Comdial Executech Model 616, 616b ELECTRONIC KEY SYSTEM Instructions Manual

Programming IMI 66-037 
a. 
9. key on the keypad. The dial tone will sound. 
key to exit the programming mode. 
STATION COS 
The Station COS programming sets the following station 
characteristics: 
DSS/BLF port enable Ringing assignments 
PA port enable Access denied 
Prime line selection Call origination denied 
Ringing line preference Automatic privacy release 
status Night ringing assignment 
Station toll restriction All-call and zone paging 
requirements (616R only) configuration (616R only) 
1. 
2....

Programming IMI 66-037 
6. 
Enable the Jik!&i?aia% b&QG sGGG%aG for the station if this 
feature is desired. 
a. QQ md.g~ &J,,@J +ggg&ggge press the 1 key on the keypad. 0 
b. 
L&I $$~ds& &Ll& ,ggs&g~& press memory key 1 (top left key 
in memory key field). 
7a* Q!? JIi!Q&A -&.kus ~~~&~~~ set the &&&G &J.&& ye&&;rig~ by 
performing the steps listed below. 
At this point, there are no 
toll restriction tables assigned to this station. 
a. 
u Press a memory key for each table to be assigned to the...

Programming 
IMI 66-037 
A line may be programmed for direct ringing (step 8) or delayed 
ringing (step 9) but not for both ringing features. If ste 
f 8 is 
g rogrammed after step 9 for some reason, delayed ringing wi 1 be 
isabled. 
8. 
Set the ~~~g,c_t r.ing selection for each line. 
-7-e i%--rwr-~%. 
a. Press the 
El E key. A tone burst will sound. A default 
condition of no ringing enabled will be set on all lines. 
b. 
Press the line select key for each line on which direct 
ringing is desired. A...

Programming IMI 66-037 
a. 
b. 
14. Set 
for 
all 
a. 
Y 
b. 
C. 
a. Press the A tone burst will sound. A default 
condition of no night ringing will be set on all lines. 
Press the line select key for each line on which night 
ringing is desired. A tone burst will sound after each 
selection. 
. 
A tone burst will sound. This action 
clears the station from zones A, B, and C. 
If it is desired to clear the station from all call, 
press the 
0 ITCM key. 
To assign reception by zone: 
1. Press line select...

Programming 
IMI 66-037 
(2) Press the keypad key that represents the line 
to be paired. 
Another tone burst will sound. 
(3) Repeat this sequence for every line select key. 
c. 
Disable the line select key and the indicator light for 
any lines which are unassigned to a particular Station: 
(1) Press the line select key for the unassigned line; 
(2) Press the 
633 f key on the keypad. 
(3) Repeat this action for each unassigned line. 
16. Press the * 
0 ; key to return to the base programming node....

Table 2a. SYSTEM COS PROGRAMMING REFERENCE 
Circle the desired value lo 
(PULSE/TONE DIALING) 
OR 
9. Press 
q (PULSE DIAL TIMES - PPI & BREAK/MAKE) 
10. Press one key 
13. Press one key 
RESTRICTION PROGRAMMING REFERENCE 
H 
3 
H  

Programming 
Table 2b. LINE COS PROGRAMMING REFERENCE IMI 66-037 
PROCEDURE 
NOTE 
Inter the information in the box at right before performing 
,he programming procedures given below. 
1. Base level program entry 
a. Press 1 INTERCOM 1 
b. Press 
q 
c. Press, in sequence, 
d. Press 
q lzlmam 
2. Press 
q (SET ALL LINES PRIVATE) 
3. Press 1 LINE SELECT 1 1-6 (SET NON-PRIVATE LINES) 
4. Press 
5. Press 1 LINE SELECT 1 
6. Press 
q (DISABLED LINE) 
6. 
q (AUXIL LINE) 
6. H (TELCO LINE) 
6. 
q (PBX LINE)...

Programming 
IMI 66-037 
Table 2c. SPATION COS PROGfUUlMING REFERENCE 
(Copy this sheet as required) 
PROGRAMMING RECORD (Shading Denotes System Default Values) 
NOTE 
I 
:ircl@ or enter Ihe record values al right before proceeding 
, with the programming procedure given below. NOTE 
Enter information or circle desired values below before 
performlng the programmlng procedure given on the left. 
station Location:  1. Base level program entry 
a. press [INTERCOM ] 
b. Press 
q c. Press, in sequence. 
d....

 Proqramminq IMI 66-037 
Table 2d. TOLL RESTRICTION PROGRAMMTN(; REFERENCE 
HOW TO FILL OUT THE 
TOLL RESTRICTION TABLES 
1. Determine the types of dialing restrictions which must be 
imposed on the system. Typically, this includes access 
codes which result in toll charges, and certain local 
numbers as desired. 
2. If the restricted dialing codes will be imposed consistently 
on most or all stations in the system, list them on one or two 
entry tables. If a wide variation in the dialing restrictions is...

Programming IMI 66-037 
RESTRICTION TABLE 1 
(PRESS MEMORY KEY) 
CHOOSE EITHER MODE: ALLOW 
DENY (PRESS KEYPAD KEY 2) 
(PRESS KEYPAD KEY 3) 
b4AXIM”Ml 
PRESS MEMORY KEY MANUALLY DIAL RESTRICTED NUMBER (16 I 
TO SELECT 
I 
I I I I I I I 
TABLE ASSIGNMENT LINES - STATIONS 
RESTRICTION TABLE 2 
(PRESS MEMORY KEY) 
-(PRESS KEYPAD KEY 2) 
IPRFSS KFYPAn KFY 31 
11 
3 1 
I I I 
12 4 
TABLE ASSIGNMENT: LINES STATIONS 
MBER (16 MAXIMUM) 1 I I I I I I I I I I- I I I D16 
CHOOSE EITHER MODE: ALLOW (PRESS KEYPAD KEY...