Dell Projector S500/S500wi User Manual

							Using Your Projector81
2Actuate frame rate could be different depending on factors such as network 
environment, image content, signal conditions, locations, and CPU 
performance.
3Under clean WLAN environment using 802.11g connection, and no screen 
stretching.
4Compressed to 1024 x 768 and under 802.11g.
 
NOTE: Your computer will not enter S1 (standby mode) / S3 (sleep mode) / S4 
(hibernate mode) when running a wirel ess, USB Display, or USB Viewer 
presentation.
Using the Menu
Click   to display the menu.
W
EB MANAGEMENT—Click to open the Web Manage ment page. See Managing the 
Projector From Web Management on page 88.
SEARCH FOR PROJECTOR—Click to search and connect to wireless projector.
MAKE APPLICATION TOKEN—Click to make application token. See Make 
Application Token on page 107.
INFO—Click to display system information.
ABOUT—Click to display the application version.
EXIT—Click to close the application. 
						

							82Using Your Projector
Presentation to Go (PtG) Installation
Minimum system requirements to install PtG are as follow:
Operating System:
-Windows
Microsoft Windows XP™ Home or Professional Service pack 2/3 32-bit 
(recommended), Windows
® Vista 32-bit, and Windows® 7 Home or Professional 
32-bit or 64-bit
- Office 2003 and Office 2007
 
NOTE: Presentation to Go (PtG) installation  steps are the same for the S500 and 
S500wi models.
In order to use your USB Viewer, you need to complete the steps below: 1 Enable Wireless/LAN function on the  projector. See Wireless/LAN Settings 
(in LAN Mode) on page 62.
 
NOTE: When you start wireless, please wait about 50 seconds to reboot the 
Wireless / Network.
2 Plug the USB Flash to your projector.
 
NOTE: 
• Only supports the JPEG format phot o within 10 Mb x 40 M pixels.
• The PtG converter can convert your PowerPoi nt files into PtG files. See PtG 
Converter - Lite Application Software on page 86
• You can download the PtG Converter - Lite from Dell Support site at: 
support.dell.com.
3 On INPUT SOURCE  menu, select Multuple Display  and then select USB 
Vi e w e r  on the sub-menu. See INPUT SOURCE MULTIPLE DISPLAY on 
page 52. The  Presentation to Go Screen  appears: 
						

							Using Your Projector83
PtG Viewer
System will stay in this page when ready.
Photo Viewer 
						

							84Using Your Projector
PtG/Photo Function Introduction
Show valid PtG and Photo files which are stored in the USB disk.
 
NOTE: If only one disk is detected, t he system will skip this step.
PtG Overview 
						

							Using Your Projector85
Photo Overview
 NOTE: Supports 14 languages of photo file s name format (Languages: English, 
Dutch, French, German, Italian, Japanese,  Korean, Polish, Portuguese, Russian, 
Simplified Chinese, Spanish, Swed ish, and Traditional Chinese).
Buttons Introduction
Use the up, down  and left buttons to navigate and   button on your projectors 
control panel or remote control to select.
 
NOTE: If you enter the OSD menu while usi ng PtG, PtG navigation by the up, 
down, and left buttons will not function.
Button
Up Down Left Right  Enter 
PtG function Up Down Back No function Enter
PtG Playback Pre Page Next Page Back No function Next Pause
Photo 
function Up Down Back No function Enter
Photo 
Playback Pre  Pa g e N ex t  Pa g e B a c k N o  f u n c t i o n N o  
function 
						

							86Using Your Projector
Set up PtG Converter - Lite
Please follow the on-screen instructions to complete the setup.
PtG Converter - Lite  Application Software
Please launch the PtG Converter - Lite. The below screen appears:
1 Click   to start conversion.
2 Select the PowerPoint file you want to convert. 
						

							Using Your Projector87
3Click Browse button to select the storage location and then press OK.
 
NOTE: 
1
If your computer does not have MS PowerP oint installed, file convert will fail.
2PtG converter only supports up to 20 pages.
3PtG converter only supports conversion of .ppt files to .PtG files. 
						

							88Using Your Projector
Managing the Projector From Web 
Management
Configuring the Network Setting
If the projector is connected to a network, you can access the projector using a web 
browser. For configuring the network settin g, refer to Wireless/LAN Settings on 
page 62.
Accessing Web Management
Use Internet Explorer 5.0 and above or Firefox 1.5 and above and enter the IP 
address. You can now access Web Management and manage the projector from a 
remote location.
 
NOTE: Web management and set are the same for the S500 and S500wi 
models. 
Home Page
• Access the Web Management Home page  by entering the projector’s IP 
address at the web browser. See W ireless/LAN Settings on page 62.
• Select the language for web management from the list.
• Click any menu item on the left tab to access the page. 
						

							Using Your Projector89
Download the Wireless Application Software
See also Wireless Networking Installation on page 73.
Click the Download  button of the corresponding operating system of your 
computer. 
						

							90Using Your Projector
Conference Control
This allows you to host conference presentations from different sources without 
using projector cables and lets you control how each presentation will appear on 
screen.
 
NOTE: Without Conference Play Cont rol, the last user to hit the Play button on 
the application will take control of the full-screen projection.
Computer Name : Lists the computers logged for conference control.
Play Control : Click the buttons to control ho w each computer’s projection will 
appear on screen.
•  Full screen projection — The presentation from the computer occupies the whole screen.
•  Split 1 - The presentation from the computer appears on the upper  left corner of the screen.
•  Split 2- The presentation from the computer appears on the upper  right corner of the screen.
•  Split 3- The presentation from the computer appears on the lower  left corner of the screen.
•  Split 4- The presentation from the computer appears on the lower  right corner of the screen.
•  Stop - Projection from the computer is stopped.
IP Address : Shows each computer’s IP Address.
 
NOTE: To end the conference, click  Home.