Dell 2230d User Guide

Replacing the photoconductor kit
The printer notifies you when the photoconductor kit reaches a page maximum. The printer does this by displaying
the “Photoconductor life warning” light sequence or the “Replace photoconductor” light sequence.
Light sequences
Photoconductor life warning
 - Blinking
 - On
Replace photoconductor
 - Blinking
 - Blinking
 - On
When you first receive either light sequence, you should immediately order a new photoconductor kit. While the
printer may continue to function...

To replace the photoconductor kit:
1Open the front door by pressing the button on the left side of the printer and lowering the front door.
2Pull the photoconductor kit and toner cartridge together as a unit out of the printer by pulling on the toner
cartridge handle.
Note: The photoconductor kit and toner cartridge form a unit.
Place the unit on a flat, clean surface.
3Press the button on the base of the photoconductor kit. Pull the toner cartridge up and out using the handle.
4Unpack the new...

5Insert the toner cartridge into the photoconductor kit by aligning the rollers on the toner cartridge with the tracks.
Push the toner cartridge in until it clicks into place.
6Install the unit into the printer by aligning the arrows on the guides of the unit with the arrows in the printer.
Push the unit as far as it will go.
7After you replace the photoconductor kit, reset the photoconductor counter. To reset the counter, see the
instruction sheet that came with the new photoconductor kit....

Moving the printer
Before moving the printer
CAUTION—POTENTIAL INJURY: Follow these guidelines to avoid personal injury or printer damage:
Turn the printer off using the power switch, and then unplug the power cord from the wall outlet.
Disconnect all cords and cables from the printer before moving it.
Lift the printer off of the optional drawer and set it aside instead of trying to lift the drawer and printer at the
same time.
Note: Use the handholds located on both sides of the printer to lift it off...

Setting the printer up in a new location
When the printer is set up, allow clearance around it as shown.
1300 mm (12.0 in.)
2300 mm (12.0 in.)
3200 mm (8.0 in.)
412.7 mm (0.5 in.)
5300 mm (12.0 in.)
Shipping the printer
When shipping the printer, use the original packaging or call the place of purchase for a relocation kit.
Maintaining the printer
95
 

Administrative support
Adjusting Power Saver
Increase or decrease the number of minutes before the printer enters Power Saver mode.
If your printer is connected to a computer by a USB or parallel cable, use the Local Printer Settings Utility for Windows
or Printer Settings for Macintosh.
1Click Setup.
2Ensure that the Power Saver check box is selected.
3Clicking the small arrow buttons, increase or decrease the number of minutes before the printer enters Power
Saver mode. Available settings range from...

Clearing jams
Avoiding jams
The following hints can help you avoid jams:
Use only recommended paper or specialty media. For more information, see “Paper and specialty media guide”
on page 64.
Do not load too much paper. Make sure the stack height does not exceed the indicated maximum height.
Do not load wrinkled, creased, damp, or curled paper.
Flex, fan, and straighten paper before loading it.
Do not use paper that has been cut or trimmed by hand.
Do not mix paper sizes, weights, or types in the same...

Accessing jam areas
Open doors and remove trays to access jam areas. The following illustration shows possible jam areas:
Access pointDescription
1Push button to open the front door. Inside this door is the unit housing the toner cartridge and
photoconductor kit.
2Standard exit bin
3Front door
4Manual feeder door
5Standard 250-sheet tray (Tray 1)
6Optional tray (Tray 2)
7Rear door
Understanding jam lights and access locations
The following table lists the jam lights and messages and provides brief...

Try one of the following:
Remove Tray 1.
Open the front door, and then remove the photoconductor kit and toner cartridge unit.
201.yy Paper jam
 - On
 - On
 - On
Open the front door, and then remove the photoconductor kit and toner cartridge unit.
202.yy Paper jam
 - On
 - On
 - On
Open the front door, and then open the rear door.
231.yy Paper jam
Clearing jams
99
 

 - On
 - Blinking
 - On
Open the front door, and then open the rear door.
233.yy Paper jam
 - On
 - Blinking
 - Blinking
 - On
Try one of the following:
Remove Tray 1.
Open the front door, and then open the rear door.
234.yy Paper jam
 - On
 - Blinking
 - On
Try one of the following:
Open the front door, and then open the rear door.
Remove Tray 1.
Clearing jams
100