Comdial Impact Dsu Instructions Manual

3.17.6 SRA Wait Time
Description:Once a caller begins to dial digits, he or she has a certain period of time in which to dial
each new digit. After the caller has stopped dialing digits and the end of the time-out
period has occurred, the system analyzes the dialed digits and routes the call by following
the table-driven routing scheme. Use this procedure to select the SRA wait time.
To Program:1. TypeIS746Sand pressRETURN.
2. From the main menu, type1and pressRETURNfor system COS menu.
3. From the...

3.17.7 Feature Inhibit Programming
Description:You can disable certain features system-wide to provide a basic telephone system for use
in installations where unauthorized users have access to the stations and may tamper with
them.
You can re-enable disabled features by dialing34while you have the feature inhibit
programming feature active or by performing the system default procedure.
To Program:1. Dial29.“FEATURE INHIBIT”
2. Select feature:
—Dial01to disable Line Group 1.
—Dial02to disable Line Group...

3.18 Station Message Detail
Accounting/Reporting (SMDA/SMDR)
The system produces five different call cost reports for printing:
1. Detailed report of all stations.
2. Detailed report of all accounts.
3. Trunk summary report.
4. Department summary report.
5. All records.
The system generates reports automatically for printing whenever it detects that its records storage area is
95 percent full. You can use class of service programming to choose the reports that you want the system
to generate. It...

3.18.1 SMDA Department Numbers
Description:Use this programming feature to define different SMDA department numbers
To Program:1. Dial75.“SMDA PROGRAMMING”
2. Dial04to define department numbers.“SMDA DEPARTMENTS”
3. Dial1–8for department 1–8.“DEPT X”
4. Dial0000–9999for department number.“DEPT X YYYY”
5. DialSfor next department, and repeat steps 3–7 until all departments are numbered.
6. DialSSfor next SMDA feature.
7. DialSSSfor configuration mode.
To change setting, repeat procedure and make different...

3.18.3 SMDA Printout
Automatic SMDA Reports
Description:Call cost reports, produced by the system for printing, are generated automatically
whenever the system detects that the records storage area is ninety-five percent full.
Program the system to automatically generate these reports for printing at a certain time
each day if desired.
To Program:1. Dial75.“SMDA PROGRAMMING”
2. Dial13for auto report time“AUTO TIME XXXX”
—Dial new time in hours and minutes (HH MM in 24 hour time) or dialSto accept
current...

SMDA Report Printout
Description:You can command the system to print several different types of SMDA reports and to
delete all stored SMDA records.
NOTE: The departmental call distribution report reflects statistics based on current
departmental station assignments. Before you use the previous programming
feature to reassign stations to different departments, it is a good practice to:
(1) print the departmental call report and any other desired SMDA reports,
(2) make any desired reassignments, (3) delete...

3.18.4 SMDR Printout
SMDR Printout As System Collected
Description:With this programming step, SMDR provides continuous printout of system-wide station
call activity as it is collected by the system.
To Program:1. Dial77.
2. Dial2.“SMDR PRINT XXX”
3. PressA1to toggle between enable and disable (A1 LED On = Enabled)
—OR—
dial1to enable printing“SMDR PRINT ON”
dial2to disable printing.“SMDR PRINT OFF”
4. DialSfor configuration mode.
To change setting, repeat procedure and make opposite selection.
SMDR Cost...

3.18.5 SMDA Records Deleted By The Attendant
Description:This programming step gives the attendant station the ability to delete SMDA records
when commanded to do so by its user. During day-to-day system operation, when
SMDA records exceed storage capacity, the attendant can delete current records to make
room for additional ones if you perform this programming step.  Typically the attendant
would do this after he or she has requested the system to print an SMDA report. If you
have set the system to...

3.19 Toll Restriction Tables
The toll restriction feature uses entries that you make in 16 different tables to prohibit some or all stations
from calling a wide range of number combinations. In order for toll restriction to take effect, you must
complete the following three-fold process:
·you must program entries in one or more toll tables,
·you must assign toll tables to all appropriate lines,
·you must assign toll tables to all appropriate stations,
·After you program the toll tables and assign them to...

3.19.1 Assign Entries To Toll Restriction Tables
Description:Plan and execute system toll restriction in the sequence detailed in the following steps.
1. Determine the types of dialing restrictions that you wish imposed on the system.
Typically, this includes access codes which result in toll charges, and certain local
numbers as desired.
2. If you wish the restricted dialing codes to be imposed consistently on most or all
stations in the system, list them on one or two tables. If you must allow for a...