Digital Projection Titan Pro Series III User Guides

Digital Projection Titan Pro series III  USING THE REMOTE CONTROL AND THE CONTROL PANEL  Operating Guide
Page Op_1Rev A   May 2012
Using the Remote Control and the Control PanelNotes
 For full details of how to use the 
menu system, see later in this guide.
 When you press any of the Lens 
control buttons, the Transmit 
indicator will stay illuminated for 10 
seconds, or until you press Exit.
 Each time a lens is fitted to 
the projector, the calibration 
procedure must be carried out.
  (see the...

Digital Projection Titan Pro series III  USING THE MENUS  Operating Guide
Page Op_2Rev A   May 2012
Using the Menus
Use the buttons on the projector control panel or on the remote control,\
 to access the menu system.
To open or close the on-screen display (OSD), press .
Menus and sub-menus
To open a sub-menu, select it using  and, then press .
To return to the previous menu, press .
Drop-down lists
 To use a drop-down list, press , select an item using  and, then press  again or press to exit without...

Digital Projection Titan Pro series III  USING THE MENUS  Operating Guide
Page Op_3Rev A   May 2012
Sliders
 To use a slider, press  andto adjust it.
Commands
 To use a command, press . In the example below, press  to confirm, or press to cancel.
•
•
Notes
 Some menu options and controls 
may not be available due to settings 
in other menus. These will be 
greyed-out on the actual menu. 

Digital Projection Titan Pro series III  USING THE MENUS  Operating Guide
Page Op_4Rev A   May 2012
Editing fields
Some features require a text or numeric field to be edited.
To edit a field, first select it using  and, then press .
Use  andto move the green highlight to the digit or character which is to be cha\
nged, then use  and, to adjust it.
Use  andto select the next digit or character... etc.
Press  to accept the new value, or press to exit without changing.
•
•
•
•
Notes
 Some menu options and...

Digital Projection Titan Pro series III  A TOUR OF THE MENUS  Operating Guide
Page Op_5Rev A   May 2012
A Tour of  the Menus
Main Menu
Input Selection
Select an input source from the drop-down list.
Test Pattern
Set Input Selection to Test Pattern, then select a test pattern from the drop-down list.
Global Settings
Global Settings are those that affect the whole projector, regardless of which input is being used or what kind of image is being\
 displayed.
More information about this menu can be found...

Digital Projection Titan Pro series III  A TOUR OF THE MENUS  Operating Guide
Page Op_6Rev A   May 2012
Global Settings Menu
Global Settings are those that affect the whole projector, regardless of which input is being used or what signal type is being d\
isplayed.
Projector
Orientation
Depending on how the projector is mounted, select the appropriate settin\
g from the drop-down list
Latency
Affects interlaced sources only. For fastest response, the Minimal setting gives minimum frame delay. For...

Digital Projection Titan Pro series III  A TOUR OF THE MENUS  Operating Guide
Page Op_7Rev A   May 2012
Picture
These settings in the Global Picture Menu affect all images, regardless of which input is being used or what signal \
type is being displayed.
Colour Mode
Select one of the preset Colour Modes from the drop-down list.
Gamma
Select a Gamma setting from the drop-down list.
•
•
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
Main MenuGlobal...

Digital Projection Titan Pro series III  A TOUR OF THE MENUS  Operating Guide
Page Op_8Rev A   May 2012
Edge Blend
When several projectors are used to create a large tiled image, the edge\
s need to be blended to avoid the overlaps appearing brighter than 
the rest of the image. The Edge Blend menu is available only when Configuration in the Projector menu is set to Edge Blend.
Array Width and Height
Set this to the total number of projectors in the array. None of the other options are available until...

Digital Projection Titan Pro series III  A TOUR OF THE MENUS  Operating Guide
Page Op_9Rev A   May 2012
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
Main MenuGlobal SettingsPIP
 This menu is available only when 
Configuration in the Projector 
menu is set to PIP.
 PIP, PAP and POP are NOT 
possible when Input is set to Test 
Pattern.
 In these examples, the flower is the 
main image, and the window is the 
sub-image, shown at the Medium 
size setting.
 The...

Digital Projection Titan Pro series III  A TOUR OF THE MENUS  Operating Guide
Page Op_10Rev A   May 2012
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
Main MenuGlobal SettingsAdvanced Geometr y
 See also Geometr y in the Input 
Settings menu, later in this guide.
 Which settings are available in these 
menus depends on:
  - which Mode is selected in the first 
drop-down list
 - and the Pincushion/Barrel slider 
can be used on its own, or in 
conjunction with...