Dell Sx2210t Users Guide

Electrical  Specifications  
Physical  Characteristics  
Environmental  Characteristics  Video input signals Analog RGB, 0.7 Volts +/ -  5%, positive polarity at 
75 ohm input impedance  
Digital DVI - D TMDS, HDMI, 600mV for each 
differential line, positive polarity at 50 ohm input 
impedance
Audio Input and Output signals Input signal level: 1Vrms without chipping
Synchronization input signals Separate horizontal and vertical synchronizations, 
polarity - free TTL level, SOG (Composite SYNC on...

Maintenance Guidelines  
Cleaning Your Monitor  
For best practices, follow the instructions in the list below while unpacking, cleaning, or handling your monitor:  
l To clean your touch screen, use the supplied soft, clean cloth. Do not use benzene, thinner, ammonia, abrasive cleaners, or compressed air. Avoid 
wiping the top corners of the monitor where the optics are located.   
l Use a lightly - dampened, warm cloth to clean the monitor. Avoid using detergent of any kind as some detergents leave a...

Back to Contents Page    
 
Appendix   
SX2210T  Flat Panel Monitor Users Guide  
  Safety Instructions  
  FCC Notice (U.S. Only) and Other Regulatory Information   
  Contacting Dell  
    
CAUTION: Safety Instructions  
For information on safety instructions, see the safety information that shipped with your monitor.  
FCC Notices (U.S. Only) and Other Regulatory Information  
For FCC notices and other regulatory information, see the regulatory compliance website located at  www.dell.com...

Back to Contents Page    
Setting Up Your Monitor   
 
 
1. Go to  http://support.dell.com ,  enter your service tag, and download the latest driver for your graphics card.   
2. After installing the drivers for your graphics Adapter, attempt to set the resolution to  1920 X 1080  again.  
Back to Contents Page  NOTE:  If you are unable to set the resolution to 1920 x 1080, please contact Dell™ to inquire about a graphics Adapter that supports these resolutions.    

Back to Contents Page    
Setting Up Your Monitor   
SX2210T  Flat Panel Monitor  
 
1. Right - click on the desktop and click  Properties .  
2. Select the  Settings  tab.  
3. Select  Advanced .  
4. Identify your graphics controller supplier from the description at the top of the window (e.g. NVIDIA, ATI, Intel etc.).   
5. Refer to the graphic card provider website for updated driver (for example,  http://www.ATI.com  OR  http://www.NVIDIA.com  ).  
6. After installing the drivers for your graphics...

Back to Contents Page    
Operating the Monitor   
SX2210T  Flat Panel Monitor Users Guide  
   Turn On the Monitor  
   Using the Front Panel Controls  
   Using the On - Screen Display (OSD) Menu  
   Setting the Maximum Resolution  
   Using the Dell Soundbar (Optional)  
   Using the Tilt  
   Using the Camera   
   Installing and Using the Facial Recognition Software (FastAccess)  
   Using the Touch Screen  
   
Turn On the Monitor  
Press the    button to turn on the monitor...

Front panel button  
Use the buttons  on the side of the monitor to adjust the image settings.   
               
   
Using the On - Screen Display (OSD) Menu  
Accessing the Menu System  Exit Use the Exit  button  to exit on - screen display (OSD) from menu and sub - menus.  
Front panel Button Description  
A
Up  Use the Up button to adjust (increase ranges) items in the OSD menu.
B  
Down  Use the Down button to adjust (decrease ranges) items in the OSD menu.
C   
OK    
Use the OK button to confirm...

   
The table below provides a list of all the OSD menu options and their functions.    
2.  
Press the   and   buttons to toggle between options in the Menu. As you move from one icon to another, the option name is highlighted.   
3.  
To select the highlighted item on the menu press the   again.   
4.  
Press the   and   buttons to select the desired parameter.   
5.  
Press the   buttons to enter the slide bar and then use the   or   button, according to the indicators on the menu, to make your...

   
 
 
    Auto Adjustment allows the monitor to self - adjust to the incoming video signal. After using Auto Adjustment, you can further tune 
your monitor by using the Pixel Clock (Coarse) and Phase (Fine) controls under Image Settings.  
 
    NOTE:   Auto Adjust does not occur if you press the button  while there are no active video input signals or attached cables .  
  Input Source   Use the Input Source menu to select different video signals that may be connected to your monitor....

 
Back  
Press the   button to go back to the main menu.  
    Input Color Format   Allows you to set the video input mode to:   
l RGB : Select this option if your monitor is connected to a computer or DVD player using the HDMI cable or the HDMI to DVI 
adapter.   
l YPbPr : Select this option if your DVD player supports only YPbPr output.   
 
Mode Selection   Allows you to set the display mode to:   
l Graphics : Select this mode if your monitor is connected to your computer.   
l Video : Select this...