Cisco 881w Manual
Have a look at the manual Cisco 881w Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 53 Cisco manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
A-3 Cisco Integrated Services Router Hardware Installation Guide Appendix A Technical Specifications Cisco 810 Series Radio Immunity EN301 489-1, EN 301 489-7, and EN301 489-24 Transportation/Storage Conditions Temperature –40 to158 °F (–40 to 70°C) Humidity 5–95% Altitude 4570 m (15,000 ft) AC Power Adapter Power Source 100–240 VAC In-ceiling Plenum No IP41 No Extended Shock-vibe No Maximum Power Consumption 25 W Maximum Output Power Rating 20 W Operating Temperature –13 to 140 °F (–25 to 60 °C) PoE+ Splitter Power Source PoE+ (IEEE802.3at Class 4) In-ceiling Plenum Yes IP41 No Extended Shock-vibe No Maximum Power Consumption 25 W Maximum Output Power Rating 20 W Operating Temperature –13 to 140 °F (–25 to 60 °C) Embedded WiFi Antenna Frequency Range — 2.4–2.5 Ghz 4.9–5.875 Ghz Peak Gain — 4 dBi (2.4 GHz) 6 dBi (5.875 Ghz) Voltage Standing Wave Ratio — 2.5:1 maximum for all bands Nominal Impedance — 50 ohms 1. Routers shipped in People’s Republic of China. Table A-1 Cisco 812 ISR Specifications (continued) DescriptionC812G+7-K9 (3G only)C812G-CIFI+7-E-K9 C812G-CIFI+7-N-K9 C812G-CIFI-V-A-K9 C812G-CIFI-S-A-K9 (3G + WiFi)
A-4 Cisco Integrated Services Router Hardware Installation Guide Appendix A Technical Specifications Cisco 810 Series Mean Time Between Failure Ground Benign Environment Ta b l e A - 2 lists the Mean Time Between Failure (MTBF) values for Cisco 812 ISRs. The MTBF is calculated based on the Ground Benign condition. The values may be adjusted based on the different router usage. Cisco 819 Series This section provides router, port, cabling specifications, and power adapters for the Cisco 812 ISRs and contains the following topics: Router Specifications, page A-4 Mean Time Between Failure Ground Benign Environment, page A-8 Supported Power Adapters, page A-9 WarningUltimate disposal of this product should be handled according to all national laws and regulations. Statement 1040 NoteFor compliance and safety information, see the Regulatory Compliance and Safety Information Roadmap that was shipped with the router and Regulatory Compliance and Safety Information for Cisco 800 Series Routers. Router Specifications Ta b l e A - 1 lists the operational limits of the Cisco 819 ISR. Operating the router outside of the limits specified is not supported. For the complete list of SKUs available for each Cisco 819 ISRs, see the “SKU Information” section on page 1-14. Table A-2 MTBF Values SKUs MTBF (hours) C812G-CIFI-V-A-K9 C812G-CIFI-S-A-K9210,000 C812G-CIFI+7-E-K9 C812G-CIFI+7-N-K9280,000 C812G+7-K9 340,000
A-5 Cisco Integrated Services Router Hardware Installation Guide Appendix A Technical Specifications Cisco 810 Series Table A-3 Cisco 819 ISR Specifications DescriptionHardened Design Specification (Cisco 819HG and Cisco 819HG-4G ISRs)Non-Hardened Design Specifications (Cisco 819G and Cisco 819G-4G ISRs)Hardened Design Specifications (C819HGW and C819HWD ISRs) Physical Characteristics Dimensions (H x W x D) 1.73 x 7.7 x 8.1 in (44 x 196 x 206 mm)1.67 x 7.7 x 7.2 in (42 x 196 x 183 mm)1.73 x 7.7 x 9.0 in (44 x 196 x 229 mm) Weight 3.3 lb (1.5 kg) 2.3 lb (1.0 kg) 3.4 lb (1.54 kg) Maximum Power Consumption11 W 20 W Environmental Operating Ranges Operating Temperature and Altitude–13 to 140°F (–25 to 60°C)32 to 104°F (0 to 40°C)–13 to 140°F (–25 to 60°C) Derate max operating temperature 1.5°C per 1000 feet above 5000 ft 10,000 ft maximum Humidity Maximum 95% non-condensing RHMaximum 85% non-condensing RHMaximum 95% non-condensing RH Environmental Tests Ingress Protection Rating IP 41 per IEC 60529 for Vertical Falling Water, Pollution Degree 3IP 20 per IEC 60529 IP 41 per IEC 60529 for Vertical Falling Water, Pollution Degree 3 Humidity Non-condensing Relative Humidity: 5% to 95% Pollution Pollution 3 for Dust Military Standard MIL-STD-810G Method 514.6: Procedure 1 Category 4, Secured Cargo - Common Carrier MIL-STD-810G Method 514.6: Procedure 1 Category 20, Ground Vehicles MIL-STD-810G Method 516.6. Procedure 1, Functional Shock MIL-STD-810G Method 516.6. Procedure 5, Crash Hazard MIL-STD-810G Method 516.6. Procedure 6, Bench Handling Vibration and Shock (Railway Vehicles)EN61373 Functional Random Vibe - Category 1, Class B EN61373 Simulated Non-op Long-life Vibe - Category 1, Class B EN61373 Non-op Shock, Class B Heavy-Duty Vehicle ApplicationsSAE J1455 Operating Random Vibe, Cab Mounted Truck SAE J1455 Operating Sinusoidal Vibe, Category 3 SAE J1455 Non-operating Sinusoidal Vibe, Category 3 SAE J1455 Handling Drop Test Certifications
A-6 Cisco Integrated Services Router Hardware Installation Guide Appendix A Technical Specifications Cisco 810 Series Standard Safety CertificationsUL 60950-1, 2nd edition; CAN/CSA C22.2 No. 60950-1, 2nd edition, EN 60950-1, 2nd edition; CB to IEC 60950-1, 2nd edition with all group differences and national deviationsUL 60950-1, 2nd edition; CAN/CSA C22.2 No. 60950-1, 2nd edition, EN 60950-1, 2nd edition; CB to IEC 60950-1, 2nd edition with all group differences and national deviations; S/NZS 60950-1, first edition (Australia/New Zealand) EMC Emissions EN55022/CISPR22, CFR 47 Part 15, ICES003, VCCI-V-3, AS/NZS CISPR22, CNS13438, CISPR22, CNS13438, EN300-386, EN61000-3-2, EN61000-3-3, and EN61000-6-1 EMC Immunity EN55024/CISPR24, (EN61000-4-2, EN61000-4-3, EN61000-4-4, EN61000-4-5, EN61000-4-6, EN61000-4-11), and EN300-386 Radio Immunity EN301 489-1, EN 301 489-7, and EN301 489-24 Transportation/Storage Conditions Temperature –40 to158°F (–40 to 70°C) –40 to185°F (–40 to 85°C) Humidity 5–95% Altitude 4570 m (15,000 ft) Router AC Power Adapter1 Input Voltage 85–264 VAC 100–240 VAC nominal Maximum Power Consumption25 W Maximum Output Power Rating20 W (5 VDC, 4 Amps) Router DC Power Adapter Input Voltage 12 VDC nominal PWRx-20W-12VDC (10 VDC to 36 VDC operating range) 24 VDC nominal PWRx-20W-24VDC (18 VDC to 75 VDC operating range) Maximum Power Consumption 25 W Maximum Output Power Rating20 W (5 VDC, 4 Amps) Table A-3 Cisco 819 ISR Specifications (continued) DescriptionHardened Design Specification (Cisco 819HG and Cisco 819HG-4G ISRs)Non-Hardened Design Specifications (Cisco 819G and Cisco 819G-4G ISRs)Hardened Design Specifications (C819HGW and C819HWD ISRs)
A-7 Cisco Integrated Services Router Hardware Installation Guide Appendix A Technical Specifications Cisco 810 Series Altitude Operating: –500 to 10,000 ft, de-rating operating temperature 1°C per 1,000 feet Non-operating: –1,000 to 30,000 ft Cable Length Input cable: 1 m Output cable: 1.3 m Inrush Current 50 A @ 25°C Temperature Operating: –30 to 60°C, still air condition Non-operating: –40 to 85°C Humidity Operating: 10% to 95%, non-condensing Non-operating: 10% to 95%, non-condensing Thermal Shock Operating: –20 to 60°C at 0.5°C per minute Non-operating: –40 to 85°C with change over time between 2 and 3 minutes. Vibration Operating: 0.41 grms from 3 to 500 Hz with spectral break points of 0.0005 g2/Hz at 10 Hz and 200 Hz and 5 dB/octave roll off at each end; 2 hours per axis. Non-Operating: 1.12 grms from 3 to 500 Hz with spectral break points of 0.0065 g2/Hz at 10 Hz and 100 Hz and 5 dB/octave roll off at each end; 30 minutes per axis. Shock Half sine (operating): Duration =
A-8 Cisco Integrated Services Router Hardware Installation Guide Appendix A Technical Specifications Cisco 810 Series Mean Time Between Failure Ground Benign Environment Ta b l e A - 4 lists the Mean Time Between Failure (MTBF) values for Cisco 819 ISRs. The MTBF is calculated based on the Ground Benign condition. The values may be adjusted based on the different router usage. Antenna (Diversity and Antenna 3G-ANTM1919D) Antenna Dimensions 7.63 x 0.94 x 0.63 in (19.38 x 2.39 x 1.60 cm) Frequency Range 806 to 960 MHz and 1710 to 2170 MHz Gain 0 decibels relative to isotropic (dBi) (806 to 960 MHz) and 0 dBi (1710 to 2170 MHz) Maximum Power 25 W Connector TNC male Voltage Standing Wave Ratio < 2.5:1 Nominal Impedance 50 ohms 1. AC Power Adapter is not IP 41 rated. Installation must include protection of the adapter and power plug from water. 2. Contact Martek Power directly for details. Table A-3 Cisco 819 ISR Specifications (continued) DescriptionHardened Design Specification (Cisco 819HG and Cisco 819HG-4G ISRs)Non-Hardened Design Specifications (Cisco 819G and Cisco 819G-4G ISRs)Hardened Design Specifications (C819HGW and C819HWD ISRs) Table A-4 MTBF Values SKUs MTBF (hours) Cisco 819HG and Cisco 819G ISRs C819HG-U-K9 C819G-U-K9380,000 C819HG+7-A-K9 C819HG+7-K9 C819G+7-A-K9 C819G+7-K9420, 000 C819HG-S-K9 C819HG-V-K9 C819HG-B-K9 C819G-S-K9 C819G-V-K9 C819G-B-K9280, 000 Cisco 819HGW, Cisco 819HWD, and Cisco 819H ISRs
A-9 Cisco Integrated Services Router Hardware Installation Guide Appendix A Technical Specifications Cisco 810 Series Supported Power Adapters Ta b l e A - 5 and Ta b l e A - 6 list the supported power adapters for Cisco 819 ISRs. The PWR1 AC and DC adapters uses molex connector while PWR2 uses barrel-type connector.C819HGW-S-A-K9 C819HGW-V-A-K9220,000 C819HGW+7-E-K9 C819HGW+7-N-K9 C819HGW+7-A-A-K9293,000 C819HWD-E-K9 C819HWD-A-K9630,000 C819H-K9 1,000,000 Cisco 819HG-4G and Cisco 819G-4G ISRs C819HG-4G-V-K9 C819G-4G-V-K9214,000 C819HG-4G-A-K9 C819G-4G-A-K9226,000 C819HG-4G-G-K9 C819G-4G-G-K9293,000 Table A-4 MTBF Values (continued) SKUs MTBF (hours) Table A-5 Cisco 819G ISR Power Adapters Power AdapterNominal Input RangeC819G-4G-A-K9 C819G-4G-V-K9 C819G-4G-G-K9 (4G LTE SKUs)C819G+7-K9 C819G-B-K9 C819G-S-K9 C819G-U-K9 C819G-V-K9 (3GSKUs) PWR1-20W-AC 100–240 VAC — Yes PWR2-20W-AC 100–240 VAC Yes — PWR1-20W-12VDC 12 VDC — Yes PWR2-20W-12VDC 12 VDC Yes — PWR1-20W-24VDC 24 VDC — Yes PWR2-20W-24VDC 24 VDC Yes — PWR2-22W-20-60VDC 20-60VDC Yes — Martek MBRH 0500-B/Q21 24 VDC — Yes Martek MBRH 0500-C/Q21 52 VDC — Yes
A-10 Cisco Integrated Services Router Hardware Installation Guide Appendix A Technical Specifications Cisco 810 Series Martek MBRH 0500-D/Q21 72 VDC — Yes Martek MBRH 0500-D/2Q21 24 VDC Yes Yes Martek MBRH 0500-D/2Q21 52 VDC Yes Yes Martek MBRH 0500-D/2Q21 72 VDC Yes Yes Martek MBRH 0500-D/2Q21 110 VDC Yes Yes Martek MBRH 0500-B/Q22 24 VDC Yes — Martek MBRH 0500-C/Q22 52 VDC Yes — Martek MBRH 0500-D/Q22 72 VDC Yes — Martek MBRH 0500-D/2Q22 24 VDC Yes Yes Martek MBRH 0500-D/2Q22 52 VDC Yes Yes Martek MBRH 0500-D/2Q22 72 VDC Yes Yes Martek MBRH 0500-D/2Q22 110 VDC Yes Yes Table A-5 Cisco 819G ISR Power Adapters Power AdapterNominal Input RangeC819G-4G-A-K9 C819G-4G-V-K9 C819G-4G-G-K9 (4G LTE SKUs)C819G+7-K9 C819G-B-K9 C819G-S-K9 C819G-U-K9 C819G-V-K9 (3GSKUs) Table A-6 Cisco 819H ISR Power Adapters Power AdapterNominal Input RangeC819HG-4G-A-K9 C819HG-4G-V-K9 C819HG-4G-G-K9 (4G LTE SKUs)C819HG+7-K9 C819HG-B-K9 C819HG-S-K9 C819HG-U-K9 C819HG-V-K9 (3G SKUs)C819HGW-S-A-K9 C819HGW-V-A-K9 C819HGW+7-E-K9 C819HGW+7-N-K9 C819HGW+7-A-A-K9 (3G + WiFi SKUs)C819HWD-E-K9 C819HWD-A-K9 (WiFi SKUs)C819H-K9 (Serial SKU) PWR1-20W-AC 100–240 VAC — Yes — — — PWR2-20W-AC 100–240 VAC Yes — Yes Yes Yes PWR1-20W-12VDC 12 VDC — Yes — — — PWR2-20W-12VDC 12 VDC Yes — Yes Yes Yes PWR1-20W-24VDC 24 VDC — Yes — — — PWR2-20W-24VDC 24 VDC Yes — Yes Yes Yes Martek MBRH 0500-B/Q2124 VDC — Yes — — — Martek MBRH 0500-C/Q2152 VDC — Yes — — — Martek MBRH 0500-D/Q2172 VDC — Yes — — —
A-11 Cisco Integrated Services Router Hardware Installation Guide Appendix A Technical Specifications Cisco 860, 880, 890 Series Cisco 860, 880, 890 Series This section provides router, port, and cabling specifications for the Cisco 860 series, Cisco 880 series, and Cisco 890 series ISRs. It contains the following topics: Router Specifications, page A-12 Wireless Access Point, page A-22 FE and GE Port Pinouts, page A-23 Console and Auxiliary Port Connector Pinouts, page A-24 FXS and FXO Port Connector Pinouts, page A-24 VDSL2 Port Connector Pinouts, page A-24 ADSL2+ Port Connector Pinouts, page A-25 V.92 Port Connector Pinouts, page A-25 Martek MBRH 0500-D/2Q2124 VDC Yes Yes Yes Yes Yes Martek MBRH 0500-D/2Q2152 VDC Yes Yes Yes Yes Yes Martek MBRH 0500-D/2Q2172 VDC Yes Yes Yes Yes Yes Martek MBRH 0500-D/2Q211 1 0 V D C Ye s Ye s Ye s Ye s Ye s Martek MBRH 0500-B/Q2224 VDC Yes — Yes Yes Yes Martek MBRH 0500-C/Q2252 VDC Yes — Yes Yes Yes Martek MBRH 0500-D/Q2272 VDC Yes — Yes Yes Yes Martek MBRH 0500-D/2Q2224 VDC Yes Yes Yes Yes Yes Martek MBRH 0500-D/2Q2252 VDC Yes Yes Yes Yes Yes Martek MBRH 0500-D/2Q2272 VDC Yes Yes Yes Yes Yes Martek MBRH 0500-D/2Q221 1 0 V D C Ye s Ye s Ye s Ye s Ye s Table A-6 Cisco 819H ISR Power Adapters (continued) Power AdapterNominal Input RangeC819HG-4G-A-K9 C819HG-4G-V-K9 C819HG-4G-G-K9 (4G LTE SKUs)C819HG+7-K9 C819HG-B-K9 C819HG-S-K9 C819HG-U-K9 C819HG-V-K9 (3G SKUs)C819HGW-S-A-K9 C819HGW-V-A-K9 C819HGW+7-E-K9 C819HGW+7-N-K9 C819HGW+7-A-A-K9 (3G + WiFi SKUs)C819HWD-E-K9 C819HWD-A-K9 (WiFi SKUs)C819H-K9 (Serial SKU)
A-12 Cisco Integrated Services Router Hardware Installation Guide Appendix A Technical Specifications Cisco 860, 880, 890 Series G.SHDSL Port Connector Pinouts, page A-25 Data BRI Port Connector Pinouts, page A-26 Voice ISDN BRI Interface Pin Numbers and Functions, page A-27 SFP Port Connector Pinouts, page A-27 Cable Specifications, page A-28 WarningUltimate disposal of this product should be handled according to all national laws and regulations. Statement 1040 NoteFor compliance and safety information, see Regulatory Compliance and Safety Information Roadmap that was shipped with the router and Regulatory Compliance and Safety Information for Cisco 800 Series Routers. NoteThe product has some color variation on the Power Pin. This will not impact product performance or reliability. Router Specifications This sections contains the following: All Models Except Cisco 860VAE Series, page A-12 Cisco 860VAE Series, page A-14 Cisco 860VAE-W-A-K9, Cisco 860VAE-W-E-K9, and Cisco 860VAE-POE-W-A-K9 Series, page A-15 Cisco 870 Series, page A-16 Cisco 880 Series, page A-17 Cisco 880G Series 3G Wireless Integrated Services Router, page A-19 Cisco 880VA Series, page A-19 Cisco 890 Series, page A-21 All Models Except Cisco 860VAE Series Ta b l e A - 7 lists the system specifications for all models except the Cisco 860VAE series routers.