Digital Projection Projector HIGHlite 660 3D Series User Manual

page 3
Installation and Quick-Start Guide
WHAT’S IN THE BOX?
What’s In The Box?Notes
 Make sure your box contains 
everything listed. If any pieces are 
missing, contact your dealer.
 You should save the original box 
and packing materials, in case you 
ever need to ship your projector.
 The projector is shipped without a 
lens fitted.
 Only one power cable - dependent 
on the destination territory - will be 
supplied with the projector.
VGA HDMI DVI3GSDI
CVBS1 SVIDEO
CLOSE1
23 4
COMP CVBS2
56 78
9 010+...

page 4
Installation and Quick-Start Guide
CONNECTING THE POWER SUPPLY
Connecting The Power Supply
Lift the cable lock up, push the mains connector in firmly and 
push the lock down to secure the cable.
1 AC mains inlet with cable lock
Rear view of the projector
1
Notes
 Use only the power cable 
provided.
 Ensure that the power outlet 
includes a ground connection as 
this equipment MUST be earthed.
 Handle the power cable carefully 
and avoid sharp bends. Do not 
use a damaged power cable.
   
Digital...

page 5
Installation and Quick-Start Guide
PROJECTOR OVERVIEW
Projector Over view
Front and rear views
1 Front infrared window
2 Lens
3 Air outlet
4 Adjustable feet
5 Control panel
6 Rear infrared window
7 Connection panel
8 Power switch and power connection
9 Air inlet
9
5
8
76
Rear view
Front view
4
123Notes
   
Digital Projection HIGHlite 660 3D Series 
Rev E Februar y 2015  

page 6
Installation and Quick-Start Guide
PROJECTOR OVERVIEW
Control panel indicators
1 Power indicator
 Behavior  Meaning
 Off     The projector is switched off.
  On (amber)    The projector is in Standby mode.
  On (green)    The projector is switched on (Normal mode).
2 Shutter indicator
 Behavior  Meaning
  On (amber)    The shutter is closed.
  On (green)    The shutter is open.
3 Error indicator
 Behavior  Meaning 
 On (red)     Voltage Error
  Flashing   Temperature Error
4  Lamp 1 and Lamp 2...

page 7
Installation and Quick-Start Guide
REMOTE CONTROL
Remote Control
The remote control is shipped with no battery fitted. Remove the back cover and insert the 
supplied cells while observing the correct cell polarity.
1 Transmit indicator
Flashes when the remote control sends a signal to the projector.
Lights solidly when the projector is in LENS ADJUSTMENT mode.
2 Power ON / OFF
3 A LT
Acts as a shift key. To use, press and hold this button, then press a green-labeled 
button.
4 Shutter OPEN /...

page 8
Installation and Quick-Start Guide
REMOTE CONTROL
Remote control - continued from previous page
11 Lens controls
Adjust position, zoom and focus.
12 INFO
Open the Information menu.
13 TEST
Switch to test pattern.
14 IR address
Set up an address to match the IR address of a projector.
Notes
 Only the controls shown highlighted 
are used on this projector.
 For more information about IR 
addresses, see  Setting up an IR 
address in the Operating Guide .
Remote control
VGAHDMI DVI3GSDI
CVBS1 SVIDEO...

page 9
Installation and Quick-Start Guide
REMOTE CONTROL
Infrared reception
The projector has infrared sensors at the front and back.
The angle of acceptance is 40°. Make sure that the remote control is \
within the angle of acceptance when trying to 
control the projector.
40°
40°
Infrared reception
Notes
 
Infrared reception is confirmed by 
the blue Infrared indicator flashing 
on the control panel.
 The infrared receivers are disabled 
when a remote control is connected 
via a cable. For more...

page 10
Installation and Quick-Start Guide
REMOTE CONTROL
Remote control troubleshooting
The remote control is shipped with no battery fitted. Remove the back cover and insert the 
supplied cells while observing the correct cell polarity.
If the projector fails to respond to keypress on the remote control, con\
sider the following checks.
Does the Transmit indicator flash when a button is pressed?
The blue Transmit Indicator 1 should be dark when the remote control is not being used and 
flash when a...

page 11
Installation and Quick-Start Guide
POSITIONING THE SCREEN AND PROJECTOR
Positioning The Screen And Projector
1. Install the screen, ensuring that it is in the best position for 
viewing by your audience.
2. Mount the projector, ensuring that it is at a suitable distance 
from the screen for the image to fill the screen. Set the 
adjustable feet so that the projector is level, and perpendicular 
to the screen.
The drawing below shows the positions of the feet for table 
mounting, and the fixing...

page 12
Installation and Quick-Start Guide
POSITIONING THE SCREEN AND PROJECTOR
Tilting the projector
Pitch
The projector can be positioned at any angle.
Roll and por trait mode
The projector can be tilted up to 90º with the air outlet 1 pointing upward.
In the opposite direction the projector can be tilted up to 12º.
360º
Pitch
1
12º
Roll, air outlet downward
1
1
90º
Roll, air outlet upward
1
Notes
  Always allow the projector to 
cool for five minutes before 
disconnecting the power or 
moving the...