Comdial Executech Model 616, 616b ELECTRONIC KEY SYSTEM Instructions Manual

							Programming IMI 66-037 
a. 
9. key on the keypad. The dial tone will sound. 
key to exit the programming mode. 
STATION COS 
The Station COS programming sets the following station 
characteristics: 
DSS/BLF port enable Ringing assignments 
PA port enable Access denied 
Prime line selection Call origination denied 
Ringing line preference Automatic privacy release 
status Night ringing assignment 
Station toll restriction All-call and zone paging 
requirements (616R only) configuration (616R only) 
1. 
2. 
3. 
4. 
5. 
Line appearance/key assignment 
Enter the base programming 
mode: Press 
The dial tone will sound. 
Press a two-key sequence on the keypad which corresponds to 
the station to he set (i. e.,to choose station 11 press 1 
1 1. A tone burst will sound to confirm a proper selection. 
An improper selection will result in the dial tone 
Sound 
indicating a return to the base level mode. 
NOTE 
Each time the base programming mode is followed by a 
station select number, the following features are set 
to the default values: the IJSS/F3LF port enable, the PA 
port enable, 
the prime line selection, and the ringing 
line preference enable. Plus, the toll restriction 
table assignments are disabled. 
Set the Q,S_S/,.&~. $Q.Q.~.c& e.~.r,k en_ab_l;e_ ( if Such a Port is 
required) by pressing the 
0 
A tone burst RECALL key. 
will sound to confirm the selection. Skip this step if a 
DSS/RLF console is not installed at the station port 
currently being programmed. If this feature is enabled, do 
not proceed beyond this step unless the port is also to be 
programmed as a PA port. 
Set the 2.~ .p.or.t enaJa1.e (only if a PA port is desired) by 
pressing &? Ei?E-kgypad. 
CD A tone burst will sound to 
F 
confirm this selection. Skip this step if a PA port is not 
desired. 
Do not proceed beyond this step if a PA port 
selection is made. 
Set a .p.r 
ime .l.ine for the station being programmed by pressing 
the 1ineselgcFkey for the line desired or by pressing the 
ITCM key to select the intercom line. A tone burst will 
sound to confirm the selection. If more than one line 
selection key is pressed, the last one pressed selects the 
accepted prime line. 
61  
						

							Programming IMI 66-037 
6. 
Enable the Jik!&i?aia% b&QG sGGG%aG for the station if this 
feature is desired. 
a. QQ md.g~ &J,,@J +ggg&ggge press the 1 key on the keypad. 0 
b. 
L&I $$~ds& &Ll& ,ggs&g~& press memory key 1 (top left key 
in memory key field). 
7a* Q!? JIi!Q&A -&.kus ~~~&~~~ set the &&&G &J.&& ye&&;rig~ by 
performing the steps listed below. 
At this point, there are no 
toll restriction tables assigned to this station. 
a. 
u Press a memory key for each table to be assigned to the 
station. Tables 1 through 8 correspond to the memory keys 1 
through 8. A tone burst will sound with each selection. 
b. Proceed with step 8 if other station COS programming must 
be performed. 
If only programming the toll restriction 
requirements of a station, proceed with step 16. 
set the s&&&g A&J ~~&&.J&.. as sound after each selection to confirm 
it. Thg system default disables station toll restriction- 
a. Press 
0 1 to restrict outgoing TELCO calls numbered 
l-xXxX 
and PBX calls numbered x-1-xxxx. 
b. Press 0: 
0 to restrict outgoing TELCO calls numbered 
O-XxXx 
and PBX calls numbered x-O-xxxx. 
C. Press 
a and (O to restrict both tolls. 
During an initial station programming sequence 
erform all of the 
remaining programming steps given herein (8 - 147. It is recommended 
that they be performed in the order that they are presented. 
During 
subsequent reprogramming of a station, any step, controlling a 
feature that does not need to be reprogrammed, can be skipped over. 
It is not necessary to return to the base programming mode to shift 
from one programming 
step to another. A default value is 
automatically programmed for most of the following characteristics 
when the selection key is pressed. 
This default value is overridden 
by subsequent programming action. 
IMPORTANT NOTE 
STEP 15, WHICH SETS THE LINE APPEARANCE 
TO KEY ASSIGNMENT, 
MUST BE PERFORMED LAST. 
THIS IS NECESSSARY BECAUSE THAT 
PROGRAMMING ACTION MUST BE IMMEDIATEL, v FOLLOWED BY A RETURN 
TO THE BASE PROGRAMMING MODE. 
62  
						

							Programming 
IMI 66-037 
A line may be programmed for direct ringing (step 8) or delayed 
ringing (step 9) but not for both ringing features. If ste 
f 8 is 
g rogrammed after step 9 for some reason, delayed ringing wi 1 be 
isabled. 
8. 
Set the ~~~g,c_t r.ing selection for each line. 
-7-e i%--rwr-~%. 
a. Press the 
El E key. A tone burst will sound. A default 
condition of no ringing enabled will be set on all lines. 
b. 
Press the line select key for each line on which direct 
ringing is desired. A tone burst will sound after each 
selection. 
9. Set the dela2Te.d ring s,e.lection for each line. 
- .-..- .-.. ,_ _ _ ,-._ 
-. - - %-4c-bc+i - 
a. Press the 
CD ii 
F key. A tone burst will sound. A default 
condition of no delayed ringing enabled will be set on 
all lines. 
b. 
Press the line select key for each line on which delayed 
ringing is desired. A tone burst will sound after each 
selection. The time of this delay is 15 seconds. 
10. 
Set the access ~.Q.Q..$Q. s,~.$t.~. for each line . 
- .i .-. -. &.&. 
a. Press the 
GD : key. A tone burst will sound. 
A default 
condition of access not denied will he set on all lines. 
b. 
Press the line select key for each line on which access 
is to be denied. A tone burst will sound after each 
selection. 
11. Set the _c.~J.J ,,o,r&i_n_a,t.~~~ denied .s.t.a.tu.s for each line. 
--i-i- ----rir 
a. 
Press theakey. A tone burst will sound. 
A default 
condition of call origination not denied will be set on 
all lines. 
b. 
Press the line select key for each line on which call 
origination is to be denied. A tone burst will sound 
aftereach selection. 
12. 
Set the acc.e.s.s ._t,o g~$~.g~&g Q&Q.~.~ ~@~$.g for each line . 
-‘-fit - w w 
a. Press the 
0 8 key. A tone burst will sound. A default 
condition of no access to automatic 
privacy release will 
be set on all lines. 
b. Press the line select key for each line on which access 
to automatic privacy release is desired. A tone burst 
will sound after each selection. 
63  
						

							Programming IMI 66-037 
a. 
b. 
14. Set 
for 
all 
a. 
Y 
b. 
C. 
a. Press the A tone burst will sound. A default 
condition of no night ringing will be set on all lines. 
Press the line select key for each line on which night 
ringing is desired. A tone burst will sound after each 
selection. 
. 
A tone burst will sound. This action 
clears the station from zones A, B, and C. 
If it is desired to clear the station from all call, 
press the 
0 ITCM key. 
To assign reception by zone: 
1. Press line select key 1 for zone A 
2. Press line select key 2 for zone R 
3. Press line select key 3 for zone C. 
4. Press line select key 4 for all call 
(if it was cleared in step b). 
To enable origination by zone: 
1. Press line select key 5 for zone A 
2. Press line select key 6 for zone B 
3. Press line select key 7 for zone C 
4. 
Press line select key 8 for all call 
(if it was cleared in step b). 
NOTE 
Step 15 must be performed last. See previous important note. 
15. 
Set the line gpg,e.g~.g~,e $9 &TZ ~.&g.pg& only if current settings+s;G not correct. 
When power was initially applied 
to the KSU, the 
system set the line appearance to key 
assignment 
so that line 1 matched select key 1, line 2 
matched select key 2, etc. (squared pairing). If this 
squared pairing is desired, skip step 15a and b. 
a. Press the 
0 R key on the keypad. A tone burst will 
sound. 
There is no default condition set by pressing 
this key. 
h. Assign the pairing. 
Any desired pairing can be set. 
All 
line select keys can be programmed to select the same 
line if such a condition is desired. 
(1) Press a line select key. A tone burst will sound. 
64  
						

							Programming 
IMI 66-037 
(2) Press the keypad key that represents the line 
to be paired. 
Another tone burst will sound. 
(3) Repeat this sequence for every line select key. 
c. 
Disable the line select key and the indicator light for 
any lines which are unassigned to a particular Station: 
(1) Press the line select key for the unassigned line; 
(2) Press the 
633 f key on the keypad. 
(3) Repeat this action for each unassigned line. 
16. Press the * 
0 ; key to return to the base programming node. 
17. Repeat steps 1 through 16 for each station connected to the 
system. 
18. Press the 
65  
						

							Table 2a. SYSTEM COS PROGRAMMING REFERENCE 
Circle the desired value lo 
(PULSE/TONE DIALING) 
OR 
9. Press 
q (PULSE DIAL TIMES - PPI & BREAK/MAKE) 
10. Press one key 
13. Press one key 
RESTRICTION PROGRAMMING REFERENCE 
H 
3 
H  
						

							Programming 
Table 2b. LINE COS PROGRAMMING REFERENCE IMI 66-037 
PROCEDURE 
NOTE 
Inter the information in the box at right before performing 
,he programming procedures given below. 
1. Base level program entry 
a. Press 1 INTERCOM 1 
b. Press 
q 
c. Press, in sequence, 
d. Press 
q lzlmam 
2. Press 
q (SET ALL LINES PRIVATE) 
3. Press 1 LINE SELECT 1 1-6 (SET NON-PRIVATE LINES) 
4. Press 
5. Press 1 LINE SELECT 1 
6. Press 
q (DISABLED LINE) 
6. 
q (AUXIL LINE) 
6. H (TELCO LINE) 
6. 
q (PBX LINE) Select one feature 
Press that key 
7. Select toll restriction tables 
-Press memory keys 
0 1 selects table 1 
0 2 selects table 2 
0 3 selects table 3 
a through a selects tables 4 through 6 
6. Press 
q (PULSE/TONE DIALING) Select one feature 
Press 
q (TONE ONLY DIALING) 
I Pressthatkey 
9. Press 
q (HOLD ABANDON 50ms) Select one feature 
Press 
q (HOLD ABANDON 300ms) 
3 Press that key 
IO. Repeat steps 5 through 9 for each line 
Il. Press 
12. Press 1 MONITON 
NOTE 
If a time out occurs during the programming sequence, 
perform base level entry again and proceed at program step 
2or4. 
RECORD 
(Shading Denotes System Default Values) 
NOTE 
l Check each line number block for the line feature that is set. 
l Write in the calling number and location status. 
FEATURE 
SETTING 
NON-PRIVATE 1 
DlSABLED I I I I I I I 
AUXlL 1 t 
TOLL 3 
I I I I , I 
RESTRICTION 4 1 
TABLES 
51 I I I I 
CALLING NO. 
67  
						

							Programming 
IMI 66-037 
Table 2c. SPATION COS PROGfUUlMING REFERENCE 
(Copy this sheet as required) 
PROGRAMMING RECORD (Shading Denotes System Default Values) 
NOTE 
I 
:ircl@ or enter Ihe record values al right before proceeding 
, with the programming procedure given below. NOTE 
Enter information or circle desired values below before 
performlng the programmlng procedure given on the left. 
station Location:  1. Base level program entry 
a. press [INTERCOM ] 
b. Press 
q c. Press, in sequence. 
d. Press q El EaelEl 
Station Intercom Number:  2. Press two keys for station number (I.@. 
q q 12) 
3. Press (RECALLI (DSSIBLF CONSOLE PORT) DSS/BLF Console Porf IYES] m 
PA Port m m 
Ringing Line Preference [YESl rx?  4. Press 
q (PA PORT) 
5. Press 
q (Model 616 B) (RINGING LINE 
or 
PREFERENCE) 
Press memory key 1 (Model 616) 
6. Press one [LINE SELECT ] 
Press Or- (PRIME LINE) 
7. Select toll reslrlcllon tables (Model 616 B) 
-Press memory keys 
aselects table 1 
~sel@cIs table 2 
~selects table 3 
a through~selects tables 4 Ihrough 6 
Toll Restriction 
q q 6. Select 1-O 1011 restriction (Model 616) 
-Press q , q or both 
9. Press 
q (DIRECT RINGING) 
10. Press all desired (LINE SELECT] (1-6) 
11. Press 
q (DELAYED RING) 
12. Press all desired [LINE SELECT1 (l-6) Ringing’ 
l3ElElaEllIl IgFg 
13. Press 
q (ACCESS DENIED) 
14. Press all desired ILINE SELECTI (1-6) 
15. Press 
q (CALL ORlGlNATfON DENIED) 
16. Press all desired [LINE SELECT] (1-6) 
17. Press 
q (PRIVACY RELEASED) 
16. Press all desired [LINE SELECT] (l-6) 
19. Press 
q (NIGHT ANSWER RINGING) 
20. Press all desired [LINE SELECT] (l-6) Orig. Denied 
ElElml3ElEl lIw!El 
Night Ringing’ 
ElEll3ml3El m 
21a. Press 
q (Clears Zones A. B & C) 
2lb. Press q m (Clears all call. if desired) 
22. PWSS [LINE SELECT] 1-4 (R@c@~v@ zone A. 8. c. RECEIVE ALL CALL 
Zone Number IAl BIG IALL CALL 
Line Select Number 123 4 
ORIGINATE ALL CALL 
Zone Number IAl BIG [ALLCALL 
Line Select Number 567 0  All Call) 
23. Press [LINE SELECT1 5-6 (Originate Zone A. B. C. 
All Calf) 
24. Press [Ii (LINE APPEARANCEiBUTToN ASSIGN.) 
25. Press one /LINE SELECT/ (key 1-6) 
26. Press key for selected llne 
El-El 
27. Repeat steps 25 and 26 for each assigned line 
26. Press [LINE SELECTI 
of unused line 
29. Press 
q lo disable key and light 
30. Repeal steps 26 and 29 for each unused line 
31. Press 
q 
Line Select 
Key 1 23 4 5 6 7 6 SQUARE 
Line Assigned . Keys 1-o 
(II unasslgned- sekots 
so note here) Lines 1-o 
11 1 2 1 3 1 14 1 5 1 6 1 7 1 6 1 Line Select 1 
32. Press 1 MONITOR] 
NOTE 
If a lime out occurs during the programming sequence. 
perform base level entry again and proceed at program step 
2. Re-enter the station number that was active al lime out. 
l Ringing defdfe to aff Hne8 on 
stetlons 10.17 & 24 I 
68  
						

							 Proqramminq IMI 66-037 
Table 2d. TOLL RESTRICTION PROGRAMMTN(; REFERENCE 
HOW TO FILL OUT THE 
TOLL RESTRICTION TABLES 
1. Determine the types of dialing restrictions which must be 
imposed on the system. Typically, this includes access 
codes which result in toll charges, and certain local 
numbers as desired. 
2. If the restricted dialing codes will be imposed consistently 
on most or all stations in the system, list them on one or two 
entry tables. If a wide variation in the dialing restrictions is 
planned, spread the listings out across several tables. 
3. Strategically group the listings on the tables so that a list of 
restrictions can be applied to a particular station or 
stations. 
4. Press a 
q key in place of a particular digit to condense a 
series of restricted codes into one listing. For example, if 
357, 387, and 397 are to be restricted digits, one entry of 
3 # 7 can be listed to cover them all. 
HOW TO PROGRAM THE 
TOLL RESTRICTION REQUIREMENTS 
1. Fill out the following restriction tables per the above 
instructions. 
2. Press I[ q a q q q -sets base level programming mode if not now active. 
3. Select a table: Press memory key. 
- a selects table 1 
- a selects table 2 
- a selects table 3 
- athrough aselects tables 4 through 8 
4: Set the table mode: Press keypad key. 
- 
q for ALLOW table. 
- 
q for DENY table. 
5. Select a table entry: Press memory key. 
- QI selects entry 1 
- @ selects entry 2 
- a selects entry 3 
- @ selects entry 4 
- new entry selection clears current entry. 5. 
6. 
6. 
7. 
8. 
9. 
IO 
11 
12 
Enter # 1 #and # 0 #to restrict all 3-digit access codes with 
a 1 or 0 as a middle digit. 
Designate each table as a DENY table or as an ALLOW 
table. All entries on a DENY table are dialing restricted 
entries. All ALLOW table entries allows certain override 
conditions to prevail. A typical example follows: A DENY 
table may contain entries which restrict: the dialing of 
1 804 while an ALLOW table may contain entries which do 
not restrict the dialing of 1 800. Another typical entry on an 
ALLOW table is a PBX outside line access code. This entry 
will allow a toll restricted station to have access to an 
outside line for an unrestricted use. 
Once these tables are completely filled out, enter this 
restriction planning on tables 2b and 2c so that the line and 
station programming reference records reflect the planned 
toll restrictions for the system. 
Dial the restricted number from the keypad. 
- 
maximum of 16 digits allowed. 
- 
dial 
q for “match anything” digit. 
Select another table entry: repeat step 5. 
-automatic selection of next entry point occurs after 16th 
digit is dialed in preceding entry. 
Make entry for all four table entry points: repeat steps 5 
through 7. 
Select another table: repeat step 3. 
- 
automatic table selection occurs after 16th digit is dialed 
in 4th entry of preceding table. 
Repeat steps 3 through 8 until all desired toll restriction 
tables are created. 
Press 
q 
Press [MONITOR) or proceed to next system COS 
programming step as found on Table 2a. 
SELECTS TABLE 1 SELECTS TABLE 8 
SELECTS TABLE 2 SELECTS ENTRY 1 
SELECTS TABLE 3 SELECTS ENTRY 2 
SELECTS TABLE 4 SELECTS ENTRY 3 
SELECTS TABLE 5 SELECTS ENTRY 4 
SELECTS TABLE 6 
SELECTS TABLE 7 
SETS ALLOW TABLE 
SETS DENY TABLE 
69-70 (a)  
						

							Programming IMI 66-037 
RESTRICTION TABLE 1 
(PRESS MEMORY KEY) 
CHOOSE EITHER MODE: ALLOW 
DENY (PRESS KEYPAD KEY 2) 
(PRESS KEYPAD KEY 3) 
b4AXIM”Ml 
PRESS MEMORY KEY MANUALLY DIAL RESTRICTED NUMBER (16 I 
TO SELECT 
I 
I I I I I I I 
TABLE ASSIGNMENT LINES - STATIONS 
RESTRICTION TABLE 2 
(PRESS MEMORY KEY) 
-(PRESS KEYPAD KEY 2) 
IPRFSS KFYPAn KFY 31 
11 
3 1 
I I I 
12 4 
TABLE ASSIGNMENT: LINES STATIONS 
MBER (16 MAXIMUM) 1 I I I I I I I I I I- I I I D16 
CHOOSE EITHER MODE: ALLOW (PRESS KEYPAD KEY 2) 
DENY (PRESS KEYPAD KEY 3)  RESTRICTION TABLE 3 
(PRESS MEMORY KEY) 
MANUALLY DIAL RESTRICTED NUMBER (16 MAXIMUM) 
RESTRICTION TABLE 4 
(PRESS MEMORY KEY) 
CHOOSE EITHER MODE: ALLOW (PRESS KEYPAD KEY 2) 
DENY (PRESS KEYPAD KEY 3) 
PRESS MEMORY KEY MANUALLY DIAL RESTRICTED NUMBER (16 MAXIMUM) 
TO SELECT 
ENTRY POINT Dl D2 D3 04 D5 D6 D7 DB D9 DlO Dll D12 D13 D14 D15 D16 
BUTTON ENTRY 
a I 1 
10 2 
11 3 
12 4 
TABLE ASSIGNMENT. LINES STATIONS 
69-70 (b)