Digital Projection Showlite 3000sx, 4000gv User Manual

12 - S-VIDEO Audio Input Jacks
These RCA connections are for the left and right audio inputs for stereo sound from
equipment connected to the S-VIDEO input. The left input also acts as a monoaural
audio input. 
13 - AUDIO OUT Jacks
These RCA connections are used to output sound from the currently selected input
source.
Right Terminal Panel - SHOWlite 4000gv
The Right Terminal Panel located on the front of the projector provides all the
required connections for input signal.
1 - DVI Connector
This...

3 - RGB 2 Connector
This Mini D-Sub 15-Pin connection is used to connect RGB equipment (e.g. your
PC, Macintosh or DVD player). When using a Y/Cb/Cr output, the optional
Component V cable should be used.
4 - RGB 2 Audio Input Jacks
These RCA connections are for the left and right audio inputs for stereo sound from
RGB equipment connected to the RGB 2 Input. The left input also acts as a
monoaural audio input. 
5 - MONITOR OUT Connector
This Mini D-Sub 15-Pin connection is used to loop your RGB or DVI...

11 - S-VIDEO Input Connector
A Mini DIN 4-Pin connection for connection of an S-Video source such as a VCR
or Laser Disc Player.
12 - S-VIDEO Audio Input Jacks
These RCA connections are for the left and right audio inputs for stereo sound from
equipment connected to the S-VIDEO input. The left input also acts as a monoaural
audio input. 
13 - AUDIO OUT Jacks
These RCA connections are used to output sound from the currently selected input
source.
Remote Control
All the functions of the projector can be...

When using infra red operation the remote control has an effective range of about
7m (23 feet) and at an angle of 30¡ above, below, to the left and to the right of the
remote control sensors located at the front, rear and on both sides of the projector.
The remote control should not be exposed to heat, steam, water or any other 
liquid. If the remote control gets wet, wipe it dry immediately. 
When remote control buttons are pressed and held down the main unit function
keys may not operate.
Direct...

Installation Guidelines...................................................... BÑ1
Screen Requirements................................................... B
Ñ1
Positioning the Projector  .............................................. B
Ñ4
Installation ....................................................................... BÑ8
Attaching the Lens Hood Cap .................................... BÑ8
Lens Installation .......................................................... BÑ8
Basic Operation...

System Installation
INSTALLATION
LBV00073; Revision A - 11/01/2002 

This installation section explains how to install the projector for optimum results.
To do this, it is necessary to determine the following:
1. The type of screen and whether front or rear projection is to be used.
2. The projector location and therefore the type of lens to be used.
3. The method of mounting for the projector.
4. The type of input source to be used with the projector.
Screen Requirements
As virtually all commercially available screens will give a pleasing image you
should choose...

For optimum viewing, the screen should be a flat surface perpendicular to the floor.
The bottom of the screen should be 1.2m (4 feet) above the floor and the front row
of the audience should not have to look up more than 30¡ to see the top of the
screen (see opposite).
The distance between the front row of the audience and the screen should be at least
twice the screen height and the distance between the back row and the screen should
be a maximum of 8 times the screen height. The screen viewing area...

BÑ3
System Installation
INSTALLATION
LBV00073; Revision A - 11/01/2002
SCREEN
60°2H
8H
VIEWING AREA
2H
1.2m  (4 Ft)30°
H 

Positioning the Projector
Correct positioning of the projector is essential to achieve the best results. Before
deciding on the final location of the projector please ensure you read the following 
information very carefully.
The projector must be situated in a clean, dry environment and away from direct
sunlight or heat. Make sure you locate the projector so that the air inlets and 
outlets for the cooling system are not obstructed.
When positioning the projector always carry it by the retractable...