D-Link Router DIR-825 User Manual

16D-Link DIR-825 User Manual
Section 3 - Configuration
If you selected PPPoE, enter your PPPoE username and password. Click 
Next to continue.
Select Static  if  your  ISP  assigned  you  the  IP  address,  subnet  mask, 
gateway, and DNS server addresses.
Note: Make sure to remove your PPPoE software from your computer. The software 
is no longer needed and will not work through a router.
If  you  selected PPTP,  enter  your  PPTP  username  and  password.  Click 
Next to continue.
If you selected L2TP,...

17D-Link DIR-825 User Manual
Section 3 - Configuration
If you selected Static, enter your network settings supplied by your Internet 
provider. Click Next to continue.
Click Connect to save your settings. 
 
Click Reboot Now to reboot the router so the new settings can take effect. 
Once  the  router  is  finished  rebooting,  click Continue.  Please  allow  1-2 
minutes to connect. 
Close your browser window and reopen it to test your Internet connection. 
It may take a few tries to initially connect to...

18D-Link DIR-825 User Manual
Section 3 - Configuration
Manual Internet Connection Setup
Click Manual Internet Connection Setup to begin.
If  you  want  to  configure  your  router  to  connect  to  the 
Internet  using  the  wizard,  click Internet  Connection 
Setup Wizard and refer to page 14. 

19D-Link DIR-825 User Manual
Section 3 - Configuration
Select Dynamic IP (DHCP) to obtain IP Address 
information automatically from your ISP. Select 
this option if your ISP does not give you any IP 
numbers to use. This option is commonly used 
for  cable  modem  services  such  as  Comcast 
and Cox.
The Host Name is optional but may be required 
by some ISPs. Leave blank if you are not sure.
Check  the  box  if  you  are  having  problems 
obtaining an IP address from your ISP.
Enter  the  Primary...

20D-Link DIR-825 User Manual
Section 3 - Configuration
Select PPPoE (Username/Password) from the drop-down menu.
Select Static IP if your ISP assigned you the IP address, subnet mask, 
gateway, and DNS server addresses. In most cases, select Dynamic.
Enter the IP address (Static PPPoE only).
Enter your PPPoE user name.
Enter your PPPoE password and then retype the password in the next 
box.
Enter the ISP Service Name (optional).
Select either Always-on, On-Demand, or Manual.
Enter  a  maximum  idle  time...

21D-Link DIR-825 User Manual
Section 3 - Configuration
Select Static  if  your  ISP  assigned  you  the  IP 
address, subnet mask, gateway, and DNS server 
addresses. In most cases, select Dynamic.
Enter the IP address (Static PPTP only).
Enter  the  Primary  and  Secondary  DNS  Server 
Addresses (Static PPTP only).
Enter the Gateway IP Address provided by your 
ISP.
E n t e r   t h e   S e r v e r   I P   p r o v i d e d   b y   y o u r   I S P 
(optional).
Enter your PPTP username.
Enter your PPTP...

22D-Link DIR-825 User Manual
Section 3 - Configuration
The DNS server information will be supplied by your ISP (Internet Servi\
ce Provider.)
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1400 is 
the default MTU.
The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not 
recommended that you change the default MAC address unless required by your ISP.  You can use the Clone Your PC’s...

23D-Link DIR-825 User Manual
Section 3 - Configuration
Select Static  if  your  ISP  assigned  you  the  IP  address, 
subnet mask, gateway, and DNS server addresses. In most 
cases, select Dynamic.
Enter  the  L2TP  IP  address  supplied  by  your  ISP  (Static 
only).
Enter the Subnet Mask supplied by your ISP (Static only).
Enter the Gateway IP Address provided by your ISP.
Enter the Server IP provided by your ISP (optional).
Enter your L2TP username.
Enter your L2TP password and then retype the...

24D-Link DIR-825 User Manual
Section 3 - Configuration
MTU:
Clone MAC 
Address:
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1400 is 
the default MTU.
The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not 
recommended that you change the default MAC address unless required by your ISP.  You can use the Clone Your PC’s 
MAC Address button to replace the Internet port’s MAC...

25D-Link DIR-825 User Manual
Section 3 - Configuration
Enter the IP address assigned by your ISP.
Enter the Subnet Mask assigned by your ISP.
Enter the Gateway assigned by your ISP.
The DNS server information will be supplied by your 
ISP (Internet Service Provider.)
Maximum  Transmission  Unit  -  you  may  need  to 
change the MTU for optimal performance with your 
specific ISP. 1500 is the default MTU.
The default MAC Address is set to the Internet port’s 
physical interface MAC address on the...