Digital Projection Titan Pro Series III User Guides

Digital Projection Titan Pro series III  POSITIONING THE SCREEN AND PROJECTOR  Installation and Quick-Start Guide
Page Inst_7Rev A   May 2012
Redirecting the Air Outlet Duct
The duct can be set to blow upwards whether the projector is in desktop \
or ceiling mode, as shown below.
Unscrew the four screws securing the rear cover, then remove the cover.
Working from the back of the cover panel,  unscrew the two screws securin\
g the duct
Turn the duct through 180°, refit the two screws, then refit the...

Digital Projection Titan Pro series III  FITTING THE LENS  Installation and Quick-Start Guide
Page Inst_8Rev A   May 2012
Lens 
release 
lever
Notes
 Always allow the lamp to cool for 
5 minutes before:
  - disconnecting the power 
- moving the projector
 The lens release lever should 
always be set to the locked 
position to prevent the lens from 
falling out.
 Do not place the projector with its 
front panel down on a surface, as 
this may damage the lens or the 
lens release lever.
 Each time a lens...

Digital Projection Titan Pro series III  OPERATING THE PROJECTOR  Installation and Quick-Start Guide
Page Inst_9Rev A   May 2012
Operating the Projector
Switching the Projector On
Connect the power cable between the mains supply and the projector. Switch on at the switch next to the power connector.
Wait until the self-test has completed and the standby indicator on the p\
rojector control panel shows amber. The lamp will be off and the 
projector will be in STANDBY mode.
Press  on the remote control or...

Digital Projection Titan Pro series III  OPERATING THE PROJECTOR  Installation and Quick-Start Guide
Page Inst_10Rev A   May 2012
Adjusting the Lens
The lens can be adjusted using the Lens Menu, which is available from the Global Settings Menu, or:
Zoom
 Press  followed by  and to adjust the size of the image on the screen.
When the adjustment is finished, press .
Focus
 Press  followed by  and to adjust the focus.
When the adjustment is finished, press .
Shift
 Press  followed by , , andto adjust the...

Digital Projection Titan Pro series III  OPERATING THE PROJECTOR  Installation and Quick-Start Guide
Page Inst_11Rev A   May 2012
Switching the Projector Off
Press   on the remote control or the control panel, and hold for 3 seconds, to \
switch the projector OFF. The power indicator on the 
control panel will show amber, the lamp will be off and the projector will be in STANDBY mode.
Switch off at the switch next to the power connector. Disconnect the power cable from the projector.
•
•
Notes
 Always...

Rev A   May 2012
Titan Pro series III
High Brightness Digital Video Projector
CONNECTION GUIDE
BOOK CONTENTS
CONNECTION GUIDE
Signal Inputs and Outputs
Rear Connection Panel
VGA (input 1)
HDMI (input 2)
DVI (input 3)
SPDIF
3G-SDI (input 4)
CVBS1 (Composite video BNC) (input 5) 

Digital Projection Titan Pro series III  CONTENTS  Connection Guide
Rev A   May 2012
CONTENTS
Signal Inputs and Outputs ..........................................................Conn_1
Rear Connection Panel ......................................................................Conn_1
VGA (input 1)  ........................................................................\
...............Conn_1
HDMI (input 2)  ........................................................................\
.............Conn_1
DVI...

Digital Projection Titan Pro series III  SIGNAL INPUTS AND OUTPUTS  Connection Guide
Page Conn_1Rev A   May 2012
Signal Inputs and Outputs
Rear Connection Panel
VGA (input 1)
Use Auto Setup in the Input Settings/Picture/VGA Setup menu. For more settings, 
see the Operating Guide.
HDMI (input 2)
For settings, see the Operating Guide.
DVI (input 3)
Analog or Digital DVI-I
Set DVI-I Port in the Global Settings/Input Configuration menu to choose between 
Analog and Digital. For more settings, see the...

Digital Projection Titan Pro series III  SIGNAL INPUTS AND OUTPUTS  Connection Guide
Page Conn_2Rev A   May 2012
Side Connection Panel
MAIN/DVI (input 9)
Single or Dual Link DVI-D input
SUB/HDMI (input 10)
Single HDMI 1.4 input (using an adaptor), or
Single or Dual Link DVI-D input
 For information about 3D video, see the next page.
Differences between the two Connection Panels
Inputs 9 and 10 have been designed to give a very high bandwidth digital\
 video path, free of 
the limitations inherent to...

Digital Projection Titan Pro series III  SIGNAL INPUTS AND OUTPUTS  Connection Guide
Page Conn_3Rev A   May 2012
3D Connections
3D sources up to 60Hz requiring frame doubling and left/right interleaving
Connect to any of the Inputs on the Rear Connection Panel.
Set  3D Type in the Input Settings/3D Settings menu to Auto, except when the 
projector has problems selecting between Sequential, Frame Packing, Top-and-
Bottom and Side-by-Side (Half).
3D sources above 60Hz not requiring frame doubling
Connect...