Digital Projection LIGHTNING 10sx And LIGHTNING 15sx User Manual

Components
Integrated Keypad ....................................................AÑ16
Remote Control ..........................................................AÑ16
Palm Pilot Control Utility............................................AÑ16
Overview
OVERVIEW
LBV00056; Revision A - 23/08/99 

Projector Packaging
To provide protection during transportation, the projector is surrounded with foam,
placed on a wooden palette and enclosed within a sturdy fibreboard carton. The
package is then secured with banding and fastening clips.
To unpack the projector, first release the two fastening clips and remove the 
banding. Next, using the finger holes provided, gently lift off the outer cover of the
carton. Do not open the tape seal on the top of the cover.
Lift out the carton containing the...

Compliance with Regulatory Bodies 
The LIGHTNING10sxand LIGHTNING15sxhave been designed to comply with
IEC950 and UL 1950 (formal UL approval in process), the International safety 
standards for information technology and electrical business equipment. These 
standards impose stringent safety requirements on the construction and operation to
prevent energy hazards, access to live parts and the risk of electric shock. The safety 
standards also provide regulations on internal and external temperature...

Safety Warnings
All the safety warning in this manual are in bold italic type and can be identified by
the symbol shown on the left.
A list containing all the warnings is given below. It is recommended that time is
taken to study these before installing or operating the projector.
The projector should always be lifted using the handrail. Do not attempt to lift the
projector by holding the covers or the lens.
The customer should never attempt to disassemble the lamp from its housing or to
dispose of it...

At least 4 people are required for safe movement of the projector. The projector is
designed to be lifted using the handrail at the base. Do not attempt to lift the 
projector by holding the front, the side covers or the lens.
Care should be taken when removing or attaching the projector feet to ensure that
the projector does not rest on its feet at an angle.
Never operate the projector with the cover removed and always switch off the
mains supply and disconnect the plug before removing the cover.
Never...

Pre-Installation Check
Before mounting the projector in its intended location, the following pre-installation
routine must be performed:
1. Install the projector lens.
2. Ensure all the air flow inlet and outlet ducts are clear from obstruction.
3. Insert the power cord securely into the socket on the rear panel of the projector 
and connect to an appropriate mains supply (refer to the specification label at 
the rear of projector).
4. Switch on the projector and wait for approximately 30 seconds.
5....

Remote Control Unit - Battery Installation
The Remote Control Unit can be powered by 4 AAA (HP16/RO3/LR03) alkaline
batteries or by direct connection to the projector via a remote receiver or hard wire.
The battery compartment is located on the back of the
Remote Control. To remove the compartment cover,
insert a finger-nail into the recess provided to the right
of the cover and push to the right. While pushing to the
right, lift out the left hand side of the cover.
Insert the first two new batteries as...

Remote Receiver
The optional remote receiver acts as a relay between
the remote control and the projector and is useful for
installations where the Infra Red signal from the
remote cannot reach the sensors on the projector.
The Infra Red signals from the remote control are
picked up by the IR receiver on the front of the
remote receiver and are relayed to the projector via
the 15 way high density D style connector on the
underside of the unit.
The remote receiver also allows direct cabling (hard
wiring)...

Hard Wired Remote Adapter
The hard wired remote adapter consist of two cables which connect together to form
a direct (hard wired) link between the remote control unit and the projector.
The longer of the two cables has with a 3.5mm stereo jack plug at one end which
connects into the top of the remote control unit.
The 3.5mm stereo jack plug has a long outer shell - some of which may be visible
when the plug is seated correctly in the Remote Control Unit. To avoid damage,
do not attempt to push the plug...

Projector Case
The projector covers are manufactured from tough ABS material which are attached
to a rigid alluminium space frame.
The projector should always be lifted using the handrail. Do not attempt to lift the
projector by holding the covers or the lens.
493mm
(19.40)450mm
(17.75)
744mm
(29.30)465mm
(18.30)
1125mm (44.30) 1035mm (40.75) 790mm (31.10)
AÑ9
Overview
Components
OVERVIEW
LBV00056; Revision A - 23/08/99