Comdial Dxp Proprietary Single Line Telephone Station Users Guide

Conferencing
Stations Together
6.1 Conferencing Telephones Together
·To set up a conference call that includes any combination of
outside lines and intercom parties,
1. Make first call.
2. PressTRANSFER/CONFERENCE;callisplacedonhold
automatically.
3. Make next call.
4. PressTRANSFER/CONFERENCEto establish conference.
5. Repeat the last three procedures to add up to two more parties
for a 5-party conference (including yourself); or, if you are
using a DXPPlusor FX Series system, you can add up to four...

This page remains blank intentionally. 

Using The Other
Telephone Features
7.1 Using The Recall/Flash Feature
Your host system provides certain features that you can access from your
telephone. Your system will probably be configured so that pressingTA P
results in a flash signal to allow access, through dialed codes, to these
features.
·If your system has been configured for flash,
1. PressTA Pto generate a timed flash signal while on line.
·If your system has been configured for recall,
1. PressTA Pwhile on line to disconnect you from the...

At times other telephone users may page you with instructions to meet
them on line. This is known as ameet-mepage.Youcangotothenearest
telephone, dial a code, and be in contact with the paging party.
·To reply to ameet-mepage,
1. Lift handset of nearest telephone and listen for intercom dial
tone.
2. Dial78.
3. Meet paging party on line.
7.3 Switching Between Pulse And Tone
·If the local telephone service is pulse (for rotary dialing), you
can convert to tone while dialing as follows:
1. Press#at point...

·To cancel call forwarding,
1. Lift handset and listen for intercom dial tone.
2. Dial#5.
NOTE: For each call you receive during call forward, you will hear a
short tone burst to remind you calls are being forwarded.
7.5 Using The Tracker Paging System
The Tracker Pager System option allows you to send call back and
parked call messages to Tracker pagers assigned to station numbers.
Along with the parked call message, the system parks the call in orbit
for retrieval by the paged party. The type of...

·To track a called party without first calling them,
1. Lift handset and listen for intercom dial tone.
2. DialS8.
3. Dial station number.
4. Hear confirmation beep (Tracker page accepted) or hear busy
tone (Tracker page not accepted).
5. Hang up handset.
·To use Tracker to transfer a call to a park orbit for retrieval
and transmit the call’s park orbit code and caller ID
information (if available),
1. Answer a call.
2. PressTA P.
3. Dial station number of station that is to receive the call.
4. If the...

·If you receive a parked call message on your Tracker pager,
1. Go to any system station.
2. Lift handset and listen for intercom dial tone.
3. Dial the orbit code (#800–#899) displayed on your pager.
4. Retrieve call.
·To enable or disable a Tracker pager at your station,
1. Lift handset and listen for intercom dial tone.
2. Dial #06to disable,
—OR—
dial #07to enable.
3. Hang up handset.
7.6 Setting Your Personal Ringing Tones
·To alter the ring tone of your telephone so you can distinguish
its ringing...

7.8 Using The IMIST Module
AnImpact SCS8201N telephone equipped with the optional IMIST
module can support an IST device (modem, FAX machine,
industry-standard telephone, etc.) in addition to the telephone.
Depending on system programming, the IST device may be used to make
outgoing calls and receive incoming calls.
The functionality of the IMIST module depends on the type of system
you are using.
• On a DXP system, the IMIST module does not have its own
extension number and can not function...

Sending And Receiving
Non-Verbal Messages
8.1 Lighting The Message-Waiting Light
·To turn on the message-waiting light (and a broken dial tone)
at an idle telephone,
1. Lift handset and listen for intercom dial tone.
2. DialS3.
3. Dial extension number of station to be alerted. The
message-waiting light of called station will flash. The
message-waiting light can only be turned off by either the
person sending the message or the person receiving the
message.
·To turn off the message-waiting light at a...

·To retrieve a message,
1. Observe flashing message-waiting light.
2. Lift handset,
on 8101N-** telephones pressHOLD,
on 8201N-** telephones pressMESSAGE.
Connection to station that left message is automatic.
NOTE: The message-waiting light can only be turned off by either the
person sending the message or the person receiving the
message.
8.2 Sending A System-Supplied LCD
Message To A Calling LCD Speakerphone
·To turn LCD messaging on.
1. Lift handset and listen for intercom dial tone.
2. DialS02.
3....