Cisco Prime Nerk 43 User Guide

  
27-57
Cisco Prime Network 4.3.2 User Guide
EDCS-1524415
Chapter 27      Managing Mobile Networks
  GPRS/UMTS Networks
You can also view the following configuration details for a HNB GW service:
Iu/Iuh—The user data is transferred from HNB to HNB GW through the Iuh interface. Iuh interface 
is used to carry user traffic and control information whereas the Iu interface is used to transfer CS 
data as well as PS over IP.
Paging—The Paging memory management scheme is used to store and retrieve data from a...

  
27-58
Cisco Prime Network 4.3.2 User Guide
EDCS-1524415
Chapter 27      Managing Mobile Networks
  GPRS/UMTS Networks
Table 27-38 describes the Iu/Iuh configuration details.
Viewing the Paging Configuration for a Home Node B Gateway Service
To view the Paging details for a HNB GW service:
Step 1Right-click the required device in the Vision client and choose Inventory.
Step 2In the Logical Inventory window, choose Logical Inventory>context>Mobile>HNB GW >hnb 
gw service >Paging. The Paging properties...

  
27-59
Cisco Prime Network 4.3.2 User Guide
EDCS-1524415
Chapter 27      Managing Mobile Networks
  GPRS/UMTS Networks
Viewing the Radio PLMN Configuration for a Home Node B Gateway Service
To view the Radio PLMN details for a HNB GW service:
Step 1Right-click the required device in the Vision client and choose Inventory.
Step 2In the Logical Inventory window, choose Logical Inventory>context>Mobile>HNB GW >hnb 
gw service >Radio PLMN. The Paging properties are displayed in the content pane.
Table...

  
27-60
Cisco Prime Network 4.3.2 User Guide
EDCS-1524415
Chapter 27      Managing Mobile Networks
  GPRS/UMTS Networks
Viewing the Security Configuration for a Home Node B Gateway Service
To view the Security details for a HNB GW service:
Step 1Right-click the required device in the Vision client and choose Inventory.
Step 2In the Logical Inventory window, choose Logical Inventory>context>Mobile>HNB GW >hnb 
gw service >Security. The Security properties are displayed in the content pane. Heartbeat...

  
27-61
Cisco Prime Network 4.3.2 User Guide
EDCS-1524415
Chapter 27      Managing Mobile Networks
  GPRS/UMTS Networks
Table 27-42 describes the Security details.
Viewing the User Equipment Configuration for a Home Node B Gateway Service
To view the User equipment details for a HNB GW service:
Step 1Right-click the required device in the Vision client and choose Inventory.
Step 2In the Logical Inventory window, choose Logical Inventory>context>Mobile>HNB GW >hnb 
gw service >UE. The user equipment...

  
27-62
Cisco Prime Network 4.3.2 User Guide
EDCS-1524415
Chapter 27      Managing Mobile Networks
  GPRS/UMTS Networks
Viewing the Home evolved Node B Gateway Details
The Home evolved Node B (HeNB) provides LTE radio coverage for LTE handsets within a home 
residential coverage area. A HeNBs incorporate the capabilities of a standard eNodeB.
The Home eNodeB Gateway works as a gateway for HeNBs to access the core networks. The HeNB- 
GW concentrates connections from a large amount of HeNBs through an...

  
27-63
Cisco Prime Network 4.3.2 User Guide
EDCS-1524415
Chapter 27      Managing Mobile Networks
  GPRS/UMTS Networks
Step 4Under the selected HeNB GW access service, choose S1 U Relay Configuration. The relay 
configuration details are displayed in the content pane.
NoteThis node is available only if the S1U Relay Status is enabled for an access service.
Table 27-45 describes the S1 U Relay Configuration details. SCTP IP Address The SCTP IP Address allocated by the access service to which the HeNB is...

  
27-64
Cisco Prime Network 4.3.2 User Guide
EDCS-1524415
Chapter 27      Managing Mobile Networks
  GPRS/UMTS Networks
Step 5In the Logical Inventory window, choose Logical Inventory>context>Mobile>HeNB GW. Under 
the HeNB GW node, choose the HeNB GW network service. The network service details, as shown in 
Table 27-46, are displayed in the content pane. Downlink QCI DSCP 
Mapping TableName of the QCI-DSCP mapping table to refer the HENBGW ACCESS 
service towards henb.
Uplink QCI DSCP 
Mapping...

  
27-65
Cisco Prime Network 4.3.2 User Guide
EDCS-1524415
Chapter 27      Managing Mobile Networks
  GPRS/UMTS Networks
Configuring Small Cell Technology
The following commands can be launched from the inventory by right-clicking the appropriate node and 
choosing Commands > Configuration. Your permissions determine whether you can run these 
commands. To find out if a device supports these commands, see the Cisco Prime Network 4.3.2 
Supported Cisco VNEs. 
Cell Configuration 
PLMN ID The Public Land...

  
27-66
Cisco Prime Network 4.3.2 User Guide
EDCS-1524415
Chapter 27      Managing Mobile Networks
  GPRS/UMTS Networks
Command Navigation Input Required and Notes
Create HNB GWRight-click on a context >Commands> 
Configuration > Small CellUse this command to create a 
new HNB Gateway service.
Modify HNB GWcontext>Mobile>HNB 
GW>right-click on a HNB 
service >Commands > Configuration
> Modify HNB GW
context>Mobile>HNB 
GW>right-click on a HNB 
service >Commands > Configuration
> Delete HNB GWUse this...