Digital Projection Projector HIGHlite 660 3D Series User Manual

page 13
Installation and Quick-Start Guide
POSITIONING THE SCREEN AND PROJECTOR
Adjusting the optional rigging frame
1. Remove the four adjustable feet.
2. Secure the rigging frame to the projector, as 
shown here, making sure that the rigging frame is 
in its upright position and the cable attachments 
are at the top. Three screws secure each of the 
adjuster brackets to a corner handle.
3. Adjust pitch, roll and yaw as required.
1 Vertical adjuster
2 Horizontal adjuster
3 Frame couplings
4 Fixing...

page 14
Installation and Quick-Start Guide
CHANGING THE LENS
Changing The Lens
Inserting a new lens
1. Remove the six screws 1 securing the front cover to the body of 
the projector.
2. Remove the front cover 2 from the projector.
3. Remove the lens from its packaging and remove the two protective 
caps from the front and back of the lens.
4. Insert the lens 3 into the lens aperture, making sure that the plug 
on the zoom drive mechanism lines up with the socket 4 on the 
right of the lens aperture.
5....

page 15
Installation and Quick-Start Guide
CHANGING THE LENS
Removing the lens
1. Remove the six screws 1 securing the front cover to the body of 
the projector.
2. Remove the front cover 2 from the projector.
3. Push down the lens holder tab 3.
4. Rotate the lens anti-clockwise
5. Pull the lens forward to remove it from the lens aperture.
2
1
3
Notes
 Before changing the lens, 
always make sure the projector 
is switched off and fully 
disconnected from its power 
supply.
 Always allow the lamp to cool...

page 16
Installation and Quick-Start Guide
OPERATING THE PROJECTOR
Operating The Projector
Switching the projector on
1. Connect the power cable between the mains supply and the projector. Switch on at the switch next to the power connector.
2. Wait until the self-test has completed and the standby indicator on the p\
rojector control panel shows amber. The lamp will be off and the 
projector will be in STANDBY mode.
3. Press ON on the remote control or the control panel and hold for three seconds, \
to...

page 17
Installation and Quick-Start Guide
OPERATING THE PROJECTOR
Selecting an input signal or test pattern
Input signal
1. Connect an image source to the projector.
2. Switch to the input you want to display:
• Press one of the input buttons on the remote control, or
• Open the On-screen display (OSD) by pressing MENU. Select an input signal from the Input 
Selection menu, using the UP and DOWN arrow buttons, then press OK.
Test pattern
To display a test pattern:
1. Open the OSD by pressing MENU.
2....

page 18
Installation and Quick-Start Guide
OPERATING THE PROJECTOR
Adjusting the lens
The lens can be adjusted using the Lens menu, or:
Zoom
• Press ZOOM, then use the UP and DOWN arrow buttons on the keypad or remote control to adjust the size of the\
 image on the screen. 
When the adjustment is finished, press EXIT.
Focus
• Press FOCUS, then use the UP and DOWN arrow buttons on the keypad or remote control to adjust the focus. When\
 the adjustment is 
finished, press EXIT.
Shift
• Press SHIFT, then...

page 19
Installation and Quick-Start Guide
OPERATING THE PROJECTOR
Adjusting the image
Orientation
• This can be set from the Setup menu.
Select the orientation which suits the positioning of the projector.
Keystone
• This can be set from the Geometr y menu.
Picture
• Settings such as Brightness and Contrast can be set from the Image menu.
• You can also set Brightness, Contrast or Gamma by pressing BRI, CON or GAMMA on the remote 
control.
Notes
Main MenuSetup
 Lens shift works from the audience’s...

Installation and Quick-Start Guide
   
Digital Projection HIGHlite 660 3D Series 
This page is intentionally left blank.  

CONNECTION GUIDE4 
Rev E Februar y 2015 
HIGHlite 660 3D Series
High Brightness Digital Video Projector  

Connection Guide
IN THIS GUIDE
IN THIS GUIDE
Signal Inputs And Outputs ........................................................................\
.....23
Analog inputs  ............................................................................................................23
Digital inputs and outputs ........................................................................................24
Low latency inputs...