Digital Projection Projector E-Vision 6500 Series User Manual

							Digital Projection E-Vision 6500 Series  A Tour Of The Menus Operating Guide
Page 35
Signal menu
Horizontal and Vertical Position, Phase, Clock
• Adjust the sliders for these settings, as required.
Reset
• Press ENTER to restore the four settings above their factory defaults.
• When the warning message appears, use  or to move the green highlight to 
YES or NO, then press ENTER to confirm your selection.
Resolution
• Set this to Auto, unless the projector has problems selecting between Wide and 4:3 with 
some signals on the Computer 1, Computer 2 and Component inputs.
Auto Sync
• Set this to On if you want the projector to automatically synchronise with the input s\
ignal.
• Set this to Off if the settings are to be made manually, using the sliders above only.
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
 These settings are used for VGA 
signals only.
 Do NOT do this unless you are 
sure that you want to restore the 
settings to their factory defaults.
 The Resolution setting is needed 
only for VESA  1024x768_ 60, 
VESA 1280x768_60, 
VESA 1400x1050_60 and 
VESA 1680x1050_60 signals on 
the Computer 1, Computer 2 and 
Component inputs.
 The Auto Sync setting is used for 
VGA signals only. 
Rev D July 2014  
						

							Digital Projection E-Vision 6500 Series  A Tour Of The Menus Operating Guide
Page 36
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
 Overscan is used to compensate for 
noisy	or	badly	defined	image	edges,	
by increasing the size of the image, 
to force the edges off-screen.
  It is always On for the Video and 
S-Video inputs, and for 480i and 
576i signals.
 The Video System setting is 
available only for signals on the 
Video and S-Video inputs.
 The Video Setup setting is 
available only for 480i signals on 
the Computer 1, Computer 2 and 
Component inputs, and NTSC3.58 
signals on the Video and S-Video 
inputs.
 Closed Captions are recognised 
only with NTSC3.58 signals on the 
Video and S-Video inputs.
Video menu
Overscan
• Set this to On or Off as required.
Video System
• Set this to Auto, unless the projector has problems selecting between PA L, SECAM, 
NTSC4.43, NTSC3.58, PAL-M, PAL-N  and PAL-60.
Video Setup
• Set this to 0IRE or 7.5IRE as required.
Closed Caption
• Set this to Off or CC1 as required. 
Rev D July 2014  
						

							Digital Projection E-Vision 6500 Series  A Tour Of The Menus Operating Guide
Page 37
Setup menu
Auto Search
• When this is set to On, the projector will search for an alternative input source when the 
current input source is disconnected
• When this is set to Off, the projector will show the ‘background’ screen when the current 
input source is disconnected.
Auto Power Off
• Set this to On, if you want the projector to go into Standby mode when no input source 
is detected for 20 minutes.
Auto Power On
• Set this to On, if you want the projector to start up immediately when the mains is 
connected.
• Set this to Off, if you want the projector to go into Standby mode when the mains is 
connected. In this case, the projector will not start up until the POWER button is pressed 
on the control panel or the remote control.
Standby Mode
• Set this to Standard or Eco as required.
MENU=END|SEL /ADJ .|SEL.
Setup
Video Installation
Signal
Picture
Standard On
Auto Search
Auto Power Off
Auto Power On
Standby Mode
Background
Advance Setting
Aspect
Ratio
3D
Mode On
On
Logo
Normal
Notes
  See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
 To set the background screen, see 
the next page.
 When Standby Mode is set to Eco:
 the Monitor Out signal is disabled,
  and the RS232 connection is 
disabled, so it will not be possible 
to turn the projector On remotely, 
except via the LAN connection. 
Rev D July 2014  
						

							Digital Projection E-Vision 6500 Series  A Tour Of The Menus Operating Guide
Page 38
Background
• Set this to determine what appears on screen when the projector is searc\
hing for a valid 
input source.
3D Mode
• Use the 3D Mode Submenu to turn the DLPLink synchronisation signal On and Off, and 
to invert the signal if necessary.
Aspect Ratio
• Select from Normal, Full, 4:3, 16:9, and Native, as follows:
• Normal: the image will be displayed at its intended aspect ratio, filling either the full 
height or width of the screen as appropriate.
• Full: the image will fill the height and width of the screen, depending on the 
resolution of the projector.
• 4:3: the image will be displayed with a 4:3 aspect ratio, fitting the full height and/or 
width of the screen, depending on the resolution of the projector.
• 16:9: the image will be displayed with a 16:9 aspect ratio, fitting the full height and/or 
width of the screen, depending on the resolution of the projector.
• Native: the image will be displayed pixel for pixel with no scaling. This could be 
smaller than full screen or cropped to full screen, depending on the res\
olutions of the 
image and projector.
Notes
 To set a background image to 
be displayed when Custom is 
chosen, see the Advanced Setting 
Submenu on the next page.  
 The full height and width of the 
screen will depend on the projector 
model. For more information, see 
the Specification leaflet, or the 
Important Information.
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
Setup menu continued 
Rev D July 2014  
						

							Digital Projection E-Vision 6500 Series  A Tour Of The Menus Operating Guide
Page 39
Advance Setting submenu
Security Lock
• When the Security Lock is enabled, a security Password will need to entered before the 
projector can be used, or before the lock can be Disabled.
• When setting the lock for the first time, the Password will need to be entered twice, to 
ensure that it has been entered correctly.
Keypad Lock
• To  lock the control panel keys, use  or to move the green highlight to YES or 
NO, then press ENTER to confirm your selection.
• To  unlock the keys, press  and hold for 5 seconds.
Image Capture
• To capture the current screen image for use as the Custom background, use Save Image. This will take approximately 2 minutes.
• To delete the currently saved image, use Delete.
Wall Color
• Set this to suit the projection screen.
Digital Zoom
• Enlarge a section of the image.
Notes
 See also Using the Menus, earlier 
in this guide and  Menu Map, later in 
this guide.
Setup Menu Advance Setting Submenu
 The Password is made of a 
combination	of	five	presses	on	the		
, ,and keys.
  Image Capture is available only:
  - for Component, Computer 1, 
Computer 2 and Computer 3 inputs;
  - when Aspect Ratio is set to 
Normal;
  - for native resolution images: 
(1280x800 for E-Vision WXGA, 
1024x768 for E-Vision XGA)
 There are two storage locations: one 
for the 4 segment color wheel and 
one for 6 segment color wheel.
  If you change wheels you will need 
to recapture the image. If you 
change	back,	the	image	for	the	first	
wheel will still be in memory.
MENU =END|SEL /ADJ .|SEL.
Setup
Video Installation
Signal
Picture
Security Lock
Keypad Lock
Image Capture
Wall Color
Digital Zoom
Advance Setting
Off
0
Disable
Messaging On
Setup menu continued 
Rev D July 2014  
						

							Digital Projection E-Vision 6500 Series  A Tour Of The Menus Operating Guide
Page 40
Messaging
• Set Messaging to Off  if you do not want projector status messages to be displayed.
Setup menu Advance Setting submenu continuedNotes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
Setup MenuAdvance Setting Submenu
MENU =END|SEL /ADJ .|SEL.
Setup
Video Installation
Signal
Picture
Security Lock
Keypad Lock
Image Capture
Wall Color
Messaging
Advance Setting
Off
On
Disable 
Rev D July 2014  
						

							Digital Projection E-Vision 6500 Series  A Tour Of The Menus Operating Guide
Page 41
Installation menu
Language
• Select a language as required.
Lamp Control
• Set this to Both, Lamp1, Lamp 2 or Auto 1 as required.
Lamp Mode
• Set this to Normal or Eco as required.
Projection Mode
• Set this to Front, Rear, Ceiling+Front or Ceiling+Rear as required.
Fan Mode
• Set this to Normal, High or Up & Down as required. Select High to compensate for reduced air density at higher altitudes. Select 
Up & Down if the projector is positioned at an upward or downward angle.
Test Pattern
• Select a Test Pattern from the list.
Notes
 See also Using the Menus, earlier 
in this guide and  Menu Map, later in 
this guide.
  When Lamp Control is set to 
Auto 1, the projector will turn on 
using the lamp with the least hours 
of use. 
Rev D July 2014  
						

							Digital Projection E-Vision 6500 Series  A Tour Of The Menus Operating Guide
Page 42
Advance Setting
Keystone
•  Set the slider to correct for any vertical keystone distortion.
Image Resizing
•  Set this to correct for any image distortion when keystone correction i\
s being used.
Filter Message
• Select a Filter Message time inter val from the list, or select Off.
LAN/RS232C
• Select from LAN or RS232C as the remote connection used for external control of the projector .
Communication Speed
• Sets the Serial Port (RS232) baud rate. Longer cable connections may require lower speeds.
Notes
 See also Using the Menus, earlier 
in this guide and  Menu Map, later in 
this guide.
Installation Menu Advance Setting submenu
 Only one remote connection can be 
used at any one time.
MENU =END|SEL /ADJ .|SEL.
Setup
VideoInstallation
Signal
Picture
Keystone
Image Resizing
Filter Message
LAN/RS232 C
Network
Advance Setting
LAN
0
0
10000H
Communication Speed
9,600
Installation menu continued 
Rev D July 2014  
						

							Digital Projection E-Vision 6500 Series  A Tour Of The Menus Operating Guide
Page 43
Installation menu, Advance Setting submenu continued
Network
Link
• For information only: reports whether the projector detects a physical L\
AN connection. 
The LAN settings below should be made manually.
DHCP Client
• Set DHCP Client to On if the IP Address is to be assigned by a DHCP server, or Off if it 
is to be set here.
IP Address, Subnet Mask, Gateway and DNS
• If DHCP is set to Off:
• Edit the settings as required.
Apply
• Press ENTER to apply the address settings.
Notes
 See also Using the Menus, earlier 
in this guide and  Menu Map, later in 
this guide.
Installation Menu Advance Setting  Network submenu
 If DHCP is set to On, it will not be 
possible to edit the address settings. 
Rev D July 2014  
						

							Digital Projection E-Vision 6500 Series  A Tour Of The Menus Operating Guide
Page 44
• When the warning message appears, use  or to move the green highlight to 
YES or NO, then press ENTER to confirm your selection.
Reset
All Reset
• Projector will ask for confirmation before restoring all settings to factory defaults.
• When the warning message appears, use  or to select YES or NO, then press 
ENTER/SELECT to confirm your selection.
Filter Timer Reset
• Projector will ask for confirmation before resetting the timer to zero.
• When the warning message appears, use  or to select YES or NO, then press 
ENTER/SELECT to confirm your selection.
Information
• The final submenu gives information about the projector, eg:
Notes
 Do NOT do this unless you are 
sure that you want to restore ALL 
settings to their factory defaults.
 Do NOT do this unless you are 
sure that you want to reset the 
Filter Timer to zero.
Installation Menu
Information submenu
MENU =END
Setup
VideoInstallation
Signal
Picture
Input
Signal Info
Lamp 1Timer
Lamp 2Timer
Filter Timer
Information
[0000] h COMPUTER1
Model Name E-Vision6500WXGA
1024
x768 @60Hz
[0000] h[00] min (100 %)
[0000] h[00] min (100 %)
S/N C202XXXX00764
Software Version E-Vision 6500WXGA -PO 2/4 S
Installation menu continued 
Rev D July 2014