Dell Sx2210t Users Guide

							 
Display setting mode 
submenu   
   
 
 
Back  
Press the   button to go back to the main menu.  
    Horizontal  position  
Use the   and   buttons to adjust image left and right (min 0 ~ max 100).   
NOTE:  When using DVI or HDMI source, the Horizontal Position setting is not available.   
    Vertical Position  
Use the   and   buttons to adjust image up and down (min 0 ~ max 100).   
NOTE:  When using DVI or HDMI source, the Vertical Position setting is not available.   
    Pixel Clock   T he Phase and Pixel Clock adjustments allow you to adjust your monitor to your preference. These settings are accessed through the 
main OSD menu, by selecting Display Settings.    
Use  the    and    buttons to adjust for best image qua lity.  
    Phase   If satisfactory results are not obtained using the phase adjustment, use the Pixel Clock (coarse) adjustment and then use Phase 
(fine).   
NOTE:  Pixel Clock and Phase Adjustments are only available for VGA input.   
    Sharpness   Allows you to increase or decrease the sharpness of the image.   
Use    and   buttons to adjust the sharpness from 0 to 100.   
 
Dynamic Contrast   The dynamic contrast helps get a higher contrast if you choose Game preset, Movie preset, Sports preset and Nature preset. 
Use the   button to enable the Dynamic Contrast adjustment.   
Use the   button to disable the Dynamic Contrast adjustment.  
    
NOTE:  Brightness control is disabled in Dynamic Contrast mode.  
 
Response Time   Response time is the time required for an LCD pixel to change from fully active (black) to fully inactive (white), then back to fully active 
again.   
You can set the response time to:   
l Normal    
l Overdrive  (default).   
 
Reset Display Settings   Resets the monitors display settings to the factory defaults.  
  AUDIO SETTINGS   Use the  Audio Settings  menu to adjust the audio settings.  
						

							  Audio Setting mode 
submenu 
 
Line Out Source Select the source of the audio input. 
  Power Save Audio
Allows you to turn on or off the power to the audio during the audio power save mode.  
Default is On.  
On   —   Allows you to turn off the line - out to the sound bar during monitor standby.  
Off   —   Allows you to turn on the line - out to the sound bar during monitor standby.   
 
Reset Audio Setting   Resets your monitor audio settings to the factory defaults.
    Exit Menu  
Press the   button  to exit the OSD main menu and Press the   button to accept changes.  
  OTHER SETTINGS  
     
   
 
Back  
Press the   button to go back to the main menu.  
   
Language   Allows you to set the OSD display to one of six languages: English, Espanol, Francais, Deutsch, Simplified Chinese or Japanese.
    Menu Transparency   Allows you to adjust the OSD background from opaque to transparent.  
    Menu Timer   Allows you to set the time for which the OSD remains active after you press a button on the monitor.  
Use the   and   buttons to adjust the slider in 1 second increments, from 5 to 60 seconds.   
 
Menu Lock  
Controls user access to adjustments. When  Lock  is selected, no user adjustments are allowed. All buttons are locked except the
button.  
NOTE:  When the OSD is locked, pressing the   button takes you directly to the OSD settings menu, with OSD Lock pre
on entry. Choose  Unlock  and allow user access to all applicable settings.   
   
						

							 
DDC/CI     DDC/CI (Display Data Channel/Command Interface) allows a software on your computer to adjust the monitor display settings like 
the brightness, color balance etc.  
Enable  (Default): Optimizes the performance of your monitor and provides a better customer experience.  
Disable : Disables the DDC/CI option and the following message appears on the screen.  
   
 
 
Select  Yes  to disable DDC/CI or  No  to return.  
 
LCD Conditioning   LCD conditioning helps eliminate any image retention and may take several hours.  
NOTE:  Severe cases of image retention are known as burn - in. LCD Conditioning does not remove burn - in.  
Disable : This is the default option.  
Enable : Enables LCD conditioning and the following message appears on the screen. Select  Yes  to proceed and  No  to return.
   
  
 NOTE:  Press any button on the monitor to terminate LCD Conditioning at any time.   
 
Factory Reset   Resets all OSD settings to the factory preset values.    
						

							OSD Warning Messages    Personalize  
Allows you to adjust shortcut button for: 1. Brightness & Contrast and 2. Preset Modes.  
The following warning messages may appear on the screen to indicate that the monitor is out of synchronization.
 
 
 
This means that the monitor cannot synchronize with the signal that it is receiving from the computer. Either the signal is too high or too low 
for the monitor to use. See  Specifications  for the Horizontal and Vertical frequency ranges addressable by this monitor. Recommended mode 
is 1920 X 1080 at 60Hz. 
 
When monitor enters Power Save mode, one of the following messages appears :  
   
						

							See  Solving Problem  
s  for more information.  
Setting the Maximum Resolution  
To set the maximum resolution for the monitor:  
1. Right - click on the desktop and select  Properties .   
2. Select the  Settings  tab.   
3. Set the screen resolution to 1920 x 1080.   
4. Click  OK .   
If you do not see 1920 x 1080 as an option, you may need to update your graphics driver. Depending on your computer, complete one of the following 
procedures:  
l If you have a Dell desktop or portable computer: 
Go to  support.dell.com , enter your service tag, and download the latest driver for your graphics card.   
l If you are using a non - Dell computer (portable or desktop):
Go to the support site for your computer and download the latest graphic drivers.   
Go to your graphics card website and download the latest graphic drivers.   
Using the Dell Soundbar (Optional)    
If you press any button other than the Power button one of the following messages will appear depending on the selected input:
 
   
						

							The Dell Soundbar is a stereo two channel system, mountable on Dell Flat Panel Displays. The Soundbar has a rotary volume and on/off control to adjust the 
overall system level, a LED for power indication, and two audio headset jacks.  
 
Using the Tilt  
Tilt  
With the built - in stand, you can tilt the monitor for the most comfortable viewing angle.  
 1. Attach mechanism 
2.   Headphone connectors 
Power indicator 
4.   Power/Volume control
NOTE:  The stand is attached when the monitor is shipped from the factory.  
						

							Using the Camera   
Installing the Dell TouchCam Software (Microsoft   Windows   Operating Systems)  
The Dell SX2210T  webcam application media that shipped with your monitor, allows you to install the software and drivers for the integrated webcam.   
To install the  Dell TouchCam Software :  
You are now ready to use the Webcam.  
Using the TouchCam Software  
Stand - alone mode  
Stand - alone mode can be launched from the start menu.  
 
IM mode  
   
IM mode will launch itself automatically when an instant messaging program begins a video call session.  1. Insert the Dell  Drivers and Documentation  CD into the drive.
NOTE:  Ensure that the USB cable is connected between the monitor and the computer. 
2.  Choose  TouchCam Software .
3.  The  Install Shield Wizard  automatically launches the setup application. Click  Next  to continue.
4.  Read  Software License Agreement  and click  Yes  to continue. Click  Next  to continue.
5.  Click  Next  to continue.
6.  Click  Finish  to complete installation.
NOTE:  All instant messaging softwares have to close before the installation can begin.  
						

							 
When a video session ends, the TouchCam software will return to stand - alone mode.  
Setting up TouchCam in instant messaging programs  
The following describes the setup procedures for Windows Live Messenger.  
1. Click  Tool Audio and video setup...  
   
2. Select  Dell Web Camera Filter .   
						

							   
Similar setup steps can be performed in other IM programs.  
Installing and Using the Facial Recognition Software (FastAccess)    
Installing the Facial Recognition Software (FastAccess) (Windows Vista and Window 7 Operating Systems Only )  
To install the  Facial Recognition Software (FastAccess) :
You are now ready to use the Facial Recognition Software.  
First Use  
1. From the Start Menu; click Start All Programs FastAccess Configure FastAccess.     
2. Follow the on - screen setup wizard to begin using FastAccess face recognition.   
3. FastAccess automatically learns your face when you login to Vista or Windows 7. You will be able to log in to your computer automatically on most 
occasions, without having to enter a password.   
Customizing FastAccess  
To help keep FastAccess secure, features affecting overall system security and certain advanced features can only be changed if you have Vista administrator 
rights.   
l Configuration Console:  Allows changing the Security Level, Web Logins and Advanced features. Only administrator accounts have access to the 
Configuration Console.    
l User Settings:  Allows changing Web Logins and Notification Messages. Only Vista user accounts have access to User Settings.   
Configuration Console: Security    
The main security features of FastAccess are controlled by the Security Level Adjustment slider. As you move the slider from left to right, you turn on 
FastAccess and add increasing levels of security. As you move this slider, a brief description of the operating modes are displayed below the slider. You may 
set the following four security levels:    
1. Disabled   
2. Face Login (Factory default setting)   
3. User Switching   
4. Continuous Security    1. Insert the Dell   Drivers and Documentation   CD into the drive.
NOTE:  Ensure that the USB cable is connected between the monitor and the computer. 
2.  Choose   Facial Recognition Software  .
3.  The  Install Shield Wizard  automatically launches the setup application. Select the  Language  and click  Next  to continue.
4.  Read  Software License Agreement  and click  Yes  to continue.
5.  Click  Browse  to change  Destination Folder  where the software will be installed to and then click  Next  to continue.
6.  Choose  Full Installation  than click  Next  and follow the instructions to complete the installation. Alternatively, choose  Custom Installation  to select the 
components to install.
7. Click  Finish  to restart the computer after installation completes.   
						

							OK button : This button closes the Console and saves all changes.    
Cancel button : This button closes the Console without saving any changes.  
Choosing the Desired Webcam for Face Recognition  
l Automatic Webcam Selection:  Automatic Webcam Selection simplifies operation if more than one webcam is installed on your computer. FastAccess 
connects to a Dell Monitor webcam first.   
l Manual Webcam Selection:  Your desired webcam can be selected by opening the FastAccess Configuration Console and clicking the Advanced 
button. Next click the Camera Selection link and select the desired webcam.    
Using the Automatic Web Login  
The Web Login Vault feature allows FastAccess to remember user names and passwords for many of the websites that require a login. The Web Login 
Vault will automatically enter the user name and password for a website.  
The first time you enter a user name and password into a website with a login, FastAccess will present a small pop - up box. This box allows you to Keep On or 
Turn Off the Web Login Vault.  
Security Recommendations  
We recommend FastAccess be set to use the "Face + Password" feature.  Face + Password periodically requires your password in addition to your face.  This 
provides better security than any biometric or password alone.  
Using the Touch  Screen  
The Dell™ SX2210T Flat Panel Monitor is touch sensitive — you can control the computer simply by touching the screen.  
The touch screen allows you to interact with the computer in a similar way to a mouse as follows:  
l Tap the screen once for a single mouse click.   
l Tap the screen twice in quick succession for a double mouse click.   
l Touch down and then move your finger to drag an object.   
l Touch and hold for a right mouse click.   
l To select a menu option, touch down on the menu, then move your finger to the required option, then lift your finger to select the option. Alternatively, 
tap the menu, then tap the option required as you do with a mouse.   
The touch screen does not require pressure to sense a touch. For best results, point at roughly right angles to the screen and keep the rest of your hand clear 
of the glass.  
Using the Touch Screen Tools  
The Touch Screen Tools provides restore to factory defaults, diagnostic and calibrating functions that can be used for troubleshooting touch - screen problems.  
To install the  Touch Screen Tools  software:  
You are now ready to use the  Touch Screen Tools  Software and the Touch Screen Gestures.
Once installed, the  Touch Screen Tools  has an icon in the task bar that allows you to access the  Touch Screen Tools Settings .  
 
Touch Screen Tools Settings  
 
If the cursor does not move correctly when you touch the screen, see  Touch Screen problems .  NOTE:  Ensure that the USB cable is connected between the monitor and the computer. 
1. Insert the Dell  Drivers and Documentation  CD into the drive.
NOTE:  Ensure that the USB cable is connected between the monitor and the computer. 
2.  Choose  Touch Screen Tools .
3.  Follow the on - screen instructions to install  Touch Screen Tools  software.