Digital Projection Projector E-vision Series User Manual

							— 42 — 
3. Right-click on Local Area Connection, and select Properties. 
 
4. In the Properties window, select the Networking tab, and select Internet Protocol (TCP/IP). 
5. Click Properties. 
 
6. Click Use the following IP address and fill in the IP address and Subnet mask, then click OK. 
  
						

							– 43 – 
7. Press the Menu button on the projector. 
8. Select Settings2→ Advanced1 → Network 
9. After getting into Network, input the following: 
 DHCP: Off 
 IP Address: 10.10.10.10 
 Subnet Mask: 255.255.255.0 
 Gateway: 0.0.0.0 
 DNS Server: 0.0.0.0 
10. Press  (Enter) / ► to confirm settings. 
Open a web browser  
(for example, Microsoft Internet Explorer with Adobe Flash Player 9.0 or higher). 
 
11. In the Address bar, input the IP address: 10.10.10.10. 
12. Press  (Enter) / ►. 
The projector is setup for remote management. The LAN/RJ45 function displays as follows. 
    
						

							— 44 — 
 
 
CATEGORY ITEM INPUT-LENGTH 
Crestron Control 
IP Address 15 
IP ID 3 
Port 5 
Projector 
Projector Name 10 
Location 10 
Assigned To 10 
Network Configuration 
DHCP (Enabled) (N/A) 
IP Address 15 
Subnet Mask 15 
Default Gateway 15 
DNS Server 15 
User Password 
Enabled (N/A) 
New Password 10 
Confirm 10 
Admin Password 
Enabled (N/A) 
New Password 10 
Confirm 10 
For more information, please visit http://www.crestron.com.  
						

							– 45 – 
Preparing Email Alerts  
1. Make sure that user can access the homepage of LAN RJ45 function by web browser (for ex-
ample, Microsoft Internet Explorer v6.01/v8.0).  
2. From the Homepage of LAN/RJ45, click Alert Settings.  
 
3. By default, these input boxes in Alert Settings are blank.  
  
						

							— 46 — 
4. For Sending alert mail, input the following: 
SMTP field is the mail server for sending out email (SMTP protocol). This is a required 
field. 
To field is the recipient’s email address (for example, the projector administrator). This 
is a required field.  
Cc field sends a carbon copy of the alert to the specified email address. This is an 
optional field (for example, the projector administrator’s assistant).  
From field is the sender’s email address (for example, the projector administrator). This 
is a required field.  
 
 
Note: Fill in all fields as specified. User can click Send Test Mail to test what setting is correct. 
For successful sending an e-mail alert, you must select alert conditions and enter a correct e-mail 
address. 
 
  
						

							– 47 – 
RS232 by Telnet Function 
Besides projector connected to RS232 interface with “Hyper-Terminal” communication by 
dedicated RS232 command control, there is alternative RS232 command control way, so called 
“RS232 by TELNET” for LAN/RJ45 interface. 
Quick Start-Guide for “RS232 by TELNET” 
Check and get the IP-Address on OSD of the projector. 
Make sure that laptop/PC can access the web-page of the projector. 
Make sure that “Windows Firewall” setting to be disabled in case of “TELNET” function filtering 
out by laptop/PC. 
 
Start => All Programs => Accessories => Command Prompt 
  
						

							— 48 — 
Input the command format like the below: 
telnet  ttt.xxx.yyy.zzz  23 (“Enter” key pressed) 
(ttt.xxx.yyy.zzz: IP-Address of the projector) 
If Telnet-Connection ready, and user can have RS232 command input, then “Enter” key 
pressed, the RS232 command will be workable. 
 
How to have TELNET enabled in Windows VISTA / 7 
By default installation for Windows VISTA, “TELNET” function is not included. But end-user 
can have it by way of “Turn Windows features On or Off” to be enabled. 
Open “Control Panel” in Windows VISTA 
 
Open “Programs”  
  
						

							– 49 – 
Select “Turn Windows features on or off” to open 
 
Have “Telnet Client” option checked, then press “OK” button. 
 
Specsheet for “RS232 by TELNET” : 
1. Telnet: TCP 
2. Telnet port: 23  
(for more detail, kindly please get contact with the service agent or team) 
3. Telnet utility: Windows “TELNET.exe” (console mode) 
4. Disconnection for RS232-by-Telnet control normally: Close Windows Telnet utility directly 
after TELNET connection ready 
5. Limitation 1 for Telnet-Control: there is less than 50 bytes for successive network payload 
for Telnet-Control application. 
Limitation 2 for Telnet-Control: there is less than 26 bytes for one complete RS232 
command for Telnet-Control. 
Limitation 3 for Telnet-Control: Minimum delay for next RS232 command must be more 
than 200 (ms). 
(*, In Windows built-in “TELNET.exe” utility, “Enter” key pressed will have “Carriage-
Return” and “New-Line” code.) 
  
						

							— 50 — 
Advanced 2 Feature 
Press the Menu button to open the OSD menu. Press ◄► to move to the Settings 2 menu. 
Press ▲▼ to move to the Advanced 2 menu and then press Enter or ►. Press ▲▼ to move up 
and down in the Advanced 2 menu. Press ◄► to enter and change values for setting. 
 
ITEM DESCRIPTION 
Sleep Timer (min) Press the cursor ◄► button to enter and set Sleep timer. The projector automatically 
turns off after the preset period of time. 
Source Filter Press  (EnterF / ► to enter the Source Filter menu. See page 51 for more 
information on Source Filter.   
						

							– 51 – 
Source Filter 
Press the ENTER button to enter the Source Filter sub menu. 
 
ITEM DESCRIPTION 
DVI Press the ◄► buttons to enter and enable or disable the DVI source. 
HDMI Press the ◄► buttons to enter and enable or disable the HDMI source. 
DisplayPort Press the ◄► buttons to enter and enable or disable the DisplayPort sourceK 
VGA1 Press the ◄► buttons to enter and enable or disable the VGA1 source. 
VGA2 Press the ◄► buttons to enter and enable or disable the VGA2 source. 
BNC Press the ◄► buttons to enter and enable or disable the BNC sourceK 
Component Video Press the ◄► buttons to enter and enable or disable the Component Video sourceK 
pJVideo Press the ◄► buttons to enter and enable or disable the SJVideo sourceK 
Composite Video Press the ◄► buttons to enter and enable or disable the Composite Video source.