Comdial Impact Dsu Instructions Manual

3.19.2 Programming Toll Restriction Table Entries
To Program:1. Dial71.“TOLL TABLE”
2. Dial01–16
—OR—
pressA1–A14,B1,B2for toll table1–16.“XXXXX TABLE Y”
3. Establish an allow or a deny table (A1 LED on = allow, A2 LED On = deny)
—Dial5or pressA1for allow“ALLOW TABLE Y”
—Dial6or pressA2for deny.“DENY TABLE Y”
4. Dial1–4or pressA8–A11for entry number 1–4.“XXXXXX”
5.
Dial
#to clear current entry.
6.
Dial keypad digits (0–9,
#) to enter numbers.“XXXXXX ...”
7. DialSfor next entry and repeat steps 4–6 until...

3.19.3 Assign Toll Restriction Tables To Lines
Description:Once you have created the toll restriction tables, assign them to lines.
To Program:1. Dial72.“ASSIGN TOLL-LINE”
2. Dial01–16or pressA1–A14,B1,B2for toll table 1–16.
3. Dial#to finish entry and display lines.
4. Select line ports (LED On = Lines selected to receive tables)
—Line port 1–16 = Dial01–14or PressA1–A14
—Line port 15, 16 = Dial15,16or PressB1, B2
—Line port 17–24 = Dial17–24or pressHOLDthen dialA1–A8.
5. DialSand repeat steps 2–4 for...

3.19.5 Assign Toll Restriction Tables To Stations
For Night Transfer (of ringing)
Description:Toll tables assigned with this feature have an effect only when the attendant places the
telephone system in the night transfer (of ringing) mode of operation.
To Program:1. Dial74.“ASSIGN TOLL-NITE”
2. Dial01–16or pressA1–A14, B1, B2for toll tables 1–16 (LED On = Selected table).
3. Dial#to finish entry.
4. Select station ports (LED On = station ports to receive tables)
—Station 10–57 = Dial10– 57or...

3.19.7 Assign Toll Restriction Override (TRO) Code
Description:The TRO feature allows users to override the toll restriction that they encounter at other
stations with their own station’s toll restriction assignments. In programming for this
feature, create a four-digit TRO code that users can dial to override the toll restrictions of
any station that they happen to be using and replace it with a toll restriction that matches
their home station.
NOTE:The system marks outgoing line calls that users make...

3.19.8 Positive Disconnect Supervision
Description:When a station is on line with an outside caller and the caller hangs up, the CO may send
a positive disconnect signal to the DSU. You can enable the positive disconnect
supervision feature on a per-line basis. If you enable positive disconnect supervision,
when the system receives the CO’s positive disconnect signal it tells the voice mail
equipment to hang up.
To Program:1. Dial 48.“DIS. SUPERVISION”
2. Select line ports for disconnect supervision (LED...

3.20 The Tracker Paging System
The optional Tracker Paging System allows users to send alpha/numeric or numeric-only messages to
Tracker pagers assigned to station extension numbers. The type of message that the system delivers
depends upon the model Tracker Pager being used.
You should make a record of all programming decisions that you make—it will help you keep track of
what you have done and will help you troubleshoot any problem that might arise later.
NOTE: A lighted LED next to the programming...

3.20.1 Preparing The System
Description:After you install the Tracker base station, you must either master clear the system or
default the system data before you take any further programming action to enable the
feature.
If the Tracker Paging System is part of an initial system installation, you must master
clear the system. If you are upgrading from pre-15A software, you need only to default
the system data.
New Installations
To Program:1. For new installations, master clear the system.
2....

3.20.3 Enabling Tracker Pagers For Stations
Description:After you have enabled the Tracker Paging System as a system-wide feature, enable the
Tracker pagers at individual stations. Station users can disable a Tracker Pager by
pressingINTERCOM #06or enable a Pager by pressingINTERCOMS06.
To Program:1. Dial53.“STATION FEATURES”
2. Dial37.“DISPLAY PAGER”
3. Enable Tracker pager operation
—Dial10–57or pressC10–C57(LED On = Enabled).
4. PressSSfor configuration mode.
To clear current setting, repeat...

3.21 Digital Voice Announcing (DVA)
Digital voice announcing uses a hardware peripheral device (product code DVA01) connected to a digital
station port to play pre-recorded announcements and messages during an in-progress call. The DVA
stores the pre-recorded messages in its memory for recall when needed. While the DVA is not automatic,
it enhances the following features by providing automated voice prompts and dialing instructions to
callers; direct department call with department calling distribution...

3.21.1 Programming For DCD Operation
Description:When you plan to enhance DCD operation with the DVA, you must first completely
program the system for DCD operation.
To Program:To enable the system for DCD operation, refer to the instructions in section 3.11,Direct
Department Callingand complete the following steps:
1. Assign direct department dialing access code (often referred to as a department pilot
number).
2. Assign direct department calling line ports.
3. Assign direct department calling station...