Digital Projection Projector HIGHlite 660 3D Series User Manual

page 43
Operating Guide
USING THE PROJECTOR
Nudge
To position the image correctly on the screen, use the Nudge controls.
Lens Presets
This menu allows you to save up to five custom lens positions, which you can recall later.
To save a preset using the remote, press and hold SAVE, then press the number button for the preset 
you wish to save.
To recall a preset using the remote, press and hold LOAD, then press a number button 1 to 5.
Notes
Main Menu
Lens Nudge
 Another way of moving the lens is 
by using...

page 44
Operating Guide
USING THE PROJECTOR
Image menu
• Brightness, Contrast, Gamma, Hue and Saturation
Set the slider or select from the drop-down list as required, to improve\
 the quality of the image.
• Black Level Offset
Set this to 0 IRE or 7.5 IRE as required.
• Use V Position and H Position to adjust the position manually.
Video Filters
Set the sliders or select from the drop-down list as required, to improv\
e the quality of the image:
• Sharpness - a peaking filter to increase high...

page 45
Operating Guide
USING THE PROJECTOR
Color menu
Gamut
Peak gives you the brightest possible image.
Choose HDTV for high definition standards and SDTV for standard definition standards.
A value between 3200K and 9000K selects the relevant color temperature.
You can upload your own gamut using the Projector Controller software, an\
d then select it from 
the User 1 and User 2 settings.
Black Level and Gain sliders
Set the sliders as required.
Notes
Main MenuColor
 The Projector Controller software...

page 46
Operating Guide
USING THE PROJECTOR
Geometr y menu
Aspect Ratio
Choose from Source, Fill Display, Fill & Crop, Anamorphic and TheaterScope.
Some devices (e.g. certain DVD players) pack a 16:9 image into a 4:3 a\
spect ratio. In such cases, to 
display the image correctly, choose the Anamorphic aspect ratio.
Overscan
Set this slider to compensate for noisy or badly defined image edges.
Image with noisy edgesOverscanned image
Notes
Main Menu
Geometr y
An anamorphic lens (optional accessory) is used...

page 47
Operating Guide
USING THE PROJECTOR
Size & Position
• Set Enable to On or Off.
• Use Setting to choose:
Global, in which case these settings will be applied to all signals on all inp\
uts.
or Per Mode, in which case these settings will be applied only to the current input\
 signal.
• Set the H Position and V Position sliders as required.
• Set H Size and V Size. When Aspect Lock is set to On, the V Size slider is disabled.
• Select Reset and press OK to reset all the sliders.
Notes
Main...

page 48
Operating Guide
USING THE PROJECTOR
Geometr y Engine
Choose from Keystone, Cornerstone, Rotation, War p or Off.
• If Geometr y Engine is set to Keystone, set the H Keystone and V Keystone sliders to correct 
for any distortion caused by the projector being in a different horizontal or vertical plane to the 
screen.
1 The projector is positioned at an angle
2 The resulting image is distorted
3 The image is corrected when Keystone is applied
Notes
Main Menu
Geometr y
 Some items on this menu may...

page 49
Operating Guide
USING THE PROJECTOR
Geometr y Engine (continued)
Keystone settings
1 Projector to the left
The projector is positioned 
to the left of the screen.
To correct, apply a positive 
H Keystone value using 
the RIGHT arrow button.
2 Projector to the right
The projector is positioned 
to the right of the screen.
To correct, apply a negative 
H Keystone value using 
the LEFT arrow button.
3 Projector high
The projector is positioned 
above the screen at a 
downward angle.
To correct,...

page 50
Operating Guide
USING THE PROJECTOR
Geometr y Engine (continued)
• Pincushion / Barrel is enabled if Geometr y Engine is set to Keystone or Rotation.
Set the slider to correct for any distortion caused by the screen being \
concave or convex.
Notes
Main MenuGeometr y
 Some items on this menu may 
be unavailable depending on the 
Geometr y Engine setting.
 If possible, position the projector 
facing the screen at a right angle to 
avoid geometry corrections.
PincushionBarrel
   
Digital Projection...

page 51
Operating Guide
USING THE PROJECTOR
Geometr y Engine (continued)
• If Geometr y Engine is set to Rotation, set the Rotation slider to rotate the image on the screen.
1 DMD position
The DMD is not rotated.
2 Area outside DMD
The corners of the rotated image leave the 
DMD and appear cropped.
3 Angle of rotation
The angle equals the Rotation setting.
In this example the angle is 25°, therefore 
Rotation = 25.
Notes
Main Menu
Geometr y
 Some items on this menu may 
be unavailable depending on the...

page 52
Operating Guide
USING THE PROJECTOR
Geometr y Engine (continued)
Warp Map
Using DP Warp Generator, an external Digital Projection computer application, up to eight 
customized warp maps can be created and uploaded to the projector. If Geometr y Engine is set to 
Warp, and any warp maps have been uploaded, you can select from the drop-dow\
n list.
1 Distorted image
The image is projected on an uneven surface.
2 Warp map
The map mirrors the surface - raised areas on the surface correspond to \...