Digital Projection E-Vision 8000 Series User Guides

Digital Projection E-Vision 8000 series  A TOUR OF THE MENUS Operating Guide
Page Op_12
LAMPS Menu
Mode
• Set this to Single or Dual as required.
When the mode is changed, it will not be possible to change it again within five minutes.
Power
• Set this to Normal for 100% power, Eco for 80% power or Custom to enable the 
Custom Power slider.
High Altitude Mode
• Set this to On if it is necessary to have the cooling fans running at high speed.
Custom Power Level
• Set the slider as required.
Lamp Status
•...

Digital Projection E-Vision 8000 series  A TOUR OF THE MENUS Operating Guide
Page Op_13
ALIGNMENT Menu
Projection Mode
• Front and Rear define whether the projector is in front of the screen or behind it. 
Set to Ceiling + Front or Ceiling + Rear if the projector is ceiling mounted.
Fan Mode
• Adjusts the fan speeds to optimise cooling when the projector is in vert\
ical orientation. 
Set to Up or Down as appropriate when projecting lens up or down.
Lens Control
• Press ENTER to display the Lens Control...

Digital Projection E-Vision 8000 series  A TOUR OF THE MENUS Operating Guide
Page Op_14
Lens Memor y sub menu
The current lens position, focus and zoom settings can be saved in one of ten memories, for 
later recall.
• Press ENTER to open the Lens Memory sub menu.
Save Memor y
• Press ENTER to open the Save Memory sub menu.
• Use and to select from Lens Memor y 1 to Lens Memor y 10.
• Press ENTER to save the current settings.
Load Memor y
• Press ENTER to open the Load Memory sub menu.
• Use and to...

Digital Projection E-Vision 8000 series  A TOUR OF THE MENUS Operating Guide
Page Op_15
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
 Only one of the Warp controls, or 
the Blanking control can be used 
at any one time.
  Exception: all four Corner controls 
can be used at the same time.
 If the Edge Blend feature is in 
use, then only the four Corner 
controls can be used.
 If you are not sure which Warp 
control is in use, then select Reset, 
from the War...

Digital Projection E-Vision 8000 series  A TOUR OF THE MENUS Operating Guide
Page Op_16
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
 Only one of the Warp controls, or 
the Blanking control can be used 
at any one time.
  Exception: all four Corner controls 
can be used at the same time.
 If the Edge Blend feature is in 
use, then only the four Corner 
controls can be used.
 If you are not sure which Warp 
control is in use, then select Reset, 
from the War...

Digital Projection E-Vision 8000 series  A TOUR OF THE MENUS Operating Guide
Page Op_17
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
 Only one of the Warp controls, or 
the Blanking control can be used 
at any one time.
  Exception: all four Corner controls 
can be used at the same time.
 If the Edge Blend feature is in 
use, then only the four Corner 
controls can be used.
 Black Level Uplift is available for 
up to two edges only, and they 
must be...

Digital Projection E-Vision 8000 series  A TOUR OF THE MENUS Operating Guide
Page Op_18
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
 Eco Network Power must be set to 
Standard, if you wish to control the 
projector via the LAN connection.
CONTROL menu
Eco Network Power
• Set this to Standard or Eco as required. In Eco mode, the LAN power supply is switched 
off.
Auto Power Off
• Set this to On, if you want the projector to go into Standby mode when no input...

Digital Projection E-Vision 8000 series  A TOUR OF THE MENUS Operating Guide
Page Op_19
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
 Eco Network Power must be set to 
Standard, if you wish to control the 
projector via the LAN connection.
 To change any of the network 
settings, use the embedded LAN 
IP Configuration Utility (see the 
Remote Communications Guide).
Projector Control
• Set this to Network or RS232 as required.
Network sub menu
• Press ENTER...

Digital Projection E-Vision 8000 series  A TOUR OF THE MENUS Operating Guide
Page Op_20
Startup Logo
• Set this to On if you want the DP logo to show when the projector is first switched on.
Trigger
• Set this to Auto if you want the Trigger output to be activated when the projector is first 
switched on.
• Set this to one of the Aspect Ratio settings, if you want the Trigger output to be 
activated when the projector is switched to that aspect ratio.
Auto Search
• When this is set to On, the projector...

Digital Projection E-Vision 8000 series  A TOUR OF THE MENUS Operating Guide
Page Op_21
SERVICE menu
Information
• The first part of the menu is for information only.
Blue Only
• Set this to On or Off as required.
Factor y Reset
• Projector will ask for confirmation before restoring all settings to factory defaults.
• When the confirmation box appears, use  or to move the blue highlight to OK 
or Cancel, then press ENTER to confirm your selection.
Notes
 See also Using the Menus, earlier 
in this guide...