Digital Projection E-Vision 8000 Series User Guides

Digital Projection E-Vision 8000 series  MENU MAP Operating Guide
Page Op_22
Menu Map
Menu Sub Menus and Controls
INPUT
Input Selection  HDMI, DVI, VGA, Component/BNC, Composite, S-Video, 3G-SDI, Option Board
PIP
PIP Option  Off, On
PIP Input  Select from group B or group A
Position  Top Left, Top Right, Bottom Left, Bottom Right, Split L-R
Test Pattern  Off, Color Bars, Alignment Grid, Burst, Red, Green, Blue, White, Black, Cross Mark, Cross\
 Hatch + 
Mark, Corrected Red, Corrected Green, Corrected...

Digital Projection E-Vision 8000 series  MENU MAP Operating Guide
Page Op_23
LAMPS
Mode  Dual, Single
Power  Normal, Custom Power, Eco
High Altitude  Off, On
Custom Power Level 80-100%
Lamp Status  Information Only: Lamp 1 On, Off     Lamp 2 On, Off
 ALIGNMENT
Projection Mode  Front, Rear, Ceiling + Front, Ceiling + Rear
Fan Mode  Normal, Up, Down
Lens Control  Shift, Zoom/Focus
Lens Memory 
Load Memory  Memory 1-10
Save Memory  Memory 1-10
Center Lens  Press ENTER to execute
Warp
Keystone  Horizontal,...

Digital Projection E-Vision 8000 series  MENU MAP Operating Guide
Page Op_24
CONTROL
Eco Network Power   Standard, Eco
Auto Power Off   On, Off
Auto Power On   On, Off
Projector Control   RS232, Network
Network   Information only: IP Address, Subnet Mask, Gateway, DHCP
Startup Logo   On, Off
Trigger   Auto, 5:4, 4:3, 16:10, 16:9, 1.88, 2.35, Letterbox, Native, Unscaled
Auto Search   On, Off
Dynamic Black   On, Off
Language   Select from list
SERVICE
Information only:  Model, Serial Number, Software...

E-Vision 8000 Series
High Brightness Digital Video Projector
REMOTE COMMUNICATIONS GUIDE
Rev B September 2012  

Digital Projection E-Vision 8000 series  CONTENTS Remote Communications Guide
CONTENTS
Introduction ........................................................................\
...................Rem_1
Operation commands .........................................................................Rem_1
Key commands ....................................................................................Rem_1
The Operation Commands ...........................................................Rem_2
INPUT menu...

Digital Projection E-Vision 8000 series  INTRODUCTION Remote Communications Guide
Page Rem_1
Introduction
The projector can be controlled by using an external control system or a PC via a LAN or RS232 serial interface, using a terminal-emulation 
program, such as HyperTerminal.
Operation commands
Operation commands simulate menu operations and determine the settings o\
f the projector, and use the following format:
• All commands consist of ASCII text strings starting with the letters ‘op’, and ending...

Digital Projection E-Vision 8000 series  THE OPERATION COMMANDS Remote Communications Guide
Page Rem_2
The Operation Commands
Notes
INPUT menu
input.sel= ?0 = HDMI
1 = DVI
2 = VGA
3 = Component / BNC
4 = Composite
5 = S-Video
6 = 3G-SDI
Not applicable when Picture Mute is On.
pip= ?0 = Off
1 = On
pip.sel= ?1 = HDMI
2 = DVI
3 = VGA
4 = Component / BNC
5 = Composite
6 = S-Video
7 = 3G-SDI
Cannot be set to 0.
pip.swap(execute)Swap main and PIP sourceNot applicable without signal locked.
pip.pos= ?0 = Top...

Digital Projection E-Vision 8000 series  THE OPERATION COMMANDS Remote Communications Guide
Page Rem_3
...continued from previous page
Notes
pattern= ?0 = Color Bar
1 = Cross Hatch
2 = Burst
3 = Red
4 = Green
5 = Blue
6 = White
7 = Black
8 = Cross Mark
9 = Cross Hatch + Mark
10 = Red (TI)
11 = Green (TI)
12 = Blue (TI)
13 = HRamp (TI)
14 = Off
color.space= ?0  = Auto
1 = YCbCr
2 = YPbPr
3 = RGB-PC (0-255)
4 = RGB-Video (16-235)
Not applicable without signal locked.
input.lock= ?0  = Auto
1 = 48 Hz
2 = 50...

Digital Projection E-Vision 8000 series  THE OPERATION COMMANDS Remote Communications Guide
Page Rem_4
...continued from previous page
Notes
PICTURE menu
pic.mode= ?0 = High Bright
1 = Presentation
2 = Video
contrast= ? + -0 ~ 200Not applicable without signal locked.
dyna.cont= ?0 = Off
1 = On
Not applicable without signal locked.
bright= ? + -0 ~ 200Not applicable without signal locked.
saturat= ? + -0 ~ 200Not applicable without signal locked.
Only valid when the input is Composite or 
S-Video.
tint= ?...

Digital Projection E-Vision 8000 series  THE OPERATION COMMANDS Remote Communications Guide
Page Rem_5
...continued from previous page
Notes
blue.offset= ? + -0 ~ 200Not applicable without signal locked.
red.gain= ? + -0 ~ 200Not applicable without signal locked.
green.gain= ? + -0 ~ 200Not applicable without signal locked.
blue.gain= ? + -0 ~ 200Not applicable without signal locked.
sharpness= ? + -0 ~ 200Not applicable without signal locked.
nr= ? + -0 ~ 200Noise Reduction
Not applicable without signal...