Comdial Scout II Users Guide

Scout II User Guide
Jun ‘02 Comdial 21
2.  INSTALLING SCOUT II
The digital wireless telephone is a proprietary multiline telephone 
that connects directly to a digital station port. 
Use the information in this chapter to learn how to install the digital 
wireless telephone and its accessories.
Section 2.1, Selecting the Installation Location
Section 2.2, Connecting to the Station Jack
Section 2.3, Applying Power to the Base Unit and Charging 
Station
Section 2.4, Wall Mounting the Base and Charger...

Installing Scout II
22 Comdial Jun ‘02
2.1  Selecting the Installation Location 
Select a location for the digital wireless telephone to avoid excessive 
heat or humidity.  Place the base unit of your digital wireless tele
-
phone on a desk or tabletop near a standard 120V AC outlet and 
within reach of the station jack.  Keep the base unit and handset away 
from sources of electrical noise (for example, motors, fluorescent 
lighting, and similar devices).  You may find that you can extend the 
digital...

Scout II User Guide
Jun ‘02 Comdial 23
2.2  Connecting to the Station Jack 
Connect one end of the supplied four-conductor line cord to the  
phone jack on the digital wireless telephone base unit.  Connect the 
other end of this line cord to a digital station port jack.
CAUTION
•  Never install telephone wiring during a 
lightning storm.
•  Never touch uninsulated telephone wires or terminals 
unless you have disconnected the telephone line at 
the network interface.
•  Use caution when installing or...

Installing Scout II
24 Comdial Jun ‘02
2.3  Applying Power to the Base Unit 
and Charging Station
1.  Using only the base unit AC adapter supplied with the Scout II, 
plug the AC adapter cord into the AC adapter input jack on the 
base unit.  Route the cord through the strain relief channel.  
Note:  Use only the supplied base unit AC adapter:  EXP9704.
2.  Plug the EXP9704 AC adapter into a standard 120VAC wall 
outlet.  
3.  IMPORTANT!  Place the power cord so that it does not create a 
trip hazard, or...

Scout II User Guide
Jun ‘02 Comdial 25
Charging Unit
The unique design of your Scout II allows you to place the handset in 
the charging unit with or without the belt clip attached.  
Note:  Use only the supplied charging unit AC adapter:  AD-970
The charging unit also has the ability to charge a second battery with 
or without the handset being charged.  The battery packs can automat
-
ically be recharged either in or out of the handset.  For details on 
charging a second battery, see 
Section 2.7,...

Installing Scout II
26 Comdial Jun ‘02
2.4  Wall Mounting the Base and 
Charger Units
2.4.1  MOUNTING  BASE UNIT USING STANDARD 
WALL PLATE 
The Scout II is designed to be mounted on a standard AT&T or GTE 
wall plate.  To attach the wall mount stand to the base unit, perform 
the following steps.
1.  Slide the wall mount stand into the notches at the top of the 
base unit, push the wall mount stand down and snap it into 
place.
2.  Using only the base unit AC adapter supplied with the Scout II, 
plug...

Scout II User Guide
Jun ‘02 Comdial 27
5.  Plug the other end of the short telephone cord into the modular 
wall jack.  
6.  Place the base unit on the posts of the wall plate and push down 
until it is firmly seated.
7.  Plug the AC Adapter into a standard 120V AC wall outlet.
Note: Do not use an outlet controlled by a wall switch.
2.4.2  MOUNTING BASE UNIT DIRECTLY ON WALL
If you do not have a standard wall plate, you can mount your base unit 
directly on a wall.  Before mounting your phone, consider...

Installing Scout II
28 Comdial Jun ‘02
To mount your Scout II base unit directly to a wall, perform the fol-
lowing steps.
1.  Insert two mounting screws into the wall 3-15/16 inches apart. 
Allow about 3/16 of an inch between the wall and screw heads 
for mounting the phone.
2.  Using only the base unit AC adapter supplied with the Scout II, 
plug the AC adapter cord into the AC adapter input jack on the 
base unit.  Note:  Use only the supplied base unit AC adapter:  
AD970.
3.  Place the AC Adapter...

Scout II User Guide
Jun ‘02 Comdial 29
4.  Plug one end of the telephone line cord into the line jack on the 
base unit.  Then place the telephone cord inside the molded 
channel on the bottom of the wall mount stand.
5.  Place the base unit on the posts of the wall screws and push 
down until it is firmly seated. 

Installing Scout II
30 Comdial Jun ‘02
6.  Plug the other end of the short telephone cord into a telephone 
wall jack.
7.  Plug the AC Adapter into a standard 120V AC wall outlet.
2.4.3  MOUNTING CHARGING UNIT ON WALL
The charging unit is also designed to be wall mounted.  Before 
mounting your charging unit, consider the following:
•  Select a location away from electrical cables, pipes, or other 
items behind the mounting location that could cause a hazard 
when inserting screws into the wall.
•   Make...