Dell Sx2210t Users Guide

							Electrical  Specifications  
Physical  Characteristics  
Environmental  Characteristics  Video input signals Analog RGB, 0.7 Volts +/ -  5%, positive polarity at 
75 ohm input impedance  
Digital DVI - D TMDS, HDMI, 600mV for each 
differential line, positive polarity at 50 ohm input 
impedance
Audio Input and Output signals Input signal level: 1Vrms without chipping
Synchronization input signals Separate horizontal and vertical synchronizations, 
polarity - free TTL level, SOG (Composite SYNC on 
green)
AC/DC Adaptor input voltage/frequency/current 100 to 240 VAC/50 or 60 Hz  +  3 Hz/1.6A (Max.) 
 For use only with power supply DELL, 
DA65NS4 - 00.  
Inrush current 120 V: 30 A (Max.)  
240 V: 60 A (Max.) 
Connector type 15 - pin D - sub miniature, blue connector; DVI - D, white connector; 
HDMI, Black connector
Signal cable type Digital: Detachable, DVI - D, Solid pins, shipped detached from the 
monitor 
Analog: Detachable, D - Sub, 15pins, shipped attached to the 
monitor  
HDMI: Detachable, HDMI - A, Solid pins, shipped without cable  
Dimensions (with stand)
Height  401.8 mm (15.82 inches)
Width 551.5 mm (21.71 inches)
Depth 194.3 mm (7.61 inches)
Dimensions (without stand)
Height  342.1 mm (13.47 inches)
Width 551.5 mm (21.71 inches)
Depth 92.3 mm (3.63 inches)
Stand dimensions
Height  257.5 mm (10.14 inches)
Width 228.7 mm (9.00 inches)
Depth 193.4 mm (7.61 inches)
Weight
Weight with packaging 9.11 kg (20.04 lbs)
Weight with stand assembly 
and cables 7.68 kg (16.90 lbs)
Weight without cable assembly 6.98 kg (15.36 lbs)
Weight of stand assembly 1.93 kg (4.25 lbs)
Temperature  
Operating 0° to 40° C (32° to 104°Fyf
Non - operating Storage:  - 20° to 60° C ( - 4° to 140° Fyf  
Shipping:  - 20° to 60° C ( - 4° to 140° Fyf
Humidity
Operating 10% to 80% (non - condensing)  
						

							Maintenance Guidelines  
Cleaning Your Monitor  
For best practices, follow the instructions in the list below while unpacking, cleaning, or handling your monitor:  
l To clean your touch screen, use the supplied soft, clean cloth. Do not use benzene, thinner, ammonia, abrasive cleaners, or compressed air. Avoid 
wiping the top corners of the monitor where the optics are located.   
l Use a lightly - dampened, warm cloth to clean the monitor. Avoid using detergent of any kind as some detergents leave a milky film on the monitor.    
l Handle your monitor with care; any scratch on the monitor will show scuff marks.    
l To help maintain the best image quality on your monitor, use a dynamically changing screen saver and turn off your monitor when not in use.   
Back to Contents Page  Non - operating Storage: 20% to 80% (non - condensing)  
Shipping: 20% to 80% (non - condensing)
Altitude
Operating 3,657.60 m (12,000 ft) max
Non - operating 12,192 m (40,000 ft) max
Thermal dissipation 222.3 BTU/hour (maximum)  
188.1 BTU/hour (typical)
CAUTION: Read and follow the  safety instructions  
						

							Back to Contents Page    
 
Appendix   
SX2210T  Flat Panel Monitor Users Guide  
  Safety Instructions  
  FCC Notice (U.S. Only) and Other Regulatory Information   
  Contacting Dell  
    
CAUTION: Safety Instructions  
For information on safety instructions, see the safety information that shipped with your monitor.  
FCC Notices (U.S. Only) and Other Regulatory Information  
For FCC notices and other regulatory information, see the regulatory compliance website located at  www.dell.com
egulatory_compliance .  
Contacting Dell  
For customers in the United States, call 800 - WWW - DELL (800 - 999 - 3355).  
Dell provides several online and telephone - based support and service options. Availability varies by country and product, and some services may not be 
available in your area. To contact Dell for sales, technical support, or customer service issues:  
 
Back to Contents Page  CAUTION: Use of controls, adjustments, or procedures other than those specified in this documentation may result in exposure to shock, 
electrical hazards, and/or mechanical hazards. 
NOTE:  If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or 
Dell product catalog. 
1. Visit   support.dell.com . 
2.  Verify your country or region in the  Choose A Country/Region  drop - down menu at the bottom of the page. 
3. Click  Contact Us  on the left side of the page.
4. Select the appropriate service or support link based on your need.
5.  Choose the method of contacting Dell that is convenient for you.  
						

							Back to Contents Page    
Setting Up Your Monitor   
 
 
1. Go to  http://support.dell.com ,  enter your service tag, and download the latest driver for your graphics card.   
2. After installing the drivers for your graphics Adapter, attempt to set the resolution to  1920 X 1080  again.  
Back to Contents Page  NOTE:  If you are unable to set the resolution to 1920 x 1080, please contact Dell™ to inquire about a graphics Adapter that supports these resolutions.    
						

							Back to Contents Page    
Setting Up Your Monitor   
SX2210T  Flat Panel Monitor  
 
1. Right - click on the desktop and click  Properties .  
2. Select the  Settings  tab.  
3. Select  Advanced .  
4. Identify your graphics controller supplier from the description at the top of the window (e.g. NVIDIA, ATI, Intel etc.).   
5. Refer to the graphic card provider website for updated driver (for example,  http://www.ATI.com  OR  http://www.NVIDIA.com  ).  
6. After installing the drivers for your graphics adapter, attempt to set the resolution to  1920 X 1080  again.  
   
Back to Contents Page  NOTE:  If you are unable to set the resolution to 1920 x 1080, please contact the manufacturer of your computer or consider purchasing a graphics 
adapter that will support the video resolution of 1920 x 1080.      
						

							Back to Contents Page    
Operating the Monitor   
SX2210T  Flat Panel Monitor Users Guide  
   Turn On the Monitor  
   Using the Front Panel Controls  
   Using the On - Screen Display (OSD) Menu  
   Setting the Maximum Resolution  
   Using the Dell Soundbar (Optional)  
   Using the Tilt  
   Using the Camera   
   Installing and Using the Facial Recognition Software (FastAccess)  
   Using the Touch Screen  
   
Turn On the Monitor  
Press the    button to turn on the monitor  
           
   
Using the Front Panel Controls    
Use the buttons on the front of the monitor to adjust the image settings.   
             
Front panel button Description  
A  
Preset modes    
Use the Preset modes button to choose from a list of preset color modes. See  Using the OSD Menu .  
B  
Brightness / Contrast  Use the Brightness / Contrast button to direct access to the Brightness and Contrast control menu.
C  
Menu    
Use the Menu button to open the on - screen display OSD).  
D        
						

							Front panel button  
Use the buttons  on the side of the monitor to adjust the image settings.   
               
   
Using the On - Screen Display (OSD) Menu  
Accessing the Menu System  Exit Use the Exit  button  to exit on - screen display (OSD) from menu and sub - menus.  
Front panel Button Description  
A
Up  Use the Up button to adjust (increase ranges) items in the OSD menu.
B  
Down  Use the Down button to adjust (decrease ranges) items in the OSD menu.
C   
OK    
Use the OK button to confirm your selection.  
D  
Back     
Use the back button to go back to the main menu. 
  NOTE:  If you change the settings and then either proceed to another menu or exit the OSD menu, the monitor automatically saves the changes. The 
changes are also saved if you change the settings and then wait for the OSD menu to disappear.
 
1.  
Press any key to launch the OSD menu and press   to display the main menu.   
Main Menu     
						

							   
The table below provides a list of all the OSD menu options and their functions.    
2.  
Press the   and   buttons to toggle between options in the Menu. As you move from one icon to another, the option name is highlighted.   
3.  
To select the highlighted item on the menu press the   again.   
4.  
Press the   and   buttons to select the desired parameter.   
5.  
Press the   buttons to enter the slide bar and then use the   or   button, according to the indicators on the menu, to make your changes.   
6.  
Select the   to return to previous menu without accepting current settings or   to accept and return to previous menu.   
Icon   Menu and Submenus Description
  BRIGHTNESS/CONTRAST   Use the Brightness and Contrast menu to adjust the Brightness/Contrast.   
   
   
 
 
Back  
Press the   button to go back to the main menu.  
 
Brightness   Allows you to adjust the brightness or luminance of the backlight.   
Press the    button to increase brightness and press the   button to decrease brightness (min 0 ~ max 100).   
 
Contrast   Allows you to adjust the contrast or the degree of difference between darkness and lightness on the monitor screen. Adjust 
brightness first, and adjust contrast only if you need further adjustment.  
Press the   button to increase contrast and press the   button to decrease contrast (min 0 ~ max 100).   
  Auto Adjust    Use this button to activate automatic setup and adjust menu. The following dialog appears on a black screen as the monitor self
adjusts to the current input:     
						

							   
 
 
    Auto Adjustment allows the monitor to self - adjust to the incoming video signal. After using Auto Adjustment, you can further tune 
your monitor by using the Pixel Clock (Coarse) and Phase (Fine) controls under Image Settings.  
 
    NOTE:   Auto Adjust does not occur if you press the button  while there are no active video input signals or attached cables .  
  Input Source   Use the Input Source menu to select different video signals that may be connected to your monitor.   
   
 
 
    
Press the   button to go back to the main menu  
 
   
Select VGA input when you are using the analog (VGA) connector. Press the   button to select the VGA input source. 
 
    
Select DVI - D input when you are using the digital (DVI) connector. Press the   button to select the DVI input source.  
Select HDMI input when you are using the digital (HDMI) connector.  Press the   button  to select the HDMI input source.
Select Auto select to let the monitor search for available input signals.   
  COLOR SETTINGS   Use the  Color Setting  menu to adjust the monitor's color settings.  
   
 
Color setting mode 
submenu   
       
						

							 
Back  
Press the   button to go back to the main menu.  
    Input Color Format   Allows you to set the video input mode to:   
l RGB : Select this option if your monitor is connected to a computer or DVD player using the HDMI cable or the HDMI to DVI 
adapter.   
l YPbPr : Select this option if your DVD player supports only YPbPr output.   
 
Mode Selection   Allows you to set the display mode to:   
l Graphics : Select this mode if your monitor is connected to your computer.   
l Video : Select this mode if your monitor is connected to a DVD player.   
NOTE:  Depending upon the Display Mode, select the Preset Modes available for your monitor change.  
    Preset Mode   Allows you to choose from a list of preset color modes.   
In the  Graphics  mode, you can set the color to the following preset values:   
l Standard : Loads the monitors default color settings. This is the default preset mode.   
l Multimedia : Loads color settings ideal for multimedia applications.   
l Game : Loads color settings ideal for most gaming applications.   
l Warm : Increase the color temperature. The screen appears warmer with a red/yellow tint.   
l Cool : Decreases the color temperature. The screen appears cooler with a blue tint.   
l Custom (RGB) : Allows you to manually adjust the color settings. Press the    and    buttons to adjust the Red, Green, 
and Blue values and create your own preset color mode.   
In the  Video  mode, you can set the color to the following preset values:  
l Movie : Loads color settings ideal for movies. This is the default preset mode.   
l Game : Loads color settings ideal for most gaming applications.   
l Sports : Loads color settings ideal for sports.   
l Nature:  Loads color settings ideal for nature.   
  Hue
Allows you to adjust the skin tone of the image. Use   or   button to adjust the hue from 0 to 100. 
NOTE:  Hue adjustment is available only in the  Video  mode.  
  Saturation
Allows you to adjust the color saturation of the image. Use   or   button to adjust the saturation from 0 to 100. 
NOTE:  Saturation adjustment is available only in the  Video  mode.  
  Demo Mode Vertically splits the screen into two segments. The left half of the screen in the normal mode and the right half of the screen is 
displayed in the color enhanced mode.   
 
NOTE:  Demo Mode is only available for video input.  
 
Reset Color Settings   Resets your monitors color settings to the factory defaults.  
  DISPLAY  SETTINGS