Digital Projection Titan Pro Series III User Guides

Digital Projection Titan Pro series III  A TOUR OF THE MENUS  Operating Guide
Page Op_11Rev A   May 2012
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
Main MenuGlobal SettingsInput Configuration
 All these settings will remain as set 
in this menu, regardless of which 
input is being used.
Input Configuration
These menus allow adjustment of various technical parameters specific to\
 each of the signal inputs, regardless of which input is being used....

Digital Projection Titan Pro series III  A TOUR OF THE MENUS  Operating Guide
Page Op_12Rev A   May 2012
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
Main MenuGlobal SettingsLamp
 The number of lamps is dependent 
on the projector model. Single lamp 
models will have no Lamp menu.
 Not all models have a lamp power 
setting.
Main MenuGlobal SettingsLens
 Each time a lens is fitted to 
the projector, the calibration 
procedure must be carried out.
  (Use this...

Digital Projection Titan Pro series III  A TOUR OF THE MENUS  Operating Guide
Page Op_13Rev A   May 2012
On Screen Display
Select a display Language from the drop-down list.
The menus will disappear if no buttons are pressed within the Timeout selected from the drop-down list. If you want the menus to stay 
on screen permanently, then select Infinite.
Select a Position from the drop-down list.
If you do not want projector status messages to be displayed, for instan\
ce: , then set Messaging to Off.
•
•...

Digital Projection Titan Pro series III  A TOUR OF THE MENUS  Operating Guide
Page Op_14Rev A   May 2012
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
Main MenuGlobal SettingsNetwork
 Any new settings will not be effective 
until the projector has been turned 
off, then back on again.
Main MenuGlobal SettingsFactor y Defaults
 Do NOT do this unless you are 
sure that you want to restore 
ALL the current settings to their 
factory defaults.
Network
The fields...

Digital Projection Titan Pro series III  A TOUR OF THE MENUS  Operating Guide
Page Op_15Rev A   May 2012
Picture
Brightness, Contrast, Gamma, Hue, Saturation
Set the slider or select from the drop-
down list as required, to improve the 
quality of the image.
 You can also press ,  or  
on the remote control.
Black Level Offset
Set this to 0 IRE or 7 IRE as required.
•
•
Input Settings Menu
The Input Settings are those that affect ONLY the input being displayed. When a new input mode (video or graphics...

Digital Projection Titan Pro series III  A TOUR OF THE MENUS  Operating Guide
Page Op_16Rev A   May 2012
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
Main MenuInput SettingsColour Trim
 When a new input mode is detected 
(eg NTSC, HDTV 1080p, SVGA etc), 
all the Input Settings are saved so 
that they can be recalled next time 
that input mode is displayed.
Colour Trim
Set the sliders as required.• 

Digital Projection Titan Pro series III  A TOUR OF THE MENUS  Operating Guide
Page Op_17Rev A   May 2012
Geometr y
Set Aspect Ratio to choose between Source, Fill, Fill & Crop, Anamorphic and 
Theatrescope.
Anamorphic: Some devices (eg certain DVD players) pack a 16:9 image into a 4:3 
aspect ratio.  In such cases to display the image correctly, choose the Anamorphic 
aspect ratio.
TheatreScope: The 2.35:1 source image is displayed using the full area of the DMD. 
This is then stretched to 2.35:1 by the...

Digital Projection Titan Pro series III  A TOUR OF THE MENUS  Operating Guide
Page Op_18Rev A   May 2012
Set the H Position and V Position sliders as required.
Set the Overscan slider to compensate for noisy or badly defined image edges.
Pan/Scroll/Zoom
Set Enable to On or Off.
Use Setting to choose:
Global, in which case these settings will be applied to all input signals,
or Per Mode, in which case these settings will be applied only to the current input\
 signal.
Set the Pan, Scroll and Zoom sliders...

Digital Projection Titan Pro series III  A TOUR OF THE MENUS  Operating Guide
Page Op_19Rev A   May 2012
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
Main MenuInput Settings3D
Main MenuInput Settings3DGlasses Settings
 Set the Dark Time to the value 
appropriate to the glasses or Z-
screen.
  Adjust the Sync Offset to eliminate 
ghosting and achieve a smooth 
greyscale.
3D Menu
Set 3D Enable to On or Off as required.
Set Source Dominance to Left or Right to...

Digital Projection Titan Pro series III  A TOUR OF THE MENUS  Operating Guide
Page Op_20Rev A   May 2012
System Menu
Use the Shutter Open and Shutter Close commands as required.
Use the Power Off  command to set the projector into Standby mode.
•
•
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
Main MenuSystem
 The Power On command has no 
function when seen on the projector 
OSD.
  However, it can be used from the 
Web Configuration application 
described at...