Digital Projection LIGHTNING 10sx And LIGHTNING 15sx User Manual

The Set Projector Address is accessed through the Main menu and it allows you to
set a unique address for the projector. This will enable it to respond to commands
received from an external computer or from the remote control when using multiple
projectors.
Enter Address-Enter the address of the projector as a numeric value between 1
and 31 using the remote control. In addition to this value the projector will always
respond to an address of zero. The number will be preceded by 0 (zero), but you are
not...

CANCEL
OK User Memory Available 100% Computer NameADD COMPUTER
NEW
/MODIFY CREATE
COPY DELETE
The Add Computerfunction allows groups of computer modes to be created and
saved to the projector under a collective name. Other options available through this
function include the modification of existing mode parameters, the deletion of a
computer card or mode and the copying and renaming of a complete computer card.
After selection from the Main Menu the Add Computerscreen will be displayed.
This screen can...

CREATE/MODIFY Command
The CREATE/MODIFY command is used to create (add) a new computer mode to
the projectors library or modify an existing computer mode.
CREATING A NEW COMPUTER
In order to add a new computer to the projectors library select CREATE/MODIFY
from the Add Computerscreen. The Computer Name window will open asking
you to enter the name of the new computer.
Assuming you have sufficient memory, entering a new computer name will return
you to the Add Computer screen where the New Computer Name...

DELETE MODIFY NEW COPY VIEW SELECT
K
---
ODE 500
CANCELOK
SAVE AS
Computer Video7Mode Name
    Scan    Sync Polarity
 Hor31.50kHz Pos Neg N/A
 Ver60.00Hz  Pos Neg N/A
               Res  Phase
 Active Pixels  800 100
 Aspect Ratio   4x3800x600 Mode Parameters--- er
The duplication of a computer name allows you to save a different set of mode
parameters for the same computer. If a card using the factory defaults is selected, a
duplicate will be made using the same name but with an asterix ( 
*) at the...

After entering the required information select OK, a confirmation box will appear
stating Computer graphics card will be created/updated. Press OK to proceed or
CANCEL to ignore. Select OK to save the new mode.
MODIFYING AN EXISTING COMPUTER CARD MODE
Having selected an existing computer card it is possible to modify a specific mode
for that card. After selecting the mode to be modified from the resolution mode
fly-out list you will enter the MODE PARAMETERS window. The computer and
mode names will be...

OK CANCEL COPY DELETECREATE
/MODIFY
     DELETE COMPUTER
Computer Card DIAMOND
 Delete All Modes
 Delete Single Mode
Select Mode 1024x768
    Scan   Sync Polarity
Hor62.56kHz Pos  Neg  N/A
Ver65.00Hz  Pos  Neg  N/A
           CANCEL    OK
The DELETE COMPUTER screen (below) displays the card name for verification
and gives you the choice of deleting all modes or a single mode by checking the
appropriate box.
Delete All Modes:When you Check this box the Select Mode option along with
the mode information...

COPY Command
The Copy function in the Add Computer screen permits the user to make a copy of
an existing computer card with all its associated modes and give it a different name.
It is not possible to copy an individual mode, either within a computer card or
between cards.
To copy a computer card it is necessary to select it from the computer name fly-out
list and press COPY. Assuming you have sufficient memory available you will
enter the COPY COMPUTER window (See below). If you dont have enough
memory...

-
If a New computer signal is applied when the selected channel is configured for
computer and the computer signal does not identify a mode which matches, the
screen will display an image using default Size, Position, Number of Pixels, Pixel
Phase and Aspect Ratio. These default parameters will be supplied from ROM. A
message will also appear stating- New Mode will be lost if not saved or if Channel
is changed.
The display will then have to be adjusted manually to give an optimum image.
These default...

Configuring a Video Channel
1. Set Gamma in Image Mode to Preferred Value
2. In the Channel Set-up Menu select the correct input, aspect ratio, colour 
temperature and format (i.e. PAL, NTSC, SECAM, S-Video, Component RGB 
or Component Y Pr Pb).
3. Using either the Size & Position sub menu or the single press remote control 
buttons, adjust the size and position until the image fills the screen exactly.
4. Apply a Pluge Test Pattern (or a test signal or tape which has near blacks and 
near saturated...

-
-
-
Configuring a Computer Channel
1. Set Gamma in Image Mode to Preferred Value
2. In the Channel Set-up Menu select Computer Source and Colour Temperature.
3. Apply intended computer input.
4. Select Size & Position.
5. The cursor should be over the correct rate mode, press ENTER.
6. Set Pixels to equal the number of pixels per line in the signal source.
7. Define the aspect ratio as 4 x 3.
8. Adjust the Horizontal and Vertical Size until beating patterns minimise or 
disappear (use an alternate...