Digital Projection LIGHTNING 10sx And LIGHTNING 15sx User Manual

Chan:This is the channel number entered on the remote control keypad to select an
input. The channels are listed in numerical order and are scrollable.
Name: A name of up to 14 characters in length can be entered to describe each
channel.
IP:Specifies which input connection on the rear of the projector (1, 2 or 3) will be
used for a particular channel.
ADR:The switcher input address. If a number is preset here, the projector will
command a video switcher to select that input via the RS232 serial control...

SELECT Command
Channel selection can be made in two ways, by simply keying in the channel
number on the remote control or by selection in the Channel Set-up screen. Using
the remote control is quicker if you know the channel number required, but if you
dont, the Channel Set-up screen will remind you. 
To select a channel using the On Screen Display, first choose Channel Set-up
from the the Main Menu and locate the cursor over the desired channel using the
ñand òbuttons. Highlight SELECT from the options...

VIEW Command
The VIEW command will display information about a channel. When viewing a
channel the information displayed cannot be modified.
Highlighting a channel in the Channel Set-up menu and selecting VIEW will
display the View Channel window (see example below). Further information can be
accessed by selecting INFO, SIZE POS and COMPMODE. To exit the window and
return to the Channel Set-up menu press the Close soft button or EXIT on the
remote.
CÑ16
System Operation
OPERATION
LBV00056; Revision A -...

COPY Command
The COPY command allows all or just selected parameters from a channel to be
copied to another channel. To copy a channel, highlight it with the cursor in the
Channel Set-up menu and select the COPY command. This displays the Copy
Channel screen containing three main fields: Copy From, Copy To and Copy
Parameters.
Copy From- displays the name and number of the channel to be copied.
Copy To- displays the name and number of the destination channel.
Copy Parameters- allows copying of all or...

The next stage is to select which parameters you wish to copy by crossing either the
All or Selected check boxes. If Selected is chosen, the check boxes of the
parameters you wish to copy must be crossed. The choices available are Input
Configuration, Size & Position, Colour Temperature, Switcher Source, Brightness,
Contrast, Saturation, Sharpness and Hue. With the desired parameters selected
pressing OK soft button will copy them to the destination channel and return you to
the Channel Set-up screen.
If...

NEW Command
The NEW command allows you to set up a channel for a new input device. When
you are in the Channel Set-up menu, highlight an empty channel and select NEW.
Assuming you have enough memory left in the projector, you will enter the NEW
function. The default parameters as specified in the User Preferences menu will be
automatically entered in the data fields. These parameters can be modified as
required. If you need to define specific size, position or computer mode parameters,
this can be done...

Configuration- Select either Video or Computer according to the input device. The
selections for a video configuration are PAL, NTSC, SECAM, CPENT and 
S-VIDEO. An AUTO configuration will be applied if no selection is made.
If a CPENT video input is selected you must state the component format (RGB or 
Y Pr Pb). Ext. Mixed Syncs should selected when using base band video signals
with a combined sync e.g. RGBS signals.
A computer configuration requires the selection of a computer card from the library....

MODIFY Command
The MODIFY option in the Channel Set-up screen allows you to change certain
parameters for individual channels. The definable parameters in the Modify
Channel window are the same as for a new channel. At the base of the Modify
Channel window there are three options (Info, Size Pos and Compmode) that are
not available in the New Channel function.
INFO (Channel Information)
Selecting the INFO command will open the Channel Info window which displays
further details about the channel under...

SIZE POS (Channel Size and Position)
The SIZE POS function is entered by pressing a soft button located at the base of
the Modify dialogue box and consists of two screens.
The first screen allows you to select a computer mode from a list or to select video.
The horizontal and vertical scan rates of the computer configuration will be
displayed, but for a video configuration it will simply state- Video Configuration.
To exit this screen you must use the Exit button on the remote.
The screen rate...

Horizontal Position:Measured as a percentage, 0 is far left and 100 is far right.
Vertical Position:0% is the bottom and 100% is the top.
Horizontal & Vertical Size:Size is also measured as a percentage with 0 being the
smallest image and 100 the largest.
Pixel Phase & Resolution:
The pixel phase is the point in the line timing where the
pixel sample is taken and is represented as a number between 0 and 100. The
Resolution can be set from 630 to 1280 and defines the number of pixels in a scan line....