Digital Projection E-Vision 6000 Series User Guides

Digital Projection E-Vision 6000 Series A TOUR OF THE MENUS Operating Guide
Op 9
Notes
Adjust menuImage Options tab
 PC adj. settings are used for 
Computer 1 signals only. Their 
range and default values depend on 
the input standard.
 Only use Fine Sync after you have 
adjusted the Total dots setting.
 When WXGA mode is set to On, 
XGA (1024 x 768) modes may not 
be displayed correctly.
Adjust menu continued...
Image Options
•	Screen 
Set the aspect ratio of the projected image. Choose from 4:3, 16:9,...

Digital Projection E-Vision 6000 Series A TOUR OF THE MENUS Operating Guide
Op 10
Adjust menu continued...
Video
•	Noise reduction 
Set the noise reduction level as required.
•	3D Y/C separation 
Switch this setting on to increase the separation of Y (brightness) from C 
(color).
•	Progressive 
Choose the Progressive conversion (deinterlacing) method.
•	Color matrix 
In most cases, the Auto setting determines the correct color space to 
use. If it does not, you can choose a specific color space:
•	RGB...

Digital Projection E-Vision 6000 Series A TOUR OF THE MENUS Operating Guide
Op 11
Volume control
Select Volume from the main menu to bring out the volume slider.
To exit the volume slider, press MENU or RETURN.
Setting menu
The Setting menu contains three tabs: Basic, Installation and Option.
Basic tab
•	Keystone 
Adjust horizontal and vertical keystone values.
•	Lamp control 
Choose between Normal and Eco. Using the Eco mode extends lamp 
life and reduces fan noise.
•	Lamp mode 
Choose whether you will...

Digital Projection E-Vision 6000 Series A TOUR OF THE MENUS Operating Guide
Op 12
Notes
Setting menuInstallation tab
 The Communication speed setting 
is not available if PC control is set 
to Network.
 Make a note of your password 
and keep it safe. If you are 
unable to retrieve the password, 
the projector can no longer be 
started. Contact your dealer for 
assistance.
 Key lock does not affect the remote 
control.
 DynamicBlack reduces the overall 
light output for images that contain 
a lot of...

Digital Projection E-Vision 6000 Series A TOUR OF THE MENUS Operating Guide
Op 13
Setting menu continued...
Installation tab - continued
•	RC sensor 
Controls whether the projector will use the infrared sensor at the front\
, the one at the back, or both.
•	Network setting 
This sub-menu allows you to adjust network settings.
•	Standby mode 
Choose between Normal and Power-saving standby mode. 
•	PC control 
Choose from PC Control (RS232) or Network (LAN) as the remote connection used for external...

Digital Projection E-Vision 6000 Series A TOUR OF THE MENUS Operating Guide
Op 14
Networksetting
Setting
DHCP EnableDisable
IP address 172.16 .7 .15
Subnet 255.255 .255 .0
Gateway EnableDisable
172 .16 .7 .201
DNS EnableDisable
172 .16 .1 .84
Apply settings
Notes
Setting menuInstallation tabNetwork setting
Setting menu continued...
Network setting sub-menu
The Network setting menu contains the following settings:
•	DHCP 
Set DHCP to Enable if the IP address is to be assigned by a DHCP 
server, or Disable...

Digital Projection E-Vision 6000 Series A TOUR OF THE MENUS Operating Guide
Op 15
Setting menu continued...
Option tab
•	Power management 
Set the amount of time the projector will remain on without an input 
source before going into standby mode.
•	Screen trigger 
Set this to On to enable the screen trigger.
•	Fan control 
Max increases the fan speed to compensate for reduced air density at 
high altitude.
•	Default input select 
If Default input select is set to Auto, the projector will cycle the...

Digital Projection E-Vision 6000 Series A TOUR OF THE MENUS Operating Guide
Op 16
Information menu
The information menu is arranged in four tabs: Usage time, Input, Network 
and Version.
Usage time tab
Displays information about lamp usage, projector running time and filter time.
Input tab
Displays information about the active source.
Network tab
Displays network information.
Version tab
Displays the model name and firmware version.
Reset menu
The Reset menu allows you to restore factory default...

Digital Projection E-Vision 6000 Series MENU MAP Operating Guide
Op 17
Menu Map
Menu Sub Menus and Controls
MAIN
Input, Adjust, Volume, Setting, Information, Reset
INPUT
Computer 1, Computer 2, Computer 3, Component, Video, S-Video
ADJUST
Image
Image select High-bright, Presentation, Video, Movie, Graphic, sRGB
Detail settings
 Basic
  Gamma Dynamic, Natural, Black detail
   Color temp. 5000K, 6500K, 7800K, 8500K, 9300K, 10500K
  BrilliantColor 1 ~ 3
 White balance
  Red 0 ~ 100 (50)
  Green 0 ~ 100...

Digital Projection E-Vision 6000 Series MENU MAP Operating Guide
Op 18
PC adj.
  Horizontal
  Vertical
  Total  dot
  Fine  sync
WXGA mode On, Off
Video
Noise reduction Off, Low, Mid, High
3D Y/C separation On, Off
Progressive Off, Still, Normal, Movie
Color matrix Auto, RGB, SDTV, HDTV
Film Off, 2-2, 2-3 Auto, 2-2 On, 2-3 On
VOLUME
0-61
SETTING
Basic
Keystone
  Horizontal -100 ~ 100 (0)
  Vertical -100 ~ 100 (0)
Lamp control Normal, Eco
Lamp mode Dual, Lamp1, Lamp2
Lamp interval Off, 1 week, 4 weeks,...