DELL 1350cnw User Manual

							Understanding the Printer Menus217
Wireless Status
Purpose:
To display the information on the wireless signal strength. No changes can be 
made on the operator panel to improve the status of the wireless connection.
Va l u e s :
 NOTE: This item is displayed only when the printer is connected with a wireless 
network and 
Wireless LAN is set to Enable.
Wireless Setup
Purpose:
To configure the wireless network interface.
Va l u e s :
Good Indicates good signal strength.
Acceptable Indicates marginal signal strength.
Low Indicates insufficient signal strength.
No Reception Indicates that no signal is received.
 
						

							218Understanding the Printer Menus
Manual Setup Enter (SSID)Specify a name to identify th
e wireless network. Up to 32 
alphanumeric characters can be entered.
Infra
structure Select when you configure the wireless setting through 
the access point such as a wireless router.
No Security
Specify No Security to configure the 
wireless setting without specifying a 
security method from  WEP, WPA-PSK-
TKIP , and  WPA2-PSK-AES.
WEP (64Bit) Specify the WEP Key (64Bit) to use 
through the wireless network. Up to 10 
hexadecimal characters can be entered.
Tr a n s m i t  
KeySpecify the transmit key 
from 
WEP Key 1 , WEP Key 
2 , WEP Key 3 , and WEP Key 
4 .
WEP (128Bit) Specify the WEP Key (128Bit) to use 
through the wireless network. Up to 26 
hexadecimal characters can be entered.
Tr a n s m i t  
KeySpecify the transmit key 
from 
WEP Key 1 , WEP Key 
2 , WEP Key 3 , and WEP Key 
4 .
 
						

							Understanding the Printer Menus219
WPA-PSK-
TKIPSelect to configure the wireless setting 
with the security method of WPA-PSK-
TKIP.
Pass 
Phrase 
EntrySpecify the pass phrase of 
alphanumeric characters 
from 8 to 63 only when 
WPA-PSK-TKIP
 is selected 
for  Encryption .
WPA2-PSK-
AES Select to configure the wireless setting 
with the security method of WPA2-PSK-
AES.
Pass 
Phrase 
EntrySpecify the pass phrase of 
alphanumeric characters 
from 8 to 63 only when 
WPA2-PSK-AES
 is selected 
for  Encryption .
Ad-hoc Select to configure the wireless setting without the access 
point such as a wireless router.
No Security Specify No Security  to configure the 
wireless setting without specifying the 
security method from WEP.
WEP (64Bit) Specify the WEP Key (64Bit) to use 
through the wireless network. Up to 10 
hexadecimal characters can be entered.
Tr a n s m i t  
KeySpecify the transmit key 
from 
WEP Key 1 , WEP Key 
2 , WEP Key 3 , and WEP Key 
4 .
WEP (128Bit) Specify the WEP Key (128bit) to use 
through the wireless network. Up to 26 
hexadecimal characters can be entered.
Tr a n s m i t  
KeySpecify the transmit key 
from 
WEP Key 1 , WEP Key 
2 , WEP Key 3 , and WEP Key 
4 .
 
						

							220Understanding the Printer Menus
 NOTE: This item is displayed only when the printer is connected with a wireless 
network.
Reset Wireless
Purpose:
To initialize wireless network settings . After executing this function and 
rebooting the printer, all wireless networ k settings are reset to their default 
values.
 NOTE: This item is displayed only when t he printer is connected with a wireless 
network.
TCP/IP
Purpose:
To configure TCP/IP settings. 
The change becomes effective after the printer is 
turned off and then on.
Va l u e s :
WPS Push 
Btn. CtrlConfigures the wireless setting with the security method 
of WPS-PBC.
PIN 
Code Start Config.
Configures the wireless setting using the 
PIN code assigned automatically by the 
printer.
Print PIN 
Code Prints the PIN code. Confirm it when you 
enter the PIN code to your computer. 
IP 
Mode Dual Stack*
Uses both IPv4 and IPv6 to set the IP address.
IPv4 Mode Uses IPv4 to set the IP address.
IPv6 Mode Uses IPv6 to set the IP address.
 
						

							Understanding the Printer Menus221
Protocol
Purpose:
To enable or disable each protocol. 
The change becomes effective after the 
printer is turned off and then on.
Va l u e s :
IPv4 Get IP 
AddressPa n e l
Enables the IP address entered on the operator 
panel.
AutoIP* Automatically sets the IP address.
BOOTP Uses BOOTP to set the IP address.
RARP Uses RARP to set the IP address.
DHCP Uses DHCP to set the IP address.
IP Address Manually sets the IP address allocated to the printer.
Subnet Mask Manually sets the subnet mask.
Gateway Address Manually sets the gateway address.
LPD Enable* Enables the LPD port.
Disable Disables the LPD port.
Port9100 Enable* Enables the Port9100 port.
Disable Disables the Port9100 port.
WSD Enable* Enables the WSD port.
Disable Disables the WSD port.
SNMP UDP Enable* Enables the UDP port.
Disable Disables the UDP port.
E-Mail Alert Enable* Enables the E-mail Alert feature.
Disable Disables the E-mail Alert feature.
EWS Enable* Enables an access to Dell Printer Configuration 
Web Tool  embedded in the printer.
Disable Disables an access to  Dell Printer Configuration 
Web Tool  embedded in the printer.
Bonjour (mDNS) Enable* Enables the Bonjour (mDNS).
Disable Disables the Bonjour (mDNS).
 
						

							222Understanding the Printer Menus
Purpose:
To block data received from certain IP addresses through the wired or wireless 
network. You can set up to five IP a ddresses. The change becomes effective 
after the printer is tu rned off and then on.
Va l u e s :
 NOTE: This item is on ly available for LPD or Port9100.
Reset LAN
Purpose:
To initialize wired network data stored  in NVM (non-volatile memory). After 
executing this function and rebooting th e printer, all wired network settings 
are reset to their default values.
Wireless LAN
Purpose:
To enable the wireless connection.
LLTD Disable*Disables the LLTD.
Enable Enables the LLTD.
No. n/
Address (n 
is 1-5.) Sets the IP address for Filter
 n.
No. n/Mask 
(n is 1-5.) Sets the address mask for Filter 
n.
No. n/
Mode (n is 
1-5.) Off*
Disables the  feature for Filter 
n.
Accept Accepts an access from the specified IP address.
Reject Rejects an access from the specified IP address.
Enable* Enables the wireless connection.
Disable Disables the wireless connection.
 
						

							Understanding the Printer Menus223
 NOTE: When you use the USB connection and do not use the wireless connection, 
you need to disable the wireless LAN.
USB Settings
Use the  USB Settings  menu to change printer settings affecting a USB 
port.
 NOTE: Values marked by an asterisk (*) ar e the factory default menu settings.
USB Port
Purpose:
To change the USB settings on your printer. The change becomes effective 
after the printer is turned off and then on.
Va l u e s :
System Settings
Use the System Settings  menu to configure the power saving mode, 
time-out time, job log auto print, mm/inch setting, default pa per size setting, 
and low toner alert setting.
 NOTE: Values marked by an asterisk (*) ar e the factory default menu settings.
PowerSaver Time
Purpose:
To specify the time for transition to power saver mode.
Options:
Enable* Enables the USB interface.
Disable Disables the USB interface.
Sleep 5min.* Specifies the time taken by the printer before it 
enters Sleep mode after it finishes a job.
5–30min.
Deep Sleep 6min.* Specifies the time taken by the printer before it 
enters Deep Sleep mode after it goes into Sleep 
mode.
1–6min.
 
						

							224Understanding the Printer Menus
Enter 5 in Sleep to put the printer in the Sleep mode five minutes after it 
finishes a job. This uses less energy,  but requires more warm-up time for the 
printer. Enter 5 if your printer shares  an electrical circuit with room lighting 
and you notice lights flickering.
Select a high value if your  printer is in constant use. In most circumstances, 
this keeps the printer ready to operat e with minimum warm-up time. Select a 
value between 5 and 30 minutes for th e Sleep mode if you want a balance 
between energy consumption and a shorter warm-up period.
The printer automatically returns to the standby mode from the Sleep mode 
when it receives data from the computer. You can also return the printer to 
the standby mode by pressing any button on the operator panel.
Fault Time-Out
Purpose:
To specify the time taken by the printer before it cancels jobs that stop 
abnormally. The print job is cancelled if it times out.
Options:
Job Time-Out
Purpose:
To specify the amount of time that the  printer waits for data to arrive from 
the computer. The print job is cancelled if it times out. 
Options:
On* 60 sec.* Specifies the time taken by the printer before it 
cancels jobs that stop abnormally.
3–300 sec.
Off Disables the fault time-out.
On* 30 sec.* Specifies the amount of time that the printer 
waits for data to arrive from the computer.
5–300 sec.
Off Disables the job time-out.
 
						

							Understanding the Printer Menus225
mm/inch
Purpose:
To specify the measurement unit displayed after the numeric value on the 
operator panel.
Va l u e s :
 NOTE: The default for mm/inch varies depending on co untry-specific factory 
default.
Def. Paper Size
Purpose:
To specify the default paper size.
Va l u e s :
 NOTE: The default for Def. Paper Size varies depending on country-
specific factory default.
Auto Log Print
Purpose:
To automatically print a job hist ory report after every 10 jobs.
Va l u e s :
 NOTE: The job history report can also be printed using the Report/List 
menu.
millimeter (mm)
Specifies the default measurement unit.
inch ()
A4
Letter
Off* Does not automatically print a job history report.
On Automatically prints a job history report.
 
						

							226Understanding the Printer Menus
Low Toner Msg
Purpose:
To specify whether to show the alert message when toner is low.
Va l u e s :
Maintenance
Use the  Maintenance  menu to initialize the NV (non-volatile) memory, 
configure the plain paper quality adju stment settings, and configure the 
security settings.
 NOTE: Values marked by an asterisk (*) ar e the factory default menu settings.
F/W Version
Purpose:
To display the version of the controller.
Service Tag
Purpose:
To display the service tag of the printer.
Express Code
Purpose:
To display the express service code of the printer.
Paper Density
Purpose:
To specify the paper density.
Va l u e s :
On*Shows the alert message when the toner is low.
Off Does not show the alert message when the toner is low.