Land Rover Defender 90 110 Workshop Book 8 Bulletins Rover

01 
5- 9 INTRODUCTION. ::.. .-, 
This Workshop  Manual covers the Land  Rover  Ninety  and  One Ten range  of vehicles.  It is primarily  designed  to 
assist skilled  technicians 
in the efficient  repair and maintenance of Land Rover  vehicles. 
Using  the  appropriate  service tools and carrying  out the  procedures  as detailed  will enable  the  operations  to be 
completed  within the time  stated in the  ‘Repair  Operation  Times’. 
The  Manual  has  been  produced  in separate  books;  this...

Always have a fire extinguisher  containing FOAM CO1 GAS, or POWDER  close at hand  when  handling or draining 
fuel,  or when dismantling  fuel systems  and in areas 
whcre fuel  containers  are stored. 
Always disconnect  the vehicle  battery BEFORE  carrying out dismantling  or draining  work 
on a fuel system. 
Whenever 
petroVgasoline is  being  handled,  drained or stored, or  when fuel systems  are being  dismantled  all forms of 
ignition  must be extinguished  or removed,  any head-lamps  used...

-3 & ,= ..., . . ... .. ~ ..,_.,, . . .. 
Special Service Tools 
The use of 
approved  special service tools is important. They are  essential if service operations 
are  to be  carried  out efficiently,  and safely.  The amount  of time  which  they save can be 
considerable. 
Every  special  tool is designed  with the close  co
-operation of Land  Rover Ltd.,  and no tool is 
put  into  production  which has  not  been  tested  and approved  by 
us. New tools  are only 
introduced  where  an operation...

L 
01 LOCATION OF VEHICLE IDENTIFICATION  AND UNIT  NUMBERS i 
VEHICLE  IDENTIFICATION  NUMBER (MN) 
The Vehicle  Identification  Number  and  the 
recommended  maximum  vehicle  weights are stamped 
on  a plate  riveted  to  the 
top of the  brake  pedal  box in 
the engine compartment. 
The  number  is also  stamped  on the  right
-hand  side  of 
the  chassis  forward  of the  spring  mounting  turret. 
Always  quote this number  when writing  to Land Rover 
Limited. 
Key  to Vehicle  Identification...

I. 
1 
.. ..... 
ST663M 
.. 
FRONT AXLE 
Stamped on top of the  left-hand  axle tube. 
REAR  AXLE 
Stamped  on rear  of left-hand  axle tube. 
MAIN  GEARBOX  LT77 - 4 CYLINDER  VEHICLES 
Stamped on a pad  on the  right-hand  side of the gearbox 
immediately below  the oil filler  level plug. 
RR 470M 
TRANSFER  GEARBOX LT230R - 4 CYLINDER 
VEHICLES 
Stamped on  the  casing  on the  left-hand  side of the 
gearbox below the mainshaft  rear bearing housing 
adjacent  to the  bottom  cover.  Stamped 
plate....

GENERAL SPECIFICATION DATA 
... GENERAL  SPECIFICATION  DATA ,?F.,. L:,, -,:: .. .... , ,, . ... 
V8 ENGINE 
ENGINE 
Type ................................................................. 
Number of cylinders ............................................. 
Capacity ............................................................ 
Valve  operation.. ................................................. 
Maximum power - B.H.P.. ................................... 
Maximum power- KW...

04 
Piston rings 
Number  of compression 
..................................... 
Number of oil .................................................. 
No. 1 compression  ring ....................................... 
No. 2 compression ring.. ..................................... 
Width of compression  rings ................................. 
Compression  ring gap ........................................ 
Oil ring  type .................................................... 
Oil ring  width...

GENERAL SPECIFICATION DATA 10411 
I, .n .r ,. 2.25 LITRE PETROL ENGINE 1 .. - . . d :

04 
Piston rings 
Compression ................................................... 2 
Gap  in bore 
.................................................. 0,38 - 030 mm (0.015 - 0.020  in) 
Clearance  in groove 
........................................ 0,046 - 0,097 mm (0.0018 - 0.0038 in) 
Oil control 
...................................................... 1 
Gap  in bore .................................................. 0,38 - 030 mm (0.015 - 0.020  in) 
Clearance  in groove...