D-Link Router DIR-825 User Manual

46D-Link DIR-825 User Manual
Section 3 - Configuration
Enter a name for the inbound filter rule.
Select Allow or Deny.
Check to enable rule.
Enter the starting IP address. Enter 0.0.0.0 
if you do not want to specify an IP range.
E n t e r   t h e   e n d i n g   I P   a d d r e s s .   E n t e r 
255.255.255.255  if  you  do  not  want  to 
specify and IP range.
Click the Add button to apply your settings. 
You must click Save Settings at the top to 
save the settings.
This section will list any rules...

47D-Link DIR-825 User Manual
Section 3 - Configuration
SPI  (Stateful  Packet  Inspection,  also  known  as  dynamic  packet 
filtering) helps to prevent cyber attacks by tracking more state per 
session.  It  validates  that  the  traffic  passing  through  the  session 
conforms to the protocol.
Select one of the following for TCP and UDP ports:
Endpoint Independent - Any incoming traffic sent to an open port 
will be forwarded to the application that opened the port. The port 
will close if idle for 5...

48D-Link DIR-825 User Manual
Section 3 - Configuration
Enter the IP address of packets that will take 
this route.
Enter  the  netmask  of  the  route,  please  note 
that  the  octets  must  match  your  destination 
IP address.
Enter your next hop gateway to be taken if this 
route is used.
The route metric is a value from 1 to 16 that 
indicates the cost of using this route. A value 1 
is the lowest cost and 15 is the highest cost. 
Select  the  interface  that  the  IP  packet  must 
use to transit...

49D-Link DIR-825 User Manual
Section 3 - Configuration
Set the transmit power of the antennas.
Beacons are packets sent by an Access Point to 
synchronize a wireless network. Specify a value. 
100 is the default setting and is recommended. 
This value should remain at its default setting of 
2432. If inconsistent data flow is a problem, only 
a minor modification should be made.
The fragmentation threshold, which is specified 
in  bytes,  determines  whether  packets  will  be 
fragmented.  Packets...

50D-Link DIR-825 User Manual
Section 3 - Configuration
Advanced Wireless Settings
802.11n/a (5GHz)
Set the transmit power of the antennas.
Beacons are packets sent by an Access Point to 
synchronize a wireless network. Specify a value. 
100 is the default setting and is recommended. 
This value should remain at its default setting of 
2432. If inconsistent data flow is a problem, only 
a minor modification should be made.
The  fragmentation  threshold,  which  is  specified 
in  bytes,  determines...

51D-Link DIR-825 User Manual
Section 3 - Configuration
Wi-Fi Protected Setup (WPS)
Enable the Wi-Fi Protected Setup feature. 
Locking the wireless security settings prevents the 
settings from being changed by the Wi-Fi Protected 
Setup  feature  of  the  router.  Devices  can  still  be 
added to the network using Wi-Fi Protected Setup. 
However, the settings of the network will not change 
once this option is checked.
A PIN is a unique number that can be used to add 
the router to an existing network...

52D-Link DIR-825 User Manual
Section 3 - Configuration
This Wizard helps you add wireless devices to the wireless network.
The wizard will either display the wireless network settings to guide you through manual configuration, prompt you to enter the 
PIN for the device, or ask you to press the configuration button on the device. If the device supports Wi-Fi Protected Setup 
and has a configuration button, you can add it to the network by pressing the configuration button on the device and then 
the on...

53D-Link DIR-825 User Manual
Section 3 - ConfigurationUPnP
Internet Ping Block
Internet Port Speed
Multicast Streams
To use the Universal Plug and Play (UPnP™) feature 
click on Enabled. UPNP provides compatibility with 
networking equipment, software and peripherals.
Unchecking the box will not allow the DIR-825 to 
respond to pings. Blocking the Ping may provide 
some extra security from hackers. Check the box 
to allow the Internet port to be “pinged”.
Select  from  the  drop-down  menu  if  you...

54D-Link DIR-825 User Manual
Section 3 - Configuration
Guest Zone
Check to enable the Guest Zone feature. 
The  schedule  of  time  when  the  Guest  Zone  will 
be  active.  The  schedule  may  be  set  to  Always, 
which  will  allow  the  particular  service  to  always 
be enabled. You can create your own times in the 
Tools > Schedules section.
Enter  a  wireless  network  name  (SSID)  that  is 
different from your main wireless network.
Check  to  allow  network  connectivity  between  the...

55D-Link DIR-825 User Manual
Section 3 - Configuration
IPV6
Select Link-Local Only from the drop-down 
menu.
Displays the IPv6 address of the router.
My IPv6 Connection:
LAN IPv6 Address 
Settings:
Link-Local Connectivity