Digital Projection E-Vision 8000 Series User Guides

Digital Projection E-Vision 8000 series  WIRING DETAILS Connection Guide
Page Conn_5
Wiring Details
Signal inputs and outputs
3G-SDI
75 ohm BNC
SMPTE 292 / HD-SDI signals are very high speed digital signals which req\
uire better quality 
coaxial cable than conventional analogue video. The data rate is 1.5 Gigabits per second.
In choosing cable length and connectors for any installation the frequen\
cy response loss 
in decibels should be proportional to √f, from 1MHz, to 1.5GHz.  The following or...

Digital Projection E-Vision 8000 series  WIRING DETAILS Connection Guide
Page Conn_6
DVI-D
24 way D-type connector
1 TMDS Data 2-
2 TMDS Data 2+
3 TMDS Data 2 Shield
4 unused
5 unused
6 DDC Clock
7 DDC Data
8 unused
9 TMDS Data 1-
10 TMDS Data 1+
11 TMDS Data 1 Shield
12 unused
13 unused
14 +5 V Power
15 Ground
16 Hot Plug Detect*
17 TMDS Data 0-
18 TMDS Data 0+
19 TMDS Data 0 Shield
20 unused
21 unused
22 TMDS Clock Shield
23 TMDS Clock+
24 TMDS Clock-
* Hot plug detect (HPD) is fully DVI compliant....

Digital Projection E-Vision 8000 series  WIRING DETAILS Connection Guide
Page Conn_7
VGA
15 way D-type connector
1 R
2 G
3 B
4 unused 
5 Digital Ground (H Sync)
6 R Ground
7 B Ground
8 G Ground
9 +5v
10 Digital Ground (V Sync/DDC)
11 unused
12 SDA
13 H Sync
14 V Sync
15 SCL
COMPONENT
5 x 75 ohm BNC
RGBHV  RGsB  YPbPr  YCbCr
Green     Green + Sync  Y    Y
Blue   Blue  Pb  Cb
Red   Red  Pr  Cr
Hsync
Vsync
Notes
 For full details of all input settings, 
see the INPUT menu in the 
Operating Guide.pin view of...

Digital Projection E-Vision 8000 series  WIRING DETAILS Connection Guide
Page Conn_8
S-Video input
4 pin mini-DIN
1 Y Ground
2 C Ground
3 Luminance (Y)
4 Chrominance (C)
Video input
1 x RCA Phono
Composite Video
pin view of female connector
Notes
 For full details of all input settings, 
see the INPUT menu in the 
Operating Guide. 
Rev B September 2012  

Digital Projection E-Vision 8000 series  WIRING DETAILS Connection Guide
Page Conn_9
Control connections
LAN connection
10BaseT Unshielded Twisted Pair cable
The standard wire colors are as follows:
1 White / Orange stripe
2 Orange
3 White / Green stripe
4 Blue
5 White / Blue stripe
6 Green
7 White / Brown stripe
8 Brown
Crossed cable
(used to connect directly to a computer with no hub or network.) 
(Note that only the green and orange pairs are crossed)
1 White / Orange stripe  White / Green stripe 1
2...

Digital Projection E-Vision 8000 series  WIRING DETAILS Connection Guide
Page Conn_10
RS232 Serial control input
1 unused
2 Received Data (RX)
3 Transmitted Data (TX)
4 unused
5 Signal Ground
6 unused
7 unused
8 unused
9 unused
Null-modem cable
(used to connect the projector to a computer)
RX 2 ---  3 TX
TX 3 ---  2 RX
GND 5 ---  5 GND
Wired Remote control connection
3.5mm mini jack
Tip Power
Ring Signal
Sleeve Ground
Screen Trigger output
3.5mm mini jack
Tip Signal
Sleeve Ground
Notes
 For full details...

E-Vision 8000 Series
High Brightness Digital Video Projector
OPERATING GUIDE
Rev B September 2012  

Digital Projection E-Vision 8000 series  CONTENTS Operating Guide
CONTENTS
Using the Remote Control ...............................................................Op_1
Test Pattern ....................................................................................Op_1
Using the Control Panel ....................................................................Op_2
Using the Menus ........................................................................\
............Op_3
Navigating the menus...

Digital Projection E-Vision 8000 series  CONTENTS Operating Guide
CONTROL menu ...................................................................................Op_18
Eco Network Power......................................................................Op_18
Auto Power Off .............................................................................Op_18
Auto Power On .............................................................................Op_18
Projector Control...

Digital Projection E-Vision 8000 series  USING THE REMOTE CONTROL Operating Guide
Page Op_1
Using the Remote ControlNotes
 Some options and controls may not 
be available due to settings in the 
menus.
 For full details of how to use the 
menu system, see later in this guide.
Test Pattern
• Press ENTER to display a Test Pattern.
• Use  or to scroll through the 
following Test Patterns:
... Off, Color Bars, Alignment Grid, Burst, Red, Green, Blue, White, Black, Cross Mark, Cross Hatch + Mark, Corrected...