Digital Projection Projector E-Vision 6500 Series User Manual

							Digital Projection E-Vision 6500 Series  IN THIS GUIDE Remote Communications Guide
55
ASCIIHEXFunctionDescriptionReturn String
V99G030256 39 39 47 30 33 30 32 0DGet AV MutePn/F
V99S0302n56 39 39 53 30 33 30 32 n 0DSet AV  MuteP/F
V99G030456 39 39 47 30 33 30 34 0DGet Image FreezePn/F
V99S0304n56 39 39 53 30 33 30 34 n 0DSet Image FreezeP/F
V99G030856 39 39 47 30 33 30 38 0DGet Projection 
Mode
0: Front 
1: Rear 
2: Ceiling + Front 
3: Ceiling + Rear
Pn/F
V99S0308n56 39 39 53 30 33 30 38 n 0DSet Projection 
Mode
0: Front 
1: Rear 
2: Ceiling + Front 
3: Ceiling + Rear
P/F
V99G030956 39 39 47 30 33 30 39 0DGet Vertical 
Keystone
n= -80~80Pn/F
V99S0309n56 39 39 53 30 33 30 39 n 0DSet Vertical 
Keystone
n= -80~80P/F
Command Group 04 (Remote Control buttons)
ASCIIHEXFunctionDescriptionReturn String
V99S040156 39 39 53 30 34 30 31 0DONP/F
V99S040256 39 39 53 30 34 30 32 0DOFFP/F
V99S040356 39 39 53 30 34 30 33 0DFocus+P/F
V99S040456 39 39 53 30 34 30 34 0DFocus-P/F
V99S040556 39 39 53 30 34 30 35 0DZoom +P/F
V99S040656 39 39 53 30 34 30 36 0DZoom -P/F
V99S040856 39 39 53 30 34 30 38 0DLENS SHIFTP/F
V99S040956 39 39 53 30 34 30 39 0DUPP/F
V99S041056 39 39 53 30 34 31 30 0DDOWNP/F
V99S041156 39 39 53 30 34 31 31 0DLEFTP/F
V99S041256 39 39 53 30 34 31 32 0DRIGHTP/F
V99S041356 39 39 53 30 34 31 33 0DENTERP/F
Continued
Notes
 Note: spaces are shown in the 
examples for clarity, but are NOT 
used in the actual commands or 
replies.
	 In	the	 Ascii	column,	the	final	[CR]	
has been omitted for clarity.
 In the Command Strings and the 
Return Results,  ‘n’ represents a 
data string.
 In the Return Result Strings:
  ‘P’ is returned for a successful Set 
command;
 ‘Pn’ is returned for a successful Get 
command;
 ‘F’ is returned for a failed command.
 When Standby Mode is set to Eco:
  the RS232 connection is  disabled, 
so it will not be possible to turn the 
projector On remotely, except via the 
LAN connection. 
Rev D July 2014  
						

							Digital Projection E-Vision 6500 Series  IN THIS GUIDE Remote Communications Guide
56
ASCIIHEXFunctionDescriptionReturn String
V99S041456 39 39 53 30 34 31 34 0DMENUP/F
V99S041556 39 39 53 30 34 31 35 0DRETURNP/F
V99S041656 39 39 53 30 34 31 36 0DINPUTP/F
V99S041756 39 39 53 30 34 31 37 0DPICTUREP/F
V99S041856 39 39 53 30 34 31 38 0DAVMUTEP/F
V99S041956 39 39 53 30 34 31 39 0DAUTO SYNCP/F
V99S042056 39 39 53 30 34 32 30 0DASPECTP/F
V99S042356 39 39 53 30 34 32 33 0DOVERSCANP/F
V99S042456 39 39 53 30 34 32 34 0DFREEZEP/F
V99S042556 39 39 53 30 34 32 35 0D3D MODEP/F
V99S042656 39 39 53 30 34 32 36 0DINFO.P/F
Notes
 Note: spaces are shown in the 
examples for clarity, but are NOT 
used in the actual commands or 
replies.
	 In	the	 Ascii	column,	the	final	[CR]	
has been omitted for clarity.
 In the Command Strings and the 
Return Results,  ‘n’ represents a 
data string.
 In the Return Result Strings:
  ‘P’ is returned for a successful Set 
command;
 ‘Pn’ is returned for a successful Get 
command;
 ‘F’ is returned for a failed command. 
Rev D July 2014  
						

							Digital Projection E-Vision 6500 Series  PJLink Remote Communications Guide
57
Notes
 The TCP Port number is 5450.
	 The	PJLink	specification	can	be	
downloaded from 
http://pjlink.jbmia.or.jp/english - 
click on the Specifications link.
PJLink
The LAN IP Address of the projector can be set by using the Network submenu, which can 
be found in the Advanced Setting submenu in the Installation menu.
Once the LAN IP Address has been set, it is possible to assign a Host Name and Domain 
Name to the projector, and to set up an Alert Mail address and PJLink password:
• Point your browser at the projector by typing the url 
http:///lanconf.html into the address bar, 
then press the Enter key.
• The embedded webpage shown here should appear.
Settings
Host Name
Up to 60 alpha-numeric characters can be entered. Press the Apply 
button to confirm the new name.
Domain Name
Up to 60 alpha-numeric characters. Press the Apply button to confirm 
the new name.
Mail
When enabled, an email will be sent to up to three specified 
addresses, when the lamp reaches the end of its useable life, or if an 
error occurs on the projector. Press the Apply button to confirm the 
new settings.
A test mail can be sent to check that the settings have been made 
correctly. Press the Execute button to send the test message.
PJLink
When enabled, a password can be set. Press the Apply button to 
confirm the new password.
The projector supports all the commands of PJLink Class 1. 
Rev D July 2014  
						

							Digital Projection E-Vision 6500 Series  LAN Control Utility Remote Communications Guide
58
LAN Control Utility
The LAN IP Address of the projector can be set by using the Network submenu, which can 
be found in the Advanced Setting submenu in the Installation menu.
Once the LAN IP Address has been set, it is possible to control some basic functions by \
using the emedding LAN Control Utility:
• Point your browser at the projector by typing the url 
http:///index.html into the address bar, then press the Enter key.
• The embedded webpage shown here should appear.
Power ON/STANDBY
Click on the buttons to turn the projector On or into Standby mode.
Picture controls
Click on the and controls to adjust the settings as required.
Input Select
Click on the Input buttons to switch to the required input.
AV Mute
Click to switch video On or Off.
Status
The panel shows the status of the lamps and filters. Click on the 
Refresh button to update the readings.
Notes
 For full details of how to use the 
menu system, see the Operating 
Guide.
 The lamp life percentage shown 
here is based on expected lamp life 
in controlled laboratory conditions.
  Actual life may vary depending on 
installation environment, orientation 
and lamp mode (Normal or Eco).” 
Rev D July 2014