Comdial Scout 900MXS Cordless Telephone User Guide

To use Tracker to transfer a call to a park orbit for retrieval and
transmit the call’s park orbit code and caller ID information (if
available),
answer call and pressT/C,
dial extension number,
if the called station does not answer or is busy, dial#01,
pressTALKto end.
NOTE: Tracker parked calls will recall to your station after a
pre-programmed time-out. You can either replace the call into
another Tracker page orbit or retrieve the call for servicing.
If you receive a parked call message on your...

7.16 Using Your Digital Wireless Telephone
With A DSS/BLF Console
Your installer can assign a DSS/BLF console as a companion to
your digital wireless telephone. This companion console ex
-
tends the function button capability of your telephone with ad
-
ditional buttons and status lights. You can program the console
buttons for speed dialing and direct station selection (DSS)
with busy lamp field (BLF) status indication.
When the installer assigns a companion console for your use,
the system...

Sending And Receiving
Non-Verbal Messages
8.1 Using Chapter Eight
This chapter details the several different methods that you can
employ to send and receive messages with your digital wireless
telephone without using verbal communications.
8.2 Lighting The Message Waiting Light
8.3 Sending LCD Messages
8.4 Sending Response Messages
8.5 Using The Assist Button Programming
8.6 Using The Station-to-Station Messaging
Sending And Receiving Non-Verbal Messages
57
8 

8.2 Lighting The Message-Waiting Light
If the system installer designates your station as a central mes
-
sage deskor programs it to have message-wait originate ability,
you can turn on the message-waiting light of any other tele
-
phone. This light lets that telephone user know that you have a
message for him or her.
To turn on the message-waiting light at an idle telephone,
lift handset and pressTALK(if necessary),
press intercom button (if necessary),
dial
3,
dial extension number of station to be...

8.3 Sending LCD Messages
You can set system-supplied messages to be received or dis
-
played by a calling LCD speakerphone. These messages give
information on your telephone status. Get a list of the available
messages from the attendant and write them on the blank list
-
ing chart on the next page.
To turn message on,
lift handset and pressTALK(if necessary),
press intercom button (if necessary),
dial
02,
dial the desired code number from your message list. The
default messages ofBack AtandCallmay...

8.4 Sending Response Messages
By programming one or moreRESPONSE MESSAGEbut
-
tons at unused function buttons F1–F3 on your digital wireless
telephone, you can respond with a variety of messages to many
calling situations. For example, if you call another station and
receive a busy signal or no answer, you can send one of 10 sys
-
tem-supplied messages, or you can send the same message ev
-
ery time the situation arises. Further, you may receive SOHVA
calls and you can respond to them with a non-verbal...

8.5 Using Assist Button Messaging
If you have preprogrammed anASSISTbutton on your tele
-
phone, you can use it to send a message to your supervisor,
asking for assistance while you are on a call. Your message
shows in the supervisor’s telephone display.
To send a message for assistance,
press preprogrammedASSISTbutton,
press preprogrammed DSS button for the telephone user
you need help from. (This is not necessary if you stored
the desired extension number when you do theASSIST
button programming.)
If...

8.6 Using Station-To-Station Messaging
When you call another telephone and no one answers, you may
leave a reminder that you called. Do this by turning on the BLF
light at the called telephone. To allow this to take place, some
-
one must have previously stored as a DSS/BLF button at the
called telephone. If your extension number is not stored as a
DSS at the called telephone, your messaging call goes to the
central message desk, if one is programmed. The central mes
-
sage desk (usually the system...

Programming Your Telephone
9.1 Using Chapter Nine
Use this chapter’s information to understand the various pro
-
gramming steps that you can take with your LCD
speakerphone.
9.2 Programming For Speed Dialing
9.3 Storing Speed Dial Numbers
9.4 Storing DSS Numbers
9.5 Storing the Memory Location Speed Dial Numbers
9.6 Storing The Feature Codes
9.7 Storing The Special Purpose
Feature Buttons
Programming Your Telephone
63
9 

9.2 Programming For Speed Dialing
Speed dialing is a feature that lets you:
dial lengthy numbers using one or two buttons,
store intercom numbers of frequently called telephones.
store frequently used feature codes,
You can store numbers for speed dialing at the following loca
-
tions:
at any function button that isnot now assigned as a line
button or other featureby the system administrator or in
-
staller,
at the keypad numbers 0–9,
at memory number locations within in the handset,
at any...