Dell Projector S500/S500wi User Manual

							Using Your Projector91
Managing Properties
Admin
An administrator password is requ ired to access the Admin page. 
• Admin Password : Enter the administrator password and then click  Login. 
The default password is admin. To change the password, see Change 
Passwords on page 96. 
						

							92Using Your Projector
System Status
Displays the  Network Status , Connection Status , and Projector Status  
information. 
						

							Using Your Projector93
Network Status
See OSD section on page 62.
IP Setup
• Choose  Obtain an IP a ddress automatically  to assign an IP address to the 
projector automatically, or  Use the following IP address  to assign an IP 
address manually.
DHCP Server Setup • Choose  Auto to automatically set up the  Start IP, End IP , Subnet Mask, 
Default Gateway , and DNS Server  address from a DHCP server, or  Disable 
to disable this function.
Wireless Setup • Choose  Enabled to set up the  Region, SSID , SSID Broadcast , Channel , 
Encryption , and Key. Choose  Disable to disable the wireless set up. 
						

							94Using Your Projector
SSID: Up to maximum length of 32 characters.
Encryption : You can Disable WPA key or select one of 64-bit or 128-bit in 
ASCII or HEX string.
Key : If Encryption is enabled, you have to set key value according to the 
Encryption mode you selected.
RADIUS Server Setup • Set up the IP address, Port, and Key information.
GateKeeper • There are three options:  All Pass : Allow users to access the office network via the wireless projector.
All Block : Block users from accessing the office network via the wireless 
projector.
Internet Only : Block users from the office network but still reserve Internet 
connection capability.
Set Security For SNMP • Setup Write Community information.
Click the  Apply button to save and apply changes.  The projector must be restarted 
for the changes to take effect. 
						

							Using Your Projector95
Projection Setup
Projection Setup
• Resolution : Allows you to select the resolution. Options are: XGA 
(1024 x 768) and WXGA (1280 x 800).
• Login Code : Select how you want the login code to be generated by the 
projector. There are three options: 
• Disable : Login code will not be required when logging in to the system.
• Random : Default is  Random. Login code will be randomly generated.
• Use the following code : Enter a 4-digit code. This code will be used to 
log in to the system.
Projector Setup
•Set up the Model Name , Projector Name , Location , and Contact  
information (up to 21 characters for each field).
Click the  Apply button to save and apply changes.  The projector must be restarted 
for the changes to take effect. 
						

							96Using Your Projector
Change Passwords
This page allows you to chan ge the administrator password.
• Enter New Password : Enter the new password.
• Confirm New Password : Enter the password again and click  Apply.
 
NOTE: Contact Dell if you forget your administrator password. 
						

							Using Your Projector97
Reset to Default
Click the Apply button to restore the wireless/network setup to its factory default 
settings. 
						

							98Using Your Projector
Firmware Update
Use the Firmware Update page to update  your projector’s wireless firmware.
 
NOTE: Please disable and enable wireless/ne twork using the OSD to restart 
the network card for the projector  after firmware upgrade is successful.
To start firmware update, follow these steps: 1 Press  Browse  to select the file to update.
2 Click the  Update button to start. Wait while the system updates the 
firmware in your device.
 
CAUTION: Do not interrupt the update process and this may cause the system 
to crash!
3 Click  OK when the update is complete. 
						

							Using Your Projector99
Projector Control Panel
Projector Information
• Projector Status : There are five status: Lamp On, Standby, Power Saving, 
Cooling, and Warming up. Click the  Refresh button to refresh the status 
and control settings.
• Po w e r  S a v i n g : Power Saving can be set to Off, 30, 60, 90, or 120 minutes. For 
more information, see Power Saving on page 68.
• Alert Status : There are three alert states: Lamp warning, Low lamp life, and 
Temperature warning. Your projector mi ght lock up in protection mode if 
any of the alerts are activated. To exit the protection mode, click the  Clear 
button to clear the Alert Status before you power on your projector. 
						

							100Using Your Projector
Image Control
• Projector Mode : Allows you to select the projector mode, depending on how 
the projector is mounted. There are four projection modes: Front 
Projection-Desktop, Front Projection-Wall Mount, Rear Projection-Desktop, 
and Rear Projection-Wall Mount.
• Source Select : The Source Select menu allows  you to select your projectors 
input source. You can select VGA-A, VGA-B, S-Video, Composite Video, 
HDMI, Wireless Display, USB Display, or USB Viewer.
• Video Mode : Select a mode to optimize the display image based on how the 
projector is being used:
 -  Presentation : Best for presentation slides.
 -  Bright : Maximum brightness and contrast.
 -  Movie : For viewing movies and photos.
 -  sRGB : Provides a more accurate color representation.
 -  Custom : User-preferred settings.
• Blank Screen : You can select On or Off.
• Aspect Ratio : Allows you to select the aspect ratio to adjust how the image 
appears.
• Brightness : Select value to adjust the brightness of the image.
• Contrast : Select value to adjust the display contrast.
Click the  Auto Adjust  button to adjust the settings automatically.
Audio Control
• Audio Input : Select the input source. Options are: Audio-A, Audio-B, 
HDMI, Wireless/LAN, and Microphone.
• Vo l u m e : Select the value (0~20) for audio volume.
• Speaker : Select On  to enable the audio function or select Off  to disable the 
audio function.
Click the  Factory Reset  button to restore the factory default settings.