Comdial Dxp Correspondance Instructions Manual

System ProgrammingDXP Correspondence Manual
Line Disconnect Automatic Camp-OnIf a user at a current station selects a line that a previous station has
released from busy but the system has not yet returned to idle, the
system arranges for the current station to camp-on to the line before
the system makes the line idle. After the system makes the line idle, it
immediately connects the camped-on station to the line. With this
feature disabled, a station cannot select a line until after the system has...

DXP Correspondence ManualSystem Programming
Default Relocation ResponseWhen someone relocates a digital telephone from one station port to
another port, the relocated telephone prompts the user to take action to
determine the station parameters. The user can either accept the
parameters from the station’s original port or accept those from the
new port. He or she has 10 seconds to make the choice. If the user
takes no action, the station assumes the parameters determined by this
programming procedure. If...

5.13
Paging 
Zones
I
Zone Programming
(Zone Names, Transmit Stations, Receive Stations)Use this programming procedure to arrange stations to transmit and
receive voice announcements, to and from a particular group of
stations or to all stations in the system. Also use this procedure to
assign names to paging zones when a site requires named zones.
The zone programming menu lists sub-menu options for all of the
following:
- giving the zone a name,
-specifying the extensions that can transmit paging...

DXP Correspondence ManualSys tern Programming
Relays
External Paging Equipment ControlThe relays serve two different purposes: you can use them to control
an external paging amplifier, or you can use them to track the ringing
signal on any or all line ports. If you connect customer-supplied
external paging equipment to the system’s external paging port and
that equipment requires external control, use this programming
procedure to assign a relay to control the paging equipment. Relays
one and two are...

system ProgfanmingDXP Correspondence Manual
514
Change
PasswordYou can use this programming procedure to change the VDT program
entry password for both the installer and the administrator and change
the main programming station entry code for the system manager and
the attendant..
Installer and Administrator PasswordThe default sequence for both the installer and the administrator VDT
password entries is: I 
SC746 %.You can change part or all of either or both of these passwords to a
customized sequence...

DXP Correspondence ManualSys tern Programming
System Manager PasswordThe default system manager station entry code is as follows:
.INTERCOM button, 
+k # 746 SC. You can change the default password
portion of this station entry code (the 6 portion) to a custom value of
up to 15 digits. Thus, a new station entry could be as follows:
INTERCOM button, 
+k #74 nnnnnnnnnnnnnnn %.You can also change the feature code portion of the system manager
station entry (the 
?k#74 sequence). You can change the feature...

System ProgrammingDXP Correspondence Manual5.15
Feature
RenumberingDialing codes for user features are flexible so that you can renumber
them. You may have to renumber a feature if site requirements dictate
that personal or group intercom numbers fall within a certain block or
sequence. Since new number assignments cannot conflict with‘
existing numbers, the system provides a block of unassigned numbers
that you can use for renumber assignment. At default, the system
assigns blocks of numbers in the...

DXP Correspondence ManualSystem Programming
NOTE: The number block of 5024-5999 is unassigned at default.Use it for code renumbering.
piimq.
If a number conflict exists, the system will prompt you to remove theconflict. Before responding to this prompt with a y (yes), be sure that
doing so will not disturb other programmed features that depend upon
the removed extension number. Before entering a new number, make
sure you delete the original conflict.DXP Correspondence Manual 5 
- 37 

System ProgrammingDXP Correspondence Manual5.16
Programming
The TI
Parameters
5.17
Major Alarm
ReportingWhen the system is using the Tl option, you can program status and
alarm alerting parameters. Also, you can program the DXP loss
insertion that affects audio levels in the individual 
Tl channels. The
specific programming instructions for the 
Tl parameters are shown in
the following list:
-enable Tl status reporting and major alarm alerting,
- program status log parameters,
- program major alarm...

DXP Correspondence ManualSystem ProgrammingChapter Five
Review
Questions1. What is the first item on the system programming menu and
what is its function?
2.How many master clear modes does the DXP have?
3. Master Clear option two clears all of the serial port settings;
true or false?
4. Using the station class of service defaults menu will
automatically reset 
all of the station classes of service to their
defaulted settings; true or false?
5.How would you clear the speed dial and autodial numbers
from...