 236 109-359
1.39 - 1.87 : 1 zoom lens  105-610 107-196
1.87 - 2.56 : 1 zoom lens  105-611 107-197
2.56 - 4.16 : 1 zoom lens  105-612 107-198
4.16 - 6.96 : 1 zoom lens  105-613 107-199
6.92 - 10.36 : 1 zoom lens  109-235 109-358
Optical
Digital Light Processor 3 x 0.95” Texas Instruments DMD™, resolution 1920 x 1080 pixels
Pixel fill factor  87%
Lamp life (typical)  2000 hours per lamp
Colour temperature Native: 7500K (±1000K), White balance adjustment: 3000K - 10000K