Comdial Dsu II Non-LCD Station Users Guide

7.3 Switching Between Pulse and Tone
•To convert to tone while dialing—if the local telephone service is
pulse (rotary),
1. Press#at point in dialing sequence where conversion to tone is
required.
NOTE: Pulse/Tone switching can be programmed into memory keys
by pressing # during number storage.
7.4 Forwarding Calls
•To forward personal calls to another telephone,
1. PressINTERCOMand dialS05,
2. Dial extension number of telephone to which calls are to be
forwarded.
•To cancel personal call forward,
1....

7.5 ActivatingThe CallForward
Outside System (CFOS) Feature
The Call Forward Outside System (CFOS) feature gives DSU II station
users the ability to forward line calls to a remote location outside the
system. CFOS remains in effect in the event of a loss of power or a
system reset.
·To activate the CFOS feature,
1. PressINTERCOMS07.
2. Press the speed dial button programmed with the target number,
—OR—
Press a line button,
—OR—
Dial0for the Prime line or last used line,
—OR—
Dial1–4Line Group number.
3....

7.6 Engaging Automatic Set Relocation
NOTE: If this feature has been enabled by your system programmer,
the message-waiting light will flash for several seconds when
you connect your telephone to another location. This means
that the system is waiting to automatically relocate your
extension number and other programmed features to the new
location.
If you do not want your telephone to have its old programming after
relocation, reject the automatic relocation.
•To accept automatic relocation,
1. Do...

7.7 Understanding The DATA Button Light
The optional Data Interface Unit (DIU) provides connections for your
standard multiline digital telephone and an Industry Standard
Telephone (IST) device. The DIU enables you to switch between your
multiline telephone and an IST device (an industry standard telephone,
FAX machine, modem, cordless telephone, or answering machine).
When you have a DIU (either local or remote) assigned to your
multiline telephone, your telephone will have a preprogrammed DATA
button...

7.8 Using The IMIST Module
Impact SCS8212S-** and 8212N-** speakerphones equipped with the
optional IMIST module can support an IST device (modem, FAX
machine, industry-standard telephone, etc.) in addition to the
speakerphone. Depending on system programming, the IST device may
be used to make outgoing calls and receive incoming calls.
The functionality of the IMIST module is similar to the optional Data
Interface Unit (see Section 7.7).
Functioning only on a DSU II system, the IMIST module does not...

7.9 Background Music
If supplied by your main system, music can be set to play through your
telephone speaker.
•To turn music ON,
1. PressINTERCOMS1(speaker light will turn on).
2. Adjust loudness of music with speaker volume control.
•To turn music OFF,
1. PressINTERCOM # 1(speaker light will turn off).
NOTE: Background music automatically turns off during calls and
returns after a call is completed.
7.10 Using The Dynamic Line Button Feature
Certain idle buttons on your telephone (these are usually the...

Sending And Receiving
Non-Verbal Messages
8.1 Lighting The Message Light
If the system installer designates your speakerphone as a central message
desk or programs it to have message-wait originate ability, you can turn
on the message-waiting light of any other telephone. This light lets that
telephone user know that you have a message for him or her.
The message-waiting light is located in different places on the various
model telephones. On the 8124S and 8112S telephones, the message
waiting light is...

•To receive a message at an alerted station,
1. Observe flashing HOLD or MESSAGE light.
2. PressINTERCOM,thenHOLD;orMESSAGE(connection to
station that left message is automatic).
•To turn on the message waiting light at another station,
1. PressINTERCOMS3,orMESSAGE.
2. Dial extension number of station to be alerted (the message
waiting light of called station will flash).
•To turn off the message waiting light at another station,
1. PressINTERCOM # 3,orMESSAGE.
2. Dial extension number of station that...

8.2 Sending Messages To LCD Speakerphones
NOTE: You can set system-supplied messages to be displayed by
calling an LCD speakerphone.
•To turn LCD messaging on,
1. PressINTERCOM.
2. DialS02.
3. Choose message code number (0–9).
4. PressSPEAKER.
8.3 Station-To-Station Messaging
•To activate station-to-station messaging (station must have BLF
appearance at called station),
1. Make intercom call and hear ring-back tone.
2. DialS7; your station’s BLF light turns on at called station.
3. Hang up handset.
•To...

This page remains blank intentionally.