Digital Projection Projector E-vision Series User Manual

							— 2 — 
Views of Projector Parts  
Front-right View 
 
ITEM LABEL DESCRIPTION SEE PAGE: 
1.  Screw For ensure the lens position 
2.  Vertical lens shift Adjusts the image position vertically 18 
3.  Lens release button Press the release button before removing the 
lens 10 
4.  Horizontal lens shift Adjusts the image position horizontally 20 
5.  IR receiver Receives IR signal from remote control 7 
6.  Lens Projection Lens 
7.  Focus ring Focuses the projected image 
18 
8.  Zoom ring Enlarges the projected image 
9.  Height adjuster Adjusts level of projector 17 
10.  Function keys See Top view—OnJscreen Display (OSD) 
buttons and LEDsK 3 
11.  Lamp cover Removes cover to replace lamp module 52 
Important: 
Ventilation openings on the projector allow for good air circulation, which keeps the projector 
lamp cool. Do not obstruct any of the ventilation openings. 
 
Note: 
Suggest to loosen the screw before lens shift adjustment and tighten up after finished 
adjustment. 
 2345678101119  
						

							– 3 – 
Top view—On-screen Display (OSD) buttons and LEDs 
 
ITEM LABEL DESCRIPTION SEE 
PAGE: 
1.  MENU Opens and exits OSD menus 
24 2.   Navigates and changes settings in the OSD 
Quick Menu – For Keystone 
3.  ENTER Enter or confirm highlighted OSD menu item 
4.  BLANK Displays a blank screen and mutes audio 
5.   Navigates and changes settings in the OSD 
Quick Menu – For Volume J 24 
6.  AUTO Optimizes image size, position, and resolution 
7.   Navigates and changes settings in the OSD 
Quick Menu – For Volume + 24 
8.    Navigates and changes settings in the OSD 
Quick Menu – For Keystone 
9.  SOURCE Enter the Source menu        
						

							— 4 — 
Rear view 
 
ITEM LABEL DESCRIPTION SEE PAGE: 
1.  VGA1 Connect a RGB cable from a computer or a video enabled device. 
2.  AUDIO IN 1 Connect the AUDIO cable from an input device. 
3.  VGA2 Connect a RGB cable from a computer or a video enabled device. 
4.  AUDIO IN 2  Connect the AUDIO cable from an input device. 
Note: Share with DVI & BNC audio input. 
5.  POWER 
Turns the projector on or off (main power switch must 
be turned on first). Press to place the projector in 
standby mode. 
13 
6.  PWR LED 
Red Standby, Over Temperature 
63 
Blue Lamp Lit , System stable 
Flashing Power on, Cooling, Error code (See as 
LED indicator table) 
7.  TEMP LED Red Over temperature 
8.  READY LED Red Lamp Lit , System stable, Lamp Fail 
Flashing Error code (See as LED indicator table) 
9.  HDMI Connect the HDMI cable from a HDMI device. 
10.  DVI-D Connect the DVI cable from a computer. 
11.  3D SYNC OUT 
(5V) Connect 3D IR glasses receiver unit. 
12.  DISPLAYPORT Connect a DISPLAYPORT cable to a DISPLAYPORT source. 
13.  USB CHARGE 
(1.5A) For USB charge. 
14.  RJ-45 Connect a LAN cable from Ethernet. 12345678910111213141516
171819
202122232425262728293031  
						

							– 5 – 
ITEM LABEL DESCRIPTION SEE PAGE: 
15.  VGA OUT Connect the RGB cable to a display. 
 (Pass through by VGA1 only) 
16.  AUDIO OUT Connect an AUDIO cable for audio loop through. 
17.  BNC Connect a BNC cable from a computer. 
18.  IR receiver Receive IR signal from remote control. 7 
19.  SERVICE For service use. 
20.  RS-232 Connects RS-232 serial port cable for remote control. 
21.  12V 
When connected to the screen through a commercially available cable, 
the screen deploys automatically on start up of the projector. The screen 
retracts when the projector is powered off (see notes below). 
22.  WIRED REMOTE Wire remote control connector (connect with wire remote connector of the 
Remote Control set). 
23.  AUDIO IN 3 L/R 
RCA (YPbPr) Connect the audio cables from a audio device. 
24.  
AUDIO IN 4 L/R 
RCA (Video/ S-
Video) 
Connect the audio cables from a audio device. 
25.  VIDEO Connect the composite cable from a video device. 
26.  S-VIDEO Connect the S-video cable from a video device. 
27.  YPbPr Connect a component video enabled device. 
28.  AC IN Connects the power cable. 
13 
29.  Power switch Turns on/off the projector. 
30.  Security chain 
lock Helps protect the projector from unauthorized use. 
61 
31.  Kensington Lock Secures to permanent object with a Kensington®  Lock 
system.        
Note: 
 To use this feature, you must plug in the connector before turn on/off the projector. 
 Screen controllers are supplied and supported by screen manufacturers. 
 Do not use this jack for anything other than intended use. 
 
Note: 
If your video equipment has both S-VIDEO and RCA jacks (composite video) connect to the  
S-VIDEO connector. S-VIDEO provides a better quality signal. 
 
Warning: 
As a safety precaution, disconnect all power to the projector and connecting devices before 
making connections. 
  
						

							— 6 — 
Bottom view 
 
ITEM LABEL DESCRIPTION SEE PAGE: 
1.  Tilt adjustor  Rotate adjuster lever to adjust angle position.  17 
2.  Ceiling support holes Contact your dealer for information on mounting the projector on a 
ceiling 
 
Note: 
When installing, ensure that you use only UL Listed ceiling mounts. 
For ceiling installations, use approved mounting hardware and M4 screws with a maximum 
screw depth of 12 mm (0.47 inch).  
The construction of the ceiling mount must be of a suitable shape and strength. The ceiling 
mount load capacity must exceed the weight of the installed equipment, and as an additional 
precaution be capable of withstanding three times the weight of the equipment (not less than 
5.15 kg) over a period of 60 seconds.   
						

							– 7 – 
Remote Control Parts 
 
 
Important: 
1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency 
fluorescent lights can disrupt remote control operation. 
 
2. Be sure nothing obstructs the path between the remote control and the projector. If the path 
between the remote control and the projector is obstructed, you can bounce the signal off 
certain reflective surfaces such as projector screens. 
 
3. The buttons and keys on the projector have the same functions as the corresponding buttons 
on the remote control. This user’s manual describes the functions based on the remote control. 
    
						

							— 8 — 
ITEM LABEL DESCRIPTION SEE PAGE: 
1.  Power OFF Turns the projector off 13 
2.  DVI Displays the DVI source selection 
3.  VGA Displays the VGA source selection 
4.  DP Displays the DisplayPort source selection 
5.  Up cursor /  
Keystone+ 
Navigates and changes settings in the OSD 
Quick Menu – For Keystone 
24 6.  ENTER Enters and confirms settings in the OSD 
7.  Right cursor Navigates and changes settings in the OSD 
8.  Down cursor /  
Keystone- 
Navigates and changes settings in the OSD 
Quick Menu – For Keystone 
9.  3D Activate 3D video (not available in D5180HD series) 
10.  PICTURE MODE Changes the Display Mode setting 
11.  SOURCE Alternate input source 24 
12.  CONTRAST Displays the contrast settings bar 
13.  BRIGHT Displays the brightness setting bar 
14.  SHARP Displays the sharpness setting bar  
15.  COLOR Displays the color setting bar 
16.  FREEZE Freezes/unfreezes the on-screen picture 
17.  VOL + Adjusts volume 
24 18.  AUTO Auto adjustment for frequency, phase, and position 
19.  VOL - Adjusts volume 
20.  BLANK Makes the screen blank 
21.  TINT Displays the tint setting bar 
22.  MUTE Mutes the built-in speaker 
23.  STATUS Opens the OSD Status menu (the menu only opens when an input 
device is detected) 
24.  ASPECT RATIO Displays the ASPECT RATIO selections 
25.  MENU Opens or closed the OSD 24 
26.  Left cursor Navigates and changes settings in the OSD 24 
27.  COMP Displays the Component source selection 
28.  VIDEO Displays the VIDEO source selection 
29.  HDMI 1 Displays the HDMI 1 source selection 
30.  Power ON Turns the projector on 13 
31.  Status LED Lights when the remote control is used 
32.  IR transmitter Transmits signals to projector 
33.  Wired remote 
connector Wired remote function used  
						

							– 9 – 
Remote Control Operating Range 
The remote control uses infrared transmission to control the projector. It is not necessary to point 
the remote directly at the projector. Provided you are not holding the remote perpendicular to the 
sides or the rear of the projector, the remote will function well within a radius of about 7 meters (23 
feet) and 15 degrees above or below the projector level. If the projector does not respond to the 
remote control, move a little closer.   
Projector and Remote Control Buttons 
The projector can be operated using the remote control or the buttons on the top of the projector. 
All operations can be carried out with the remote control; however, the buttons on the projector 
are limited in use.   
						

							— 10 — 
SETUP AND OPERATION 
Inserting the Remote Control Batteries  
1.  Remove the battery compartment 
cover by sliding the cover in the 
direction of the arrow. 
 
2.  Insert the battery with the positive 
side facing up. 
 
3.  Replace the cover. 
 
 
Caution: 
1. Only use AA batteries (Alkaline batteries are recommended). 
 
2. Dispose of used batteries according to local ordinance regulations.  
 
3. Remove the batteries when not using the projector for prolonged periods. 
Installing or Removing the Optional Lens 
Caution:     
						

							– 11 – 
 Do not shake or place excessive pressure on the projector or the lens components as the 
projector and lens components contain precision parts. 
 Before removing or installing the lens, be sure to turn off the projector, wait until the cooling 
fans stop, and turn off the main power switch. 
 Do not touch the lens surface when removing or installing the lens. 
 Keep fingerprints, dust or oil off the lens surface. 
 Do not scratch the lens surface. 
 Work on a level surface with a soft cloth under it to avoid scratching. 
 If you remove and store the lens, attach the lens cap to the projector to keep off dust and dirt. 
Removing the Existing Lens From the Projector 
1.  Pull and release the top cover to 
open as shown. 
 
2.  Push the LENSE RELEASE button 
to the unlock position. 
3.  Grasp the lens. 
 
4.  Rotate the lens counterclockwise. 
The existing lens will be 
disengaged. 
5.  Pull out the existing lens slowly.