DELL 1350cnw User Manual

							Dell Printer Configuration Web Tool127
Printer Settings
The Printer Settings  tab contains the  System Settings, USB Settings, and 
Secure Settings  pages.
System Settings
Purpose:
To configure the basic printer settings.
Va l u e s :
Printer Settings Click the Start button to print the printer settings page.
Device Settings Click the Start button to print the device settings page.
Job History Click the Start button to print the Job History report.
Error History Click the Start button to print the Error History report.
Color Test Page Click the Start button to print the Color Test Page.
Power Saver 
Time - Sleep
*1Specifies the time taken by the printer before it enters Sleep mode 
after it finishes a job.
Power Saver 
Time - Deep 
Sleep Specifies the time taken by the printer before it enters Deep Sleep 
mode after it goes into Sleep mode.
Fault Time-Out Specifies the time taken by the printer before it cancels jobs that 
stop abnormally. The print job  is cancelled if it times out.
Job Time-Out Specifies the amount of time that the printer waits for data to arrive 
from the computer. The print job is cancelled if it times out.
mm / inch
*2Specifies the measurement unit displayed after the numeric value 
on the operator panel.
Default Paper 
Size Specifies the default paper size.
Auto Log Print Specifies if a job history needs to be printed after every 10 jobs.
Low Toner 
Alert Msg Alerts you if the toner is low.
Panel Language Used to set the language on the operator panel.
 
						

							128Dell Printer Configuration Web Tool
USB Settings
Purpose:
To change the USB settings on your printer.
Va l u e s :
Secure Settings
Pa n e l  L o c k
Purpose:
To restrict access to Admin Menu and Report/List  with a password, and 
to set or change the password.
Va l u e s :
*1 Enter 5 in  Sleep to put the printer in the Sleep mode five minutes after it finishes a 
job. This uses less energy, but requires more  warm-up time for the printer. Enter 5 if 
your printer shares an electrical circuit with room lighting and you notice lights 
flickering.
Select a high value if your printer is in  constant use. In most circumstances, this 
keeps the printer ready to operate with minimum warm-up time. Select a value 
between 5 and 30 minutes for the Sleep mode if you want a balance between energy 
consumption and a shorter warm-up period.
The printer automatically returns to the standby mode from the Sleep mode when it 
receives data from the computer. You can also return the printer to the standby mode 
by pressing any button on the operator panel.
*
2 The default for  mm/inch and Default Paper Size  vary depending on country-specific 
factory default.
USB Port To enable the USB interface on your printer.
Pa n e l  L o c k  S e t Restricts access to 
Admin Menu and Report/List with a 
password.
New Password Sets a password required to access 
Admin Menu and Report/
List
.
Re-enter 
Password Enter the new password again to confirm.
 
						

							Dell Printer Configuration Web Tool129
 NOTE: This menu sets a password to lock the operator panel. When you change 
the password for the  Dell Printer Configuration Web Tool, click Set Password  on the 
left frame and set the password.
Login Error
Purpose:
To set the maximum number of failed lo gin attempts before an administrator 
is denied access to  Admin Menu and Report/List .
 NOTE: This item is available only when  Panel Lock Set is set to Enable.
Printer Maintenance
The Printer Maintenance  tab contains the Pa p e r  D e n s i t y, Adjust BTR , 
Adjust Fuser , Auto Registration Adjustment , Color Registration 
Adjustments , Clean Developer , BTR Refresh, Maintenance Chart, Reset 
Defaults , Non-Dell Toner , Adjust Altitude, and Web Link Customization  
pages.
Paper Density
Purpose:
To specify the paper density.
Va l u e s :
Adjust BTR
Purpose:
To specify the optimum voltage settings  for printing for the transfer roller 
(BTR). To lower the voltage, set negati ve values. To increase, set positive 
values.
The default settings may not give the be st output on all paper types. If you 
see mottles on the print output, try to  increase the voltage. If you see white 
spots on the print output, try to decrease the voltage.
 NOTE: The print quality changes depending on the va lues you select for this item.
Plain
Sets the paper density of plain paper.
Label Sets the paper density of labels.
 
						

							130Dell Printer Configuration Web Tool
Va l u e s :
Adjust Fuser
Purpose:
To specify the optimum temperature settings for printing for the fuser. To 
lower the temperature, set negative values. To increase, set positive values.
The default settings may not give the be st output on all paper types. When 
the printed paper has curled, try to lo wer the temperature. When the toner 
does not fuse on the paper properly , try to increase the temperature.
 NOTE: The print quality changes depending on the values you select for this item.
Va l u e s :
PlainSets the reference voltage setting for the transfer roller for plain 
paper within the range of -3 to 3.
Plain Thick Sets the reference voltage setting  for the transfer roller for thick 
plain paper within the range of -3 to 3.
Covers Sets the reference voltage setting for the transfer roller for cover 
paper within the range of -3 to 3.
Label Sets the reference voltage setting for the transfer roller for labels 
within the range of -3 to 3.
Coated Sets the reference voltage setting for the transfer roller for coated 
paper within the range of -3 to 3.
Envelope Sets the reference voltage setting for the transfer roller for 
envelopes within the range of -3 to 3.
Recycled Sets the reference voltage setting for the transfer roller for recycled 
paper within the range of -3 to 3.
Plain Sets the temperature settings for the fuser for plain paper within 
the range of -3 to 3.
Plain Thick Sets the temperature settings for the fuser for thick plain paper 
within the range of -3 to 3.
Covers Sets the temperature settings for  the fuser for cover paper within 
the range of -3 to 3.
 
						

							Dell Printer Configuration Web Tool131
Auto Registration Adjustment
Purpose:
To specify whether to automatically adjust color registration.
Color Registration Adjustments
Purpose:
To specify whether to manually adjust color registration.
Color registration adjustments need to be  made during the initial setup of the 
printer or when the printer is  moved to a different location.
 NOTE: The Color Registration Adjustments  feature can be configured when  Auto 
Registration Adjustment  is set to Off.
Va l u e s :
Label Sets the temperature settings for the fuser for labels within the 
range of -3 to 3.
Coated Sets the temperature settings for the fuser for coated paper within 
the range of -3 to 3.
Envelope Sets the temperature settings for the fuser for envelopes within the 
range of -3 to 3.
Recycled Sets the temperature settings for the fuser for recycled paper within 
the range of -3 to 3.
Auto Correct Click Start to automatically correct color registration.
Color Regi 
Chart Click 
Start to print a color registration chart. The color registration 
chart prints a lattice pattern of yellow, magenta, and cyan lines. On 
the chart, find the values on the right side that are next to the line 
that is perfectly straight for each of the three colors. If the value for 
this line is 0, color registration is not needed. If the value for this 
line is any value other than 0, specify the adjustment values under 
Color Registration Adjustments .
 
						

							132Dell Printer Configuration Web Tool
Clean Developer
Purpose:
To rotate the developer motor and stir the toner in the toner cartridge, to use 
up a toner cartridge when you need to replace it before the end of its life, or to 
stir the toner in a new toner cartridge.
Va l u e s :
BTR Refresh
Purpose:
To specify whether to automatically execute counter measures for curling/
separating discharge of the paper.
Maintenance Chart
Purpose:
To print various charts that can be  used for diagnosing your printer.
Va l u e s :
Color 
Registration 
Adjustments Enter Number
Specifies lateral (perpendicular to paper feed 
direction) and process (paper feed direction) color 
adjustment values indivi dually for Y (Yellow), M 
(Magenta), C (Cyan), LY (Left Yellow), LM (Left 
Magenta), LC (Left Cyan), RY (Right Yellow), 
RM (Right Magenta), and RC (Right Cyan) 
within the range of -5 to +5.
Clean 
Developer Click 
Start to stir the toner in the toner cartridge.
Yellow Toner 
Refresh Click 
Start to clean the toner in the yellow toner cartridge.
Magenta Toner 
Refresh Click 
Start to clean the toner in the magenta toner cartridge.
Cyan Toner 
Refresh Click 
Start to clean the toner in the cyan toner cartridge.
Black Toner 
Refresh Click 
Start to clean the toner in the black toner cartridge.
 
						

							Dell Printer Configuration Web Tool133
Reset Defaults
Purpose:
To initialize NVM (non-volatile memory) for system parameters. After 
executing this function and rebooting the printer, all the menu parameters, 
except the parameters for the network,  are reset to their default values.
Va l u e s :
Non-Dell Toner
Purpose:
To use toner cartridge of another manufacturer.
 NOTE: Using non-Dell-brand toner cartridges may make some printer features 
unusable, reduce print quality and decrease the reliability of your printer. Dell 
recommends only new Dell-brand toner cartridges for your printer. Dell does not 
provide warranty coverage for problems  caused by using accessories, parts, or 
components not supplied by Dell.
 
NOTE: Before you use toner cartridge of another manufacturer, be sure to restart 
the printer.
Adjust Altitude
Purpose:
To specify the altitude of the locati on where the printer is installed. 
GhostClick Start to print a chart to check for ghost printing.
4Colors Click Start to print bands of yellow, ma genta, cyan, and black with 
varying density.
Alignment Click Start to print a chart, and then check for proper alignment of 
the print image on the paper.
Drum Refresh Click Start to print a chart to check the light fatigue of the drum 
cartridge.
Reset Defaults 
and restart 
printer. Click 
Start to initialize the system parameters.
 
						

							134Dell Printer Configuration Web Tool
The discharge phenomenon for charging the photo conductor varies with 
barometric pressure. Adjustments are performed by specifying the altitude of 
the location where the printer is being used.
 NOTE: An incorrect altitude adjustment sett ing leads to poor printing quality, 
incorrect indication of remaining toner.
Web Link Customization
Purpose:
To specify a link used for ordering co nsumables, which can be accessed from 
Order Supplies at:  in the left frame.
Va l u e s :
Print Server Settings
Use the  Print Server Settings  menu to set the type  of printer interface and 
necessary conditions for communications.
The following tabbed pages are displa yed in the top of the right frame.
Print Server Reports
The Print Ser ver Reports  tab contains the Print Server Setup Page  and E-
Mail Alert Setup Page .
Print Server Setup Page
Purpose:
To verify the current settings of TCP/IP (Transmission Control Protocol/
Internet Protocol) and printing ports.  On this page, you can only verify the 
settings of items. If you want to change  the settings, go to the pages in the 
Print Server Settings  tab.
Select Reorder 
URLSelect 
Regular  or Premier  web address to be linked to  Order 
Supplies at:
Regular Displays the regular web address (http://accessories.us.dell.com/
sna) that can be linked to  Order Supplies at:
Premier Displays the premier web address ( http://premier.dell.com) that 
can be linked to  Order Supplies at:
 
						

							Dell Printer Configuration Web Tool135
Va l u e s :
Ethernet*1Ethernet 
SettingsDisplays the current settings of Ethernet 
transmission rate and the duplex settings.
Current 
Ethernet 
Settings Displays the current Ethernet settings.
MAC Address Displays the Media Access Control (MAC) 
address of the printer.
Wireless 
Settings
*2Wireless LAN Displays whether to enable wireless connection.
SSID Displays the name that identifies the network.
Network Type Displays the network type from either the Ad-Hoc 
or Infrastructure mode.
MAC Address Displays the MAC address of the wireless printer 
setting.
Link Channel Displays the channel number of the connection.
Link Quality Displays the quality of the connection.
 
						

							136Dell Printer Configuration Web Tool
TCP/IP 
SettingsIP Mode
Displays the IP mode.
Host Name Displays the host name.
IPv4
*3IP Address Mode Displays the IP address mode.
IP Address Displays the IP address.
Subnet Mask Displays the subnet mask.
Gateway Address Displays the gateway address.
IPv6
*4Enable Stateless 
Address Displays whether to enable the 
stateless address.
Use Manual 
Address Displays whether to set the IP 
address manually.
Manual 
Address
*5Displays the IP address.
Stateless Address 
1-3
*6Displays the stateless 
addresses.
Link Local 
Address
*6Displays the link local address.
Manual Gateway 
Address
*5Displays the gateway address.
Auto Configure 
Gateway 
Address
*6
Displays the gateway address.