Land Rover Defender 90 110 Workshop Book 8 Bulletins Rover

TRANSMISSION I37 
7. Check  that a minimum  clearance of 1,Omm 
exists between  the front face of the reverse 
idler gear  and the  rear  face of the reverse  gear 
on  the 
firstkecond synchromesh  sleeve. If the 
clearance 
is insufficient,  adjust the cross-over 
lever  again. 
8. Return  the firstkecond selector  rail back  to 
neutral. 
9. Remove  the  detent  spring retaining  tool and 
spacers 
Gearbox top cover. 
1. Fit  the  top  cover  gasket. 
2. Fit the top cover locating  it over  the...

TRANSMISSION 
Bell housing. 
1. Fit a new bell housing  gasket. 
2. Locate the bell  housing  squarely  on the 
dowels  and secure  to the  gearbox  with the 
six 
bolts  and  spring washers. 
Gearbox  extension  housing. 
1. Remove the gearbox  assembly  from the vice 
and  detach  the stand. 
2. The  special  nut  retaining  the fifth  gear  to the 
layshaft  must be secured  by  carefully  forming 
the  collar 
of the nut  into  the layshaft  slots, as 
illustrated. 
CAUTION: A round nose tool must...

. ..h ... .. : :;; ::::;  j;, c.  . _._,, ... 
TRANSMISSION 137 
Third/fourth selector rail adjustment 7. Unscrew  the stop bolt. 
8. Select fourth gear  and  screw-in the  stop  bolt 
until  contact 
is made  with the third/fourth 1. Slacken  the third/fourth stop screw  in the 
extension  housing.  selector  shaft. 
2. Select third gear. 
3. Tighten the stop  screw untilit makes  contact 
with  the 
third/fourth selector  rail. 
4. Turn back  the stop  screw one turn. 
5. Return  the gear  lever  to...

I I 
Range Land  Rover Rover Workshop Bulletin 
.r- AIJENTION SERVICE  MANAGER . . .: 5. , 
FEBRUARY 1988 
BULLETIN NUMBER SLR621ENWB4 
LAND ROVER 
1988 MODEL IMPROVEMENTS 
Further supplies of this BdIetin can he obtained, free of charge, from: 
Land Rover  Merchandising  Service 
P.O. Box 534, Erdington Birmingham 824 OQS 
SERVICE Land Rover Service  Division  

n 
101 I INTRODUCTION 
INTRODUCTION 
Also included in the 1988 Year  Land  Rover  model 
improvements  are the  following  items which  are 
fully described  to assist  the workshop.  The first 
operation,  whilst not being  part 
of the 
improvement  programme 
is, nevertheless, a 
continuation 
of the  policy  to replace  material 
gaskets,  where practicable,  with liquid  sealants.  The 
opportunity  has, therefore  been taken 
to include,  in 
this  Bulletin,  the latest,  most significant  change...

BODY n 76 
SUN ROOF LAND ROVER 9OandllO. 
To remove 
4. Raise-up the  rear of the  panel  and withdraw  it 
rearwards  from the sun 
roof exterior surround. 
1. Open  the  roof panel  to its  fullest  extent by 
pulling  the latch  handle  down to the  first  open 
position. 
5. Remove  the two  screws  and  withdraw the 
latch  finisher. 
2. Then  move  the green  button  to the  right  and 
push  the panel  up as far  as the  latch 
will allow 
to  the  fully  open  position. 
3. Move  the red  button...

176 I BODY 
7. Remove the fifteen  screws  and withdraw  the 
outer  frame  retainer. 
8. Lift the  sun roof external  frame  from the 
vehicle. 
9. If necessary,  remove the adhesive- backed 
seal, 
from the  inner  edge of the frame,  that 
seals  it 
to the vehicle  roof. 
To refit 
11. If, removed,  fit the  two  centralising  blocks to 
the  outer  frame  and secure  with adhesive. 
10. To release  the latch  from  the glass 
panel,remove the two screws  and  withdraw 
the  latch  and backing...

I: .-...  ,.,.. :.: ., ,_:. ,t:: I . I. ....*. .... I .,. :. 
BODY 76 
ST2 10 1 M v i 
13.  Clean the area of contact  on the  vehicle  roof 
then  Lower  the frame  into position  on the 
roof. 
14. From  inside  the vehicle,  offer-up the  retaining 
frame  and secure  to the  outer  frame with the 
fifteen  screws. 
15. If removed,  fit the  latch to the glass  panel  with 
the  backing  plate and 
two screws,reversing 
instruction 10. 
16. Secure  the interior  finisher to the  retaining 
frame  with...

76 
ST2105M  
BODY 
5. Using  a screwdriver,  carefully lever the trim 
retaining  button from the 
C post.The button 
is held by a fir-tree type  peg. 
ST2 1 07.M 
71 
I 
6 
8. The top edge of the trim is held  to the  inner 
cant  rail by three  spring 
clips.Strike upwards, 
with  the hand, 
as illustrated,  to release  the 
trim. 
STZlO9M 
6. Remove  the trim  lower  three fixings.  The 
forward  fixing 
is a screw, two washers  and a 
nut. 
7. The  rear and centre  fixings are a screw, washer 
and...