Digital Projection Projector HIGHlite 660 3D Series User Manual

							page 13
Installation and Quick-Start Guide
POSITIONING THE SCREEN AND PROJECTOR
Adjusting the optional rigging frame
1. Remove the four adjustable feet.
2. Secure the rigging frame to the projector, as 
shown here, making sure that the rigging frame is 
in its upright position and the cable attachments 
are at the top. Three screws secure each of the 
adjuster brackets to a corner handle.
3. Adjust pitch, roll and yaw as required.
1 Vertical adjuster
2 Horizontal adjuster
3 Frame couplings
4 Fixing screws
Notes
 Always allow the projector to 
cool for five minutes before 
disconnecting the power or 
moving the projector.
 Ensure that there is at least 
30 cm (12 in.) of space between 
the ventilation outlets and any 
wall, and 10 cm (4 in.) on all other 
sides.
 Do not stack more than three 
projectors.
 Do not place heavy objects on top 
of the projector chassis. Only the 
chassis corners and the rigging 
frame are capable of withstanding 
the weight of another projector.
 Do not place the projector with its 
front panel down on a surface, as 
this may damage the lens or the 
lens release lever.
 Backup safety chains or wires 
should always be used with 
ceiling mount installations.
 When positioning the projector, 
do not exceed the roll limits 
as this may cause serious 
lamp failure, damage the lamp 
module and cause extra cost 
on replacement. For more 
information, see  Tilting the 
projector earlier in this guide.
4
12
3
   
Digital Projection HIGHlite 660 3D Series 
Rev E Februar y 2015  
						

							page 14
Installation and Quick-Start Guide
CHANGING THE LENS
Changing The Lens
Inserting a new lens
1. Remove the six screws 1 securing the front cover to the body of 
the projector.
2. Remove the front cover 2 from the projector.
3. Remove the lens from its packaging and remove the two protective 
caps from the front and back of the lens.
4. Insert the lens 3 into the lens aperture, making sure that the plug 
on the zoom drive mechanism lines up with the socket 4 on the 
right of the lens aperture.
5. Push the lens in firmly as far as it will go.
6. Rotate the lens clockwise as far as it will go.
7. Replace the front cover and secure it with the six screws.
Notes
 Before changing the lens, 
always make sure the projector 
is switched off and fully 
disconnected from its power 
supply.
 Always allow the lamp to cool for 
five minutes before:
  - disconnecting the power 
- moving the projector
 When changing the lens, avoid 
using excessive force as this may 
damage the equipment.
 Avoid touching the surface of the 
lens as this may result in image 
impairment.
  Take care to preserve the original 
lens packaging and protective caps 
for future use.
2
1
43
   
Digital Projection HIGHlite 660 3D Series 
Rev E Februar y 2015  
						

							page 15
Installation and Quick-Start Guide
CHANGING THE LENS
Removing the lens
1. Remove the six screws 1 securing the front cover to the body of 
the projector.
2. Remove the front cover 2 from the projector.
3. Push down the lens holder tab 3.
4. Rotate the lens anti-clockwise
5. Pull the lens forward to remove it from the lens aperture.
2
1
3
Notes
 Before changing the lens, 
always make sure the projector 
is switched off and fully 
disconnected from its power 
supply.
 Always allow the lamp to cool for 
five minutes before:
  - disconnecting the power 
- moving the projector
 When changing the lens, avoid 
using excessive force as this may 
damage the equipment.
 Avoid touching the surface of the 
lens as this may result in image 
impairment.
  Take care to preserve the original 
lens packaging and protective caps 
for future use.
   
Digital Projection HIGHlite 660 3D Series 
Rev E Februar y 2015  
						

							page 16
Installation and Quick-Start Guide
OPERATING THE PROJECTOR
Operating The Projector
Switching the projector on
1. Connect the power cable between the mains supply and the projector. Switch on at the switch next to the power connector.
2. Wait until the self-test has completed and the standby indicator on the p\
rojector control panel shows amber. The lamp will be off and the 
projector will be in STANDBY mode.
3. Press ON on the remote control or the control panel and hold for three seconds, \
to switch the projector ON. The power indicator on the 
control panel will show green, the lamp will light and the shutter will \
open.
Switching the projector off
1. Press OFF on the remote control or the control panel, and hold for three seconds.\
 The power indicator on the control panel will show 
amber, the lamp will go out and the cooling fans will run for a short time un\
til the projector enters STANDBY mode.
2. If you need to switch the projector off completely, switch off at the mains power switch next to the power connector and then disconn\
ect 
the power cable from the projector
Notes
 The self-test is running when all the 
LEDs on the control panel are lit.
 Use only the power cable 
provided.
 Ensure that the power outlet 
includes a ground connection as 
this equipment MUST be earthed.
 Handle the power cable carefully 
and avoid sharp bends. Do not 
use a damaged power cable.
 Always allow the lamp to cool for 
five minutes before:
  - disconnecting the power 
- moving the projector
   
Digital Projection HIGHlite 660 3D Series 
Rev E Februar y 2015  
						

							page 17
Installation and Quick-Start Guide
OPERATING THE PROJECTOR
Selecting an input signal or test pattern
Input signal
1. Connect an image source to the projector.
2. Switch to the input you want to display:
• Press one of the input buttons on the remote control, or
• Open the On-screen display (OSD) by pressing MENU. Select an input signal from the Input 
Selection menu, using the UP and DOWN arrow buttons, then press OK.
Test pattern
To display a test pattern:
1. Open the OSD by pressing MENU.
2. Select Test Pattern from the Input Selection menu, using the UP and DOWN arrow buttons, then 
press OK.
3. Select a pattern from the Test Pattern menu, using the UP and DOWN arrow buttons, then press OK.
4. Close the OSD by pressing MENU again.
Notes
 For full details of how to use the 
controls and the menu system, see 
the Operating Guide .
 For a full list of supported input 
signals, see  Appendix C: 
Supported  Signal Input Modes  in 
the Reference Guide.
  If the projector is switched off while 
in TEST PATTERN mode, it will still 
be in TEST PATTERN mode when 
switched on again.
   
Digital Projection HIGHlite 660 3D Series 
Rev E Februar y 2015  
						

							page 18
Installation and Quick-Start Guide
OPERATING THE PROJECTOR
Adjusting the lens
The lens can be adjusted using the Lens menu, or:
Zoom
• Press ZOOM, then use the UP and DOWN arrow buttons on the keypad or remote control to adjust the size of the\
 image on the screen. 
When the adjustment is finished, press EXIT.
Focus
• Press FOCUS, then use the UP and DOWN arrow buttons on the keypad or remote control to adjust the focus. When\
 the adjustment is 
finished, press EXIT.
Shift
• Press SHIFT, then use the UP, DOWN, LEFT and RIGHT arrow buttons on the keypad or remote control to adjust the position of\
 the 
image on the screen. When the adjustment is finished, press EXIT.
Notes
 When any of the three lens 
adjustment buttons is pressed, 
the blue Transmit indicator on 
the remote control will light for 10 
seconds:
  After 10 seconds, if no adjustment 
has been made, the indicator will go 
out and the lens adjustment button 
must be pressed again to resume 
adjustment.
  To end the adjustment before 10 
seconds has elapsed, press the 
EXIT button.
  All other adjustments will be locked 
out until the lens adjustment is 
ended.
   
Digital Projection HIGHlite 660 3D Series 
Rev E Februar y 2015  
						

							page 19
Installation and Quick-Start Guide
OPERATING THE PROJECTOR
Adjusting the image
Orientation
• This can be set from the Setup menu.
Select the orientation which suits the positioning of the projector.
Keystone
• This can be set from the Geometr y menu.
Picture
• Settings such as Brightness and Contrast can be set from the Image menu.
• You can also set Brightness, Contrast or Gamma by pressing BRI, CON or GAMMA on the remote 
control.
Notes
Main MenuSetup
 Lens shift works from the audience’s 
perspective, regardless of projector 
orientation. For example, 
SHIFT UP 
moves the image toward the ceiling 
in both Desktop and Ceiling mode.
Main Menu Geometr y
Main Menu Image
 For full details of how to use the 
controls and the menu system, see 
the Operating Guide .
   
Digital Projection HIGHlite 660 3D Series 
Rev E Februar y 2015  
						

							Installation and Quick-Start Guide
   
Digital Projection HIGHlite 660 3D Series 
This page is intentionally left blank.  
						

							CONNECTION GUIDE4 
Rev E Februar y 2015 
HIGHlite 660 3D Series
High Brightness Digital Video Projector  
						

							Connection Guide
IN THIS GUIDE
IN THIS GUIDE
Signal Inputs And Outputs ........................................................................\
.....23
Analog inputs  ............................................................................................................23
Digital inputs and outputs ........................................................................................24
Low latency inputs ....................................................................................................25
DVI connection example ...........................................................................................26
EDID on the DVI and VGA inputs .............................................................................27
Using HDMI/DVI switchers with the projector ........................................................27
3D connections .........................................................................................................28
3D sources up to 60Hz requiring frame doubling and left/right interleavi\
ng ...................28
3D sources above 60Hz not requiring frame doubling ....................................................28
Dual Pipe 3D .....................................................................................................\
..............28
3D Sync ......................................................................................................................29
3D Sync in .....................................................................................................\
..................29
3D Sync out  ....................................................................................................\
................29
Control Connections ........................................................................\
................30
HDBaseT/LAN ............................................................................................................30
Wired remote control  ................................................................................................30
Service port ...............................................................................................................31
RS232 .........................................................................................................................31
Control port  ...............................................................................................................31
LAN connection examples .......................................................................................32
RS232 connection example ......................................................................................33
   
Digital Projection HIGHlite 660 3D Series 
Rev E Februar y 2015