Digital Projection Projector E-Vision 6500 Series User Manual

Digital Projection E-Vision 6500 Series  A Tour Of The Menus Operating Guide
Page 35
Signal menu
Horizontal and Vertical Position, Phase, Clock
• Adjust the sliders for these settings, as required.
Reset
• Press ENTER to restore the four settings above their factory defaults.
• When the warning message appears, use  or to move the green highlight to 
YES or NO, then press ENTER to confirm your selection.
Resolution
• Set this to Auto, unless the projector has problems selecting between Wide and 4:3 with...

Digital Projection E-Vision 6500 Series  A Tour Of The Menus Operating Guide
Page 36
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
 Overscan is used to compensate for 
noisy	or	badly	defined	image	edges,	
by increasing the size of the image, 
to force the edges off-screen.
  It is always On for the Video and 
S-Video inputs, and for 480i and 
576i signals.
 The Video System setting is 
available only for signals on the 
Video and S-Video inputs.
 The Video...

Digital Projection E-Vision 6500 Series  A Tour Of The Menus Operating Guide
Page 37
Setup menu
Auto Search
• When this is set to On, the projector will search for an alternative input source when the 
current input source is disconnected
• When this is set to Off, the projector will show the ‘background’ screen when the current 
input source is disconnected.
Auto Power Off
• Set this to On, if you want the projector to go into Standby mode when no input source 
is detected for 20 minutes.
Auto Power On...

Digital Projection E-Vision 6500 Series  A Tour Of The Menus Operating Guide
Page 38
Background
• Set this to determine what appears on screen when the projector is searc\
hing for a valid 
input source.
3D Mode
• Use the 3D Mode Submenu to turn the DLPLink synchronisation signal On and Off, and 
to invert the signal if necessary.
Aspect Ratio
• Select from Normal, Full, 4:3, 16:9, and Native, as follows:
• Normal: the image will be displayed at its intended aspect ratio, filling either the full 
height...

Digital Projection E-Vision 6500 Series  A Tour Of The Menus Operating Guide
Page 39
Advance Setting submenu
Security Lock
• When the Security Lock is enabled, a security Password will need to entered before the 
projector can be used, or before the lock can be Disabled.
• When setting the lock for the first time, the Password will need to be entered twice, to 
ensure that it has been entered correctly.
Keypad Lock
• To  lock the control panel keys, use  or to move the green highlight to YES or 
NO, then...

Digital Projection E-Vision 6500 Series  A Tour Of The Menus Operating Guide
Page 40
Messaging
• Set Messaging to Off  if you do not want projector status messages to be displayed.
Setup menu Advance Setting submenu continuedNotes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
Setup MenuAdvance Setting Submenu
MENU =END|SEL /ADJ .|SEL.
Setup
Video Installation
Signal
Picture
Security Lock
Keypad Lock
Image Capture
Wall Color
Messaging
Advance Setting
Off
On
Disable...

Digital Projection E-Vision 6500 Series  A Tour Of The Menus Operating Guide
Page 41
Installation menu
Language
• Select a language as required.
Lamp Control
• Set this to Both, Lamp1, Lamp 2 or Auto 1 as required.
Lamp Mode
• Set this to Normal or Eco as required.
Projection Mode
• Set this to Front, Rear, Ceiling+Front or Ceiling+Rear as required.
Fan Mode
• Set this to Normal, High or Up & Down as required. Select High to compensate for reduced air density at higher altitudes. Select 
Up & Down if the...

Digital Projection E-Vision 6500 Series  A Tour Of The Menus Operating Guide
Page 42
Advance Setting
Keystone
•  Set the slider to correct for any vertical keystone distortion.
Image Resizing
•  Set this to correct for any image distortion when keystone correction i\
s being used.
Filter Message
• Select a Filter Message time inter val from the list, or select Off.
LAN/RS232C
• Select from LAN or RS232C as the remote connection used for external control of the projector .
Communication Speed
• Sets the...

Digital Projection E-Vision 6500 Series  A Tour Of The Menus Operating Guide
Page 43
Installation menu, Advance Setting submenu continued
Network
Link
• For information only: reports whether the projector detects a physical L\
AN connection. 
The LAN settings below should be made manually.
DHCP Client
• Set DHCP Client to On if the IP Address is to be assigned by a DHCP server, or Off if it 
is to be set here.
IP Address, Subnet Mask, Gateway and DNS
• If DHCP is set to Off:
• Edit the settings as...

Digital Projection E-Vision 6500 Series  A Tour Of The Menus Operating Guide
Page 44
• When the warning message appears, use  or to move the green highlight to 
YES or NO, then press ENTER to confirm your selection.
Reset
All Reset
• Projector will ask for confirmation before restoring all settings to factory defaults.
• When the warning message appears, use  or to select YES or NO, then press 
ENTER/SELECT to confirm your selection.
Filter Timer Reset
• Projector will ask for confirmation before...